Ah thank you David! That resolved it!
Latest posts made by snomon
-
M32 File Not Found
Good Morning Everyone,
I'm having a weird problem for the past week in that I keep getting an error:M32 Fan base(0).gcode
Error: M32: GCode file "Fan base.gcode" not foundI tried putting it in the root directory and in a subdirectory, however I keep getting the same error.
I also tried updating to the latest stable firmware:Firmware Name: RepRapFirmware for Duet WiFi
Firmware Electronics: Duet WiFi 1.0
Firmware Version: 1.20 (2017-12-23)
WiFi Server Version: 1.20b10
Web Interface Version: 1.20Any and all help is greatly appreciated and thank you in advance
-
RE: CONSTANT AJAX disconnect errors
Hi guys, I'm having the same problem..Im trying to tell it to print something but it keeps giving me AJAX errors..ctrl+r a few times, i get in at some point. The print then keeps messing up and having me to reset it, not sure why
2:55:56 AMM122
=== Diagnostics ===
Used output buffers: 3 of 32 (15 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4SD-6J9F6-3S46N-12X7W
Static ram used: 21176
Dynamic ram used: 96104
Recycled dynamic ram: 1504
Stack ram used: 1304 current, 5920 maximum
Never used ram: 6368
Last reset 00:12:18 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 3136 bytes (slot 4)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 9.7ms
MCU temperature: min 51.1, current 53.7, max 55.9
Supply voltage: min 23.4, current 24.1, max 24.6, under voltage events: 0, over voltage events: 0
Driver 0: stalled standstill
Driver 1: stalled standstill
Driver 2: stalled standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 2017-09-21 02:55:52
Slowest main loop (seconds): 0.167053; fastest: 0.000034
=== Move ===
MaxReps: 6, StepErrors: 0, FreeDm: 240, MinFreeDm 234, MaxWait: 10780ms, Underruns: 0, 0
Scheduled moves: 5, completed moves: 5
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19.2
WiFi MAC address 60:01:94:34:40:06
WiFi Vcc 3.14, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 36896
WiFi IP address 192.168.20.81
WiFi signal strength -57dBm
Reconnections 0
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
2:55:49 AMConnection established!
2:55:24 AMDisconnected.
2:55:16 AMConnection established!
2:55:11 AMDisconnected.
2:55:03 AMConnection established!
2:55:01 AMDisconnected.
2:54:53 AMConnection established!
2:54:15 AMDisconnected.
2:52:10 AMConnection established!
2:46:32 AMDisconnected.
2:43:49 AMConnection established!
2:41:46 AMDisconnected.
2:39:46 AMConnection established!
2:38:11 AMDisconnected.
2:33:01 AMConnection established!
2:32:52 AMDisconnected.
2:32:40 AMCalibrated 6 factors using 13 points, deviation before 0.028 after 0.014
2:31:48 AMM32 Enclosure bracket v10(1).gcode
File Enclosure bracket v10(1).gcode selected for printing
2:30:54 AMM0 H1
File Enclosure bracket v10(0).gcode print time was 0h 9m
2:30:07 AMM25
Printing paused
2:25:29 AMConnection established!
2:24:55 AMDisconnected.
2:21:20 AMCalibrated 6 factors using 13 points, deviation before 0.091 after 0.024
2:20:42 AMM32 Enclosure bracket v10(0).gcode
File Enclosure bracket v10(0).gcode selected for printing
2:20:14 AMM0 H1
File Enclosure bracket v10(0).gcode print time was 0h 9m
2:19:53 AMM25
Printing paused
2:11:17 AMCalibrated 6 factors using 13 points, deviation before 0.071 after 0.014
2:10:35 AMM32 Enclosure bracket v10(0).gcode
File Enclosure bracket v10(0).gcode selected for printing
2:10:08 AMM122
=== Diagnostics ===
Used output buffers: 1 of 32 (14 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4SD-6J9F6-3S46N-12X7W
Static ram used: 21176
Dynamic ram used: 96200
Recycled dynamic ram: 1408
Stack ram used: 4048 current, 9104 maximum
Never used ram: 3184
Last reset 00:31:37 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 3136 bytes (slot 4)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 54.7, current 55.3, max 55.6
Supply voltage: min 23.4, current 24.0, max 24.4, under voltage events: 0, over voltage events: 0
Driver 0: standstill
Driver 1: stalled standstill
Driver 2: stalled standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 2017-09-21 02:10:06
Slowest main loop (seconds): 0.176147; fastest: 0.000000
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.245 0.225 0.020 -0.266 -0.374
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is ready with "M122" in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19.2
WiFi MAC address 60:01:94:34:40:06
WiFi Vcc 3.14, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 32424
WiFi IP address 192.168.20.81
WiFi signal strength -57dBm
Reconnections 0
HTTP sessions: 1 of 8
Socket states: 0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
2:10:00 AMM0 H1
File Enclosure bracket v10.gcode print time was 0h 14m -
RE: Duet failed after 4 days of usage, Keeps disconnecting from wifi..
