Best posts made by steevebecker

undefined

Hi
the arrival of Duet 3 Mainboard is a great news,
have you already planned a date for its integration in the Config Tool ?
thanks

undefined

Hi Duet Forum.
I have spent 2 days on RRF3 and Duet 3. I was my first hours on it ... It's a pleasure, i like this board. I'm moving from another board + Marlin to this one.
Of course it was not so obvious, but with the Documentations (already great) and the forum postsss, I made good progress.
3 Axis+ Endstops / 2 extruders + Sensors + Fans / BED / Heated Chamber / ... everything works. few things are not working yet, i'll write other posts about them.

I share here my config.g, hopes it could help :

; Configuration file for Duet 3 (firmware version ?.0??)
; executed by the firmware on start-up
; oct 2019 : X/Y/Z E1/E2 BED/CHAMBER OK - BL (not ready) SERVO (not ready)
; DUET 3 6HC + 1 extension board 3HC (address 1.)
;
; General preferences
G90			; send absolute coordinates...
M83			; ...but relative extruder moves
M550 P"QualupQ3"	; set printer name Qualup Q3 http://www.spiderbot.eu/qu3-high-temperature/?lang=en

; Network
M552 P0.0.0.0 S1	; enable network and acquire dynamic address via DHCP
M553 P0.0.0.0		; netmask
M554 P0.0.0.0		; gateway
M586 P0 S1		; enable HTTP
M586 P1 S0		; disable FTP
M586 P2 S0		; disable Telnet

; Drives
;M569 P0 S1		; physical drive 0 goes forwards / driver 0 unable on this board
M569 P1 S1		; X physical drive 1 goes forwards
M569 P2 S1		; Y physical drive 2 goes backwards
M569 P3 S1		; Z0 physical drive 3 goes forwards
M569 P4 S1		; Z1 physical drive 4 goes forwards
M569 P1.0 S1		; E0 physical drive 1.0 on expansion board goes forwards
M569 P1.1 S1		; E1 physical drive 1.1 on expansion board goes forwards

M584 X1 Y2 Z3 E1.0:1.1				; set drive mapping 1 stepper on X, Y and 2 Steppers (Z3 instead of Z3:4 because Moteur Z1 not plug on Driver 4 at this time) on Z and Extruder
M350 X16 Y16 Z16 E16:16 I1			; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E4074.37:4074.37      ; set steps per mm

M566 X900 Y900 Z120 E150:150			; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1200 E1200:1200		; set maximum speeds (mm/min)
M201 X500 Y500 Z100 E250:250			; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1200 E800:800 I30		; set motor currents (mA) and motor idle factor in per cent

M84 S30					; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1			; set axis minima
M208 X300 Y250 Z300 S0			; set axis maxima

; Endstops
M574 X1 S1 P"io6.in"			; X min active high endstop switch / pin io3.in doesnt work use 6 instead
M574 Y1 S1 P"io4.in"			; Y min active high endstop switch
M574 Z1 S1 P"io5.in"			; Z min active high endstop switch

;Servo				;not working for the moment
;M950 S0 C"io7.out"		;not working for the moment
;M280 P0 S1500 I1		;not working for the moment

; Z-Probe					;not working for the moment
;M558 P9 C"zprobe.in" H5 F120 T3000           	; FW v3 BLTouch connected to Z probe IN pin
;M950 S0 C"exp.heater3"                       	; FW v3 create servo/gpio 0 on heater 3 pin on expansion connector
;G31 P500 X10 Y20 Z2.5                        	; set Z probe trigger value, offset and trigger height
;M557 X15:6 Y15:195 S20                      	; define mesh grid

; TEMPERATURE Sensors
M308 S0 P"temp0" Y"thermistor" T100000 B3950			; BED temperature sensor
M308 S1 P"1.temp1" Y"thermistor" T4606017 B5848 C0 R4700 H0 L0	; head 0 temperature sensor on expansion board ==> DYZE 500
M308 S2 P"1.temp2" Y"thermistor" T4606017 B5848 C0 R4700 H0 L0	; head 1 temperature sensor on expansion board ==> DYZE 500
M308 S3 P"temp1" Y"thermistor" T100000 B3950			; Chamber temperature sensor
M308 S4 P"temp2" Y"thermistor" T100000 B3950			; CAMERA IR temperature sensor

; Heaters
M950 H0 C"out0" T0 Q100				; BED heater 3 uses the out0 pin, sensor 0
M950 H1 C"1.out1" T1				; HEAD heater 1 uses the out1 pin on expansion board and sensor 1
;M950 H1 C"1.out1" T1 A584.4 C256.6 D6.4 S0.50	; HEAD heater 1 uses the out1 pin on expansion board and sensor 1 ==> DYZE PID Cartbridge
M950 H2 C"1.out2" T2                            ; HEAD heater 2 uses the out2 pin on expansion board and sensor 2
M950 H3 C"out1" T3                             	; CHAMBER heater 3 uses the out1 pin and sensor 3
M950 H4 C"out2" T4                             	; IR Camera heater 4 uses the out2 pin and sensor 4

; Maximum Temperatures 	Currently (September 2019), RRF3 does not support M143.
;M143 H0 S380 C0	; BED max Temp 300°C
;M143 H1 S500 C0	; Extruder 1 max Temp 500°C
;M143 H2 S500 C0	; Extruder 2 max Temp 500°C
;M143 H3 S380 C0	; Chamber max Temp 300°C

; Minimum Temperatures
;M302 P1 S240 R240	; minimun extruder 1 Temperature 240°C extrusion and retract
;M302 P2 S240 R240	; minimun extruder 2 Temperature 240°C extrusion and retract

; Fans
M950 F0 C"1.out7"      	; Extruder 1 fan 0 !F1 don t work ... ???  on pin out 7 pwm on expansion board 
M950 F2 C"1.out8"      	; Extruder 1 fan 2 on pin out 8 pwm on expansion board
M950 F3 C"out7"      	; Chamber fan 3 on pin out 7 pwm
M950 F4 C"out8"        	; IR Camera fan 4 on pin out 8 pwm

; Tools
M563 P1 D0 H1 F0 S"Extruder 1"	; define tool 1 - F1 don t work... ???
G10 P1 X0 Y0 Z0			; set tool 1 axis offsets
G10 P1 R0 S0			; set initial tool 1 active and standby temperatures to 0C

M563 P2 D1 H2 F2 S"Extruder 2"	; define tool 2
G10 P2 X0 Y0 Z0			; set tool 2 axis offsets
G10 P2 R0 S0			; set initial tool 2 active and standby temperatures to 0C

M563 P3 H3 F3 S"Chamber"	; define tool chamber
G10 P3 R0 S0			; set initial tool 3 active and standby temperatures to 0C

M563 P4 H4 F4 S"Camera IR"      ; define tool IR Camera
G10 P4 R0 S0			; set initial tool 4 active and standby temperatures to 0C

; Custom settings are not defined