You may need to have a look at these websites as you dont have the configerastion for the probe set up. as there is no G31 command after your M558 to say where the prob is and how to activae it.
https://duet3d.dozuki.com/Wiki/Setting_up_automatic_probing_of_the_print_bed
https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe
Just out of curiosity how do you code your Config.g?
From my understanding. you are trying to say the the Z endstop and probe is io5.in and
Do you have a z endstop and probe?
if you have both then i think you need to use diffenrt pins and codes.
I dont have the Duet 3
so cant confirem but i dont think you can use the same pin for both Z endstop and Probe.
I assumed so, but better for clarification.
Thank you so much for the time and help.
Oh awesome i somehow missed that,
Okies that makes more sense then.
Only thing i am having trouble is with the M950 S0 C"duex.e6heat"
I dont have the deux bored so i have wired it to pin 31
the wiki says it pin name is.
exp.heater7, exp.31, !duex.e6heat, !duex.pwm5
would any work or would i ahve to use exp.heater7?
Sorry for all the questions. I just like to be sure.
Oh just a thought the Z Probe Mod pin could the could i connect the yellow wire to Z Probe Mod and use M950 S0 C"zprobe.mod" instead of pin 31?
Hay all,
I thought i would give firmware 3 a go on my Duet WIFI (1.02)
and with the naming of things i just wanted to see if i have got it write.
Before i take the plunge, my main problem is the BLTouch
Using BLTouch Guide
https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/
Firmware 2
Config.g
; generated by RepRapFirmware Configuration Tool v2.0.4 on Tue Sep 24 2019 20:19:18 GMT+0100 (British Summer Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Tronxy X5s" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; Physical drive 4 goes backwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E429.18 ; set steps per mm
M566 X600.00 Y600.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z1500.00 E18000.00 ; set maximum speeds (mm/min)
M201 X3000 Y3000 Z1000 E10000.00 ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E1100 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-17:310 Y-27:310 Z0:300 ; set axis minima/Maximium
; Endstops
M574 X0 Y0 S0 ; set active high endstops
; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M307 H7 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H10 F1000 T8000 ; Set Z probe type to bltouch and the dive height + speeds
G31 P500 X37 Y-3 Z0 ; Set Z probe trigger value, offset and trigger height
M557 X5:305 Y5:305 S20 ; Define mesh grid
; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 R4700 C7.06e-8 ; set thermistor + ADC parameters for heater 1
M143 H1 S290 ; set temperature limit for heater 1 to 280C
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S255 I0 F1000 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings
M671 X-33:310 Y150:150 S10 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
; Miscellaneous
M911 S10.0 R11.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000
M501 ; load saved parameters from non-volatile memory
Firmware 3
Config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.3 on Mon Dec 09 2019 11:47:20 GMT+0000 (Greenwich Mean Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"X5s Duet" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0
M584 X0 Y1 Z2:4 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E429.18 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1800.00 E1800.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z500.00 E10000.00 ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E1100 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-17 Y-27 Z0 S1 ; set axis minima
M208 X310 Y310 Z400 S0 ; set axis maxima
; Endstops
M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; Z-Probe
M950 S0 C"duex.e6heat" ; create servo pin 0 for BLTouch
M558 P9 C"zprobe.in+zprobe.mod" H10 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P100 X37 Y-3 Z0 ; set Z probe trigger value, offset and trigger height
M557 X5:305 Y5:305 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T10000 B3988 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
; Fans
M950 F0 C"fan0" Q1000 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Part" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"fan2" Q1000 ; create fan 1 on pin fan2 and set its frequency
M106 P1 C"Tool" S0 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0:1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
Thank you all.
Ahh thank you. i was hoping that was not the case, as i have a webcam spare but not an IP cam, didn't want to have to buy a new camera. and i thought as i have micro to usb adaptors and the micro isn't used, but ah well thank you for the response
Is there a way to use the micro USB connection to use Webcam? I have a few OTG cables from old phones and thought well i can connect them but is the "firmware/Hardware" there for it to work or even a way to get it to work.
Also the speed of the z axis ,might be to fast. i had this and my z axis moved clunky but to fast.
here is a snippet from my g code
; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation
M92 X80.14 Y79.89 Z401.04 E95.83:95.83 ; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y20 Z250 E250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800:800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30
Not sure if i follow properly, You want it to wipe before the it resumes the print (before it starts printing the wall/infill)
if so couldn't you just put a move/extrude before the
:- G1 R1 X0 Y0 Z5 F6000 ; go to 5mm above position of the last print move,
like
G1 X"wipe area" Y"wipe area" Z"wipe area" F6000
G1 X"wipe move" Y"wipe move" Z"wipe move" E"extrude filament" F1000
??
@wilriker No didn't change the lead screw. but once i got stuff working. I did a re-calibration of all axis's.
Need a bit more fine tuning but 20 mm print was 20.23mm so cant complain lol.
@JoergS5 eventually I will be using one stepper, doing that. Yeah i didn't know about the spindles being off but that does make sense. I will take that into account and grab a long spindle to cut in half, well that's if i don't come across anything else to use for the z axis. (hyper-cube set up)