Thanks for the helping hands here, really.
After few days of testing i am sure i will go back. The Gcode driven System and the Webinterface are really great.
It prints currently on my tronxy but its simply to loud. I tried an stepper from stepper online on y axis i have arround but its the same.
Damn. i wish i had read further...
This is a dealbreaker for me.
Thanks for the answers.
@dc42 said in Motors much louder than on MKS+TMC2208:
Use S1 to enable interpolation.
Motor idle noise can often be reduced by changing the off-time in the stepper driver configuration. There is a thread about how to do this (search for "motor idle noise"). It's even easier in the new 2.02beta1 firmware, because there is a separate M569 parameter to set the off time.
Forgot to mention, i am allready on latest beta.
@wilriker said in Motors much louder than on MKS+TMC2208:
@stephan said in Motors much louder than on MKS+TMC2208:
As its done my config creation tool its very stock. I tried to set S3 on M350 as it feels that its not using stealthchop? Nothing changed.
Duet Wifi does not support stealthChop but only spreadCycle. I am not sure what will be selected when you use
S3here but I guess it will fall back to spreadCycle.As to reducing stand-still noise as @dc42 mentioned look at [Reducing Stand-Still Noise].(https://duet3d.dozuki.com/Wiki/Reducing_Stand-Still_Noise).
What are the specs of your motors? Especially rated current, resistance and inductance?
Hard to say about the specs. They are stock tronxy and no data available. They are Nema17 40mm long.
nothing googleable.(i know that this do not help)
Duet wifi does not support stealthChop ? Seriously?
regardig to this:
https://duet3d.dozuki.com/Wiki/Gcode#Section_M350_Set_microstepping_mode
There is a switch?
EDIT added board diag:
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.01beta2(RTOS) running on Duet WiFi 1.02 or later
Board ID: removed
Used output buffers: 3 of 20 (7 max)
=== RTOS ===
Static ram: 28484
Dynamic ram: 95996 of which 0 recycled
Exception stack ram used: 324
Never used ram: 6268
Tasks: NETWORK(ready,328) HEAT(blocked,1248) MAIN(running,3592)
Owned mutexes:
=== Platform ===
Last reset 00:01:56 ago, cause: software
Last software reset at 2018-08-13 15:36, reason: User, spinning module GCodes, available RAM 6284 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 50.5, current 50.7, max 51.0
Supply voltage: min 24.1, current 24.2, max 24.4, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max 41/128
Driver 1: standstill, SG min/max 0/185
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-08-13 15:38:45
Slowest loop: 7.42ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 239, MaxWait: 11369ms, Underruns: 0, 0
Scheduled moves: 28, completed moves: 28
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 9.19ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.19
WiFi MAC address 60:01:94:7e:eb:a8
WiFi Vcc 3.10, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 37360
WiFi IP address 192.168.2.120
WiFi signal strength -44dBm, reconnections 0, sleep mode unknown
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
Dear All.
I had a hard time to pay the price for my duet wifi. Until now i only have the board itself.
My printer is a tronxy X3s, which is a CR 10 clone.
Before switching to duet i used MKS 1.4 with TMC2208 drivers. It was not noticeable, even if the drives were moving.( slower than 50mm/s)
Now with duet wifi i have whining noise during idle and a lot louder movement sounds in comparision to MKS + TMC2208.
I have seen many threads pointing to wiring/lower current and such. So the only thing changed here is the duet board as the motors were
quiet before. In result i wont bet on wiring as the documentation is very good for duet. What can i do?
Stepper motors are 1.8° "Chinesian Brand". here is my configuration:
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Aug 13 2018 00:16:32 GMT+0200 (Mitteleuropäische Sommerzeit)
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Network
M550 PRainer ; Set machine name
M552 S1 ; Enable network
M587 S"Funkefiez 2" P"d3rd1gg3"; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes backward - X
M569 P1 S0 ; Drive 1 goes backward - Y
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 S3 ; Configure microstepping with interpolation
M92 X80 Y80 Z400 E95.2 ; Set steps per mm
M566 X15 Y15 Z2 E2 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z300 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z100 E1000 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I40 ; Set motor currents (mA) and motor idle factor in per cent
M84 S0 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z300 S0 ; Set axis maxima
; Endstops
M574 X1 Y1 S0 ; Set active low endstops
; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X35 Y5 Z2 ; Set Z probe trigger value, offset and trigger height
M557 X40:280 Y20:280 S20 ; Define mesh grid
; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic saving after power loss is not enabled
; Custom settings are not configured
As its done my config creation tool its very stock. I tried to set S3 on M350 as it feels that its not using stealthchop? Nothing changed.
Thanks
derdigge
EDIT: added codeblock.