@phaedrux That got it. it was such a small bend that to the naked eye it was unnoticeable. I had to get the magnifying lamp out and clamp it to the table to really look at it and it had a small bend. I appreciate it and thank you for your help. I was getting ready to just turn off the z stop and print like that tonight.

2.02 No wires are loose all of them are connected and BLTouch is responding correctly. Thats the reason it is throwing me through a loop. I cant Run a homeall sequence. it runs X and Y but not Z

Will do later today.

Hey guys having an issue I cant seem to figure out. BLTouch on my CoreXY decided to do it own thing today and I cant seem to figure out why. I printed just yesterday and it was fine. The only thing that changed was that I swapped to a V6. My config, homeall and homez are attached.

Notes :
It deploys and retracts the pin on command.
Alarm is not being triggered on the BLTouch.
Home all homes X and Y but states Zprobe already triggered at start of homing move.
Zprobe is staying at 1000 with probe deployed and retracted.

Anyone got any suggestions?
CONGFIG
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes backwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E442.00 ; Set steps per mm
M566 X1000.00 Y1000.00 Z800.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z900.00 E1200.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z1000.00 E250.00 ; Set accelerations (mm/s^2)
M906 X1300.00 Y1300.00 Z1300.00 E1300.00 I35 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X330 Y330 Z400 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 S0 ; Set active low and disabled endstops

; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H5 F100 T2000 ; Set Z probe type to bltouch and the dive height + speeds
G31 X-40.30 Y-15.77 Z1.28 P25 ; Set Z probe trigger value, offset and trigger height
M557 X35:215 Y30:195 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

HOMEALL
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
M98 Pdeployprobe.g ; deploy mechanical Z probe
G1 S1 X-335 Y-335 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 S1 X-335 ; home X axis
G1 S1 Y-335 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 S1 X-335 F360 ; move slowly to X axis endstop once more (second pass)
G1 S1 Y-335 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X180 Y180 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

M98 Pretractprobe.g ; retract mechanical Z probe

HOMEZ
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G90 ; absolute positioning
G1 X180 Y180 F6000 ; go to first probe point
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
G1 Z10 F6000 ; rapidly move the Z axis to z=10