seemed to have been able to fix this problem by correcting a mistake of setting up the /www folder incorrectly as i put the DWC.zip folder inside rather than just transferring the content of the folder into the /www folder.
Best posts made by stevenrsearles
-
RE: WebControl Rel 1.2 problem
-
RE: WebControl Rel 1.2 problem
yeah everything is working very smoothly now but i had put my sd into my computer and did the upload that way and since it had been so long since the last time I updated I had to make the /www folder and dropped the whole dwc folder into it. Over all i really like the duet over listing to the r2d2 chatter of the arduino.
Latest posts made by stevenrsearles
-
RE: WebControl Rel 1.2 problem
yeah everything is working very smoothly now but i had put my sd into my computer and did the upload that way and since it had been so long since the last time I updated I had to make the /www folder and dropped the whole dwc folder into it. Over all i really like the duet over listing to the r2d2 chatter of the arduino.
-
RE: WebControl Rel 1.2 problem
seemed to have been able to fix this problem by correcting a mistake of setting up the /www folder incorrectly as i put the DWC.zip folder inside rather than just transferring the content of the folder into the /www folder.
-
WebControl Rel 1.2 problem
I have recently updated all firmware (iap4e.bin, duetwififirmware.bin, duetwifiserver.bin and duetwebcontrol.zip)from 1.81 to 1.2. Now i can connect through pronterface and can see that the new firmware is uploaded the sd card is mounted but when i try to open the web interface it comes back with Your Duet rejected the HTTP request: page not found.
-
RE: It's out! RepRapFirmware 2.0 and 1.21.1 released
But that’s for the web control which on the list is the last to be upgraded if updating all firmware.
-
RE: It's out! RepRapFirmware 2.0 and 1.21.1 released
So I'm about to try to update firmware from 1.18 to 1.21 which i believe to be the most up to date. As i completely messed up the last update and had to do it the hard way I decided to just ask the questions on how to do it rather than just end up asking how to fix it. I read on wiki that to update all files you have to do them in this order: DuetWiFiFirmware, DuetWiFiServer, DuetWebControl. which makes sense as thats what I botched up before, but reading on it said Sometimes we may do synchronised releases of firmware, where more than one firmware component needs to be updated at the same time to maintain compatibility. So would have to use this option or what would be the best way to make this leap. I'm assuming I don't have to do every upgrade I have missed and can just jump to the 1.21.
-
RE: Can't get connected to the Duet3d board.
ok I think i got it figured out now i just went back in and uncommented out the M552 S1 command and then connected to the duet wifi entered in the defult ip and was prompted to enter in the ssid and password can now connect via my network so just on to looking at how to update the firmware but thanks for your speedy response and putting out such good products. Oh and i was thinking about upgrading my build plate was curious if there was a way to control two heated 200/300 beds to make it 400/300mm on a 3d printer with the option to only run one if the other wasn't being used?
-
RE: Can't get connected to the Duet3d board.
Yes it’s for a WiFi and I’m looking through the files now to find some sort of indication of the firmware it’s running and not really finding anything other than it saying config file for dc42 duet firmware but I believe it’s the 1.19 or 1.18? I haven’t updated it in at least a year if that helps.
-
RE: Can't get connected to the Duet3d board.
I recently changed my router out without thinking of changing the wifi config on my board i got rid of the old router, now trying I'm trying to reconnect to my duet wifi so through the terminal of my mac it fails as well as through pronterface. I went into the config.g file and commented out the M552 S1 command still with now luck of connecting. i was curious if there was just a way to load my new ssid and password onto the sd card using a text editor as i don't currently have any other pc besides my mac i can't do the 3rd option. oh and Im probably out of date as far as firmware updates as well so should i just start downloading the files for that at the same time I'm trying to figure this out or just wait till i can actually get connected.
-
RE: Endstop configuration
LJ12A3-4-Z/BX NPN wired
output to cathode, anode to E0 STP pin
ground to ground
power to vin
think i got a bat43 diode but might have been a 1N4148 cant remember right now what one radio shack had in stock at the time and its heat shrinked at the time -
RE: Endstop configuration
mechanical switch from closest to the switch out
1green
2
3black
4redduet from top to bottom (if wifi is in bottom right hand corner)
1black
2red
3green