Posts made by sniper23

@Phaedrux I'm in Turkey right now.

Hello, everyone. After using BLtouch for years, I think it's time to switch to the less problematic z-probe solution. Effector tilt is a huge problem so I need a solution for eliminating that completely. I'm seeing that Smart Effector Duet claims to eliminate it but I can't buy it as it seems out of stock. But I can buy Precision Piezo but I don't know if it can eliminate effector tilt. I've searched the internet and couldn't find proper info about that as people seem to use XY or Cartesian Printers.

Or I need a solution for BLtouch to eliminate tilt if possible.

I couldn't find proper info about this.

My old 8 GB sd card is dead. As 8 GB cards are no longer sold, I'm seeing the minimum option 32 GB or larger. So, I would like to ask if Duet Wi-fi can use 32 GB or larger SD cards? also in what format? exFAT?

@rjenkinsgb said in Uneven Fixed Delta Printer bed with Bltouch and 3D Touch:

I suggest you take the M500 out your config.g, then re-run the full delta calibration sequence, followed by a single, manual M500.

https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer

The M500 creates or saves the config override file - but with it permanently in your config, that save happens before the M501 has chance to load the saved adjustment settings!

I believe that will result in no adjustments or delta compensation at all, as it is.

Well, that didn't work. did the calibration and M500, still same.

@rjenkinsgb Okay, I will try without M500. Removed it.

I have a TEVO Little Monster Delta printer. I've been using it with a quick fix (raising the bed level on some sides). But, that kinda gets overwhelming after some time.

The problem is that the BLtouch (and I tried 3D Touch) doesn't make the fixed bed even, even with raised sides (raising the bed level basically). No matter what I do there is always a 0.4mm difference between Y-155 and Y155. Obviously, that means prints stick to the bed on Y155 side as expected while on Y-155 it prints to air. I tried to add more calibration points but that didn't fix the problem. still same.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Aug 27 2019 19:34:39 GMT+0300 (GMT+03:00)

; General preferences
G90                                                                      ; Send absolute coordinates...
M83                                                                      ; ...but relative extruder moves
G53
M665 R155 L397.19 B155 H520                                              ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                                            ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"TEVO Little Monster"                                              ; Set machine name
M552 S1                                                                  ; Enable network
M586 P0 S1                                                               ; Enable HTTP
M586 P1 S0                                                               ; Disable FTP
M586 P2 S0                                                               ; Disable Telnet

; Drives
M569 P0 S1                                         			 ; physical drive 0 goes forwards
M569 P1 S1                                         			 ; physical drive 1 goes forwards
M569 P2 S1                                         			 ; physical drive 2 goes forwards
M569 P3 S0                                        			 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   			 ; set drive mapping
M350 X16 Y16 Z16 E16 I1                           			 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E285.00‬                			 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00          			 ; set maximum instantaneous speed changes (mm/min)
M203 X36000.00 Y36000.00 Z36000.00 E1200.00        			 ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E1000.00           			 ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E1300 I30                   			 ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            			 ; Set idle timeout

; Axis Limits
M208 Z0 S1                                        			 ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                                   			 ; set active high endstops

; Z-Probe
M307 H3 A-1 C-1 D-1                              			 ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000                              			 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X20 Y0 Z0.11                                 			 ; set Z probe trigger value, offset and trigger height
M557 R155 S8                                     			 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                                              ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                                             ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8         			         ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                                             ; Set temperature limit for heater 1 to 280C
M307 H1 A310.5 C199.7 D12.1 S1.00 V19.7 B0

; Fans
M106 P0 C"Right Fan" S1 I0 F500 H-1                           		 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 C"Left Fan" S1 I0 F500 H-1                         	 	 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
 
; Tools
M563 P0 S"Extruder" D0 H1 F0:2                  			 ; define tool 0
G10 P0 X0 Y0 Z0                                   			 ; set tool 0 axis offsets
G10 P0 R0 S0                                      			 ; set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"                       ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
M500
M501                                                                     ; Load saved parameters from non-volatile memory