I posted the issue on the ultibot forum and someone stated that upgrading to 1.19.2 fixed this problem. I'll try it later tonight and post my results back here
-
RE: Duet failed after 4 days of usage, Keeps disconnecting from wifi..
Hello David,
On the Ultibot forums they cautioned users not to upgrade the firmware, probably for their own testing purposes..I will try it later today and get back to you on it -
RE: Duet failed after 4 days of usage, Keeps disconnecting from wifi..
Oh I also reset the cache on both my mac and windows to confirm it wasn't that and tried safari/chrome.
-
Duet failed after 4 days of usage, Keeps disconnecting from wifi..
Good Morning Everyone,
I would like to take a moment to thank you for taking the time to look at this thread.
So I finally assembled UltiBots D300VS a couple days ago and every thing seems to be working fine until yesterday when I kept getting kicked out of the web interface due to "AJAX" errors. I ignored it thinking it was the wifi just acting up but this morning I have been trying to connect into the web interface with no avail. Ultibots has not updated their firmware to 1.19 yet so I am stuck on 1.18.1.- I power cycled the D300VS, thinking it may help
- Didn't work so I connected to prointerface to M552 S0 then M552 S1 to restart the server
- After doing this a few times I noticed it was emitting DuetWifi again, so I reconfigured it to my wifi
- Didn't work but I saw a post where someone just configured their wifi signal channel from auto to a single channel, so I tried that (Tried M552 S0 and S1 again )
- Tried updating the router, even though the rest of the devices are good (Tried M552 S0 and S1 again )
- Then I reinstalled the firmware via the SD card option and then SAM-BA
- Then I came across a few threads to update the wifi firmware via M997 S1 (Wifi) and M997 S2 (Webinterface)
Alas I came here to post something as I could not find another post (well I did find another post but David mentioned updating to a beta 1.19).
This is the error message:
M552 S1
SENDING:M552 S1
WiFi server starting up
DuetWiFiServer version 1.03 (ch fork)
Flash size 4194304, free RAM 32840 bytes, WiFi Vcc 3.14V, host name: duetwifi, reset reason: Turned on by main processor
WiFi server connected to access point Fireworks, IP=192.168.20.81, signal strength=-43dBm
DuetWiFiServer version 1.03 (ch fork)
Flash size 4194304, free RAM 32584 bytes, WiFi Vcc 3.14V, host name: duetwifi, reset reason: Exception
WiFi server connected to access point Fireworks, IP=192.168.20.81, signal strength=-45dBmThe "reset reason: Exception" part appears every time I try connecting to it via the ip address (I tried via the host name but that didn't work on my mac or windows)
If anyone wants it this is M122 the diagnostics
M122
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (12 max)
=== Platform ===
Static ram used: 20320
Dynamic ram used: 72784
Recycled dynamic ram: 1104
Stack ram used: 3280 current, 4112 maximum
Never used ram: 32752
Last reset 00:32:57 ago, cause: reset button or watchdog
Last software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Spinning module during software reset: GCodes, available RAM 33080 bytes (slot 4)
Error status: 0
[ERROR] Error status: 0Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 34.7, current 41.2, max 45.6
Supply voltage: min 1.1, current 1.3, max 1.4, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 1.458130; fastest: 0.000000
=== Move ===
MaxReps: 0, StepErrors: 0, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
Probe change coordinates:
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
Code queue is empty.
=== Network ===
WiFiServer is running
SPI underruns 0, overruns 0
=== Webserver ===
HTTP sessions: 0 of 8