; bed.g
; called to perform automatic delta calibration via G32
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Thu Sep 03 2020 16:10:49 GMT+0300 (GMT+03:00)
M561 ; clear any bed transform
G28  ; home all towers
; Probe the bed at 12 peripheral and 6 halfway points, and perform 9-factor auto compensation
; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
G30 P0 X20 Y0 H0 Z-99999
G30 P1 X0 Y132.28 H0 Z-99999
G30 P2 X67.08 Y116.18 H0 Z-99999
G30 P3 X121 Y69.86 H0 Z-99999
G30 P4 X148.59 Y0 H0 Z-99999
G30 P5 X129.9 Y-75 H0 Z-99999
G30 P6 X75 Y-129.9 H0 Z-99999
G30 P7 X0 Y-150 H0 Z-99999
G30 P8 X-75 Y-129.9 H0 Z-99999
G30 P9 X-129.9 Y-75 H0 Z-99999
G30 P10 X-148.59 Y0 H0 Z-99999
G30 P11 X-121 Y69.86 H0 Z-99999
G30 P12 X-67.08 Y116.18 H0 Z-99999
G30 P13 X0 Y59.15 H0 Z-99999
G30 P14 X56.09 Y32.38 H0 Z-99999
G30 P15 X64.95 Y-37.5 H0 Z-99999
G30 P16 X0 Y-75 H0 Z-99999
G30 P17 X-64.95 Y-37.5 H0 Z-99999
G30 P18 X-56.09 Y32.38 H0 Z-99999
G30 P19 X0 Y0 H0 Z-99999 S9
G30 P20 X20 Y0 H0 Z-99999
G30 P21 X40 Y0 H0 Z-99999
G30 P22 X154 Y12 H0 Z-99999
G30 P23 X136 Y72 H0 Z-99999
G30 P24 X112 Y-106 H0 Z-99999
G30 P25 X12 Y154 H0 Z-99999
G30 P26 X0 Y-155 H0 Z-99999
G30 P27 X20 Y0 H0 Z-99999
; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)

@jay_s_uk I'm using 2.05. 3xx versions cause issues with my device so I don't use them. I don't have much time for big problems.

@jay_s_uk My web interface version is 1.22.6.

Does the new interface fix the issue?

@jay_s_uk

Thanks for your help but also didn't work.

@jay_s_uk said in Tool fan slider doesn't control all the fans:

P0:2

I tried it as M563 P0:2 S"Extruder" D0 H1 F0 but that didn't work

Hey, everyone. I have a Duet Wifi 2 with 2.05. I have an issue with the tool Fan slider. I have two cooling fans, but the tool fan slider only controls the left fan. So the right fan doesn't spin up with the tool fan slider being 100 (the fans are working alright)

Here is my fan config:

; Fans
M106 P0 C"Right Fan" S1 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 C"Left Fan" S1 I0 F500 H-1 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
; Tools
M563 P0 S"Extruder" D0 H1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

@whosrdaddy No desktop.

@bearer I'm not sure about the board. I have multiple computers in the office so the same result with them. Where can I buy that replacement diode?

My board is V1.04 I purchased it back in 2018. In the picture the board is powered by USB nothing is connected otherwise. That smoke doesn't happen with 24V (red and black wiring) but when that is connected I don't see the blue led.

I have the solder machine that I was using for my Arduino projects but It looks like I need more specialized tools for that.

After doing some experiments with smoke, I understand now. The smoke comes from the mosfet numbered "R97"

I was using my Duet Wifi 2 from 2018-2019. About a year ago, the board suddenly stopped, and after it didn't work again. It was showing VIN light when connected to 24v power. When I connect it to a USB to a computer, I can see also the blue light and the computer can detect it but smokes are coming from the USB port when it is connected to USB. Is it possible to repair this or should I get a new one? I am using the spare Duet I have with the machine.

Hey, everyone. I was seeing all the LEDs just fine. But smoke came from USB socket, didn't happen before. Any ideas?

@Veti I was using 6 factors, it was the same for that. Switched to 9 factors after. My offset is 20 btw, Y offset.

Still same.

@Veti M665 L411.422:411.422:411.422 R161.396 H523.653 B155.0 X0.335 Y-0.197 Z0.000
M666 X-0.560 Y-1.026 Z1.587 A0.20 B1.00

still having the same issue though.