Posts made by Sharpie

OK I can get the system to home to the endstops but my print head stays in the back Left and does not move to the front left after homing. but on a plus note I have gotten it to move to the endstops and stop.

I have swapped my motors back to the original settings the problem I am getting now is when I home I still either dont stop when the end stop is hit or the head goes the wrong way. then when I flip the S1 to and S0 to reverse it then try to move the head the opposite axis moved instead. Does anyone have a working config I can start from so I can figure this out?

Thanks already for all your guys help

ok, with those changes I now Home correctly, Thanks =D

New problem after it is homed the print head does not move to the forward position ie..the front Left corner. It stays in the back left so when I send a print file for it it tries to move backwards which it cant as its already all the way back.

Ok so I ended up having to swap my X-axis and Y-axis motors (i did not think going from 1.18 to 1.20 would require a hardware rewire) but per the last post everything moves as it should.

The problem is still my homing files when i home x or why only that motor turns until its hits the end of the track and starts skipping teeth on the belt.

I made the changes in my Homex.g and still only 1 stepper motor moved making the print head pull to one side the front left. So i double checked my Config.g to make sure my "X -10" moved towards my endstop. I then confirmed with the Y-Axis as well. As I switched the "S1" to "S0" instead of the X-Axis moving the Y-Axis would move.

ok So I went and and made the changes and it did not do what I thought it would so I re-Tested my Direction settings

<code>; Machine configuration
M569 P0 S1 ; Drive 0 goes forwards (change to S0 to reverse it) X-Axis
M569 P1 S1 ; Drive 1 goes forwards Y-Axis
M569 P2 S0 ; Drive 2 goes forwards Z-Axis
M569 P3 R-1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards<\code>

now when I test and change my P0 from "S1" my X-axis moves to "S0" my Y-Axis moves

I feel like I am loosing it. Is there a working config I can just buy from someone?

When I send a move command the machine moves correctly the issue is that when I issue a Home command on either X or Y that only one Stepper moves and does not stop when the end stop is triggered.

Here are my current config files

3_1536536828297_homey.g 2_1536536828296_homex.g 1_1536536828296_homeall.g 0_1536536828296_config.g

So I dont have a backup of my config =(, but I am still when I send move commands it works as intended but when I Home only one of my 2 steppers move. I ran through the RepRap config file generator again and it gave me the same settings so I am not sure what to change.

Is there a setting that makes it not move both steppers as needed for CoreXY or does my machine think its in Cartesian mode when it Homes?

Would you suggest me going back down to 1.18?

I have not changed any wiring from 1.18 to 1.20 they has been only software. I have noticed though that when Homing X only 1 stepper motor moves and with my Core XY config dont both have to move?

I have these endstops and they show as triggered in the screen when I press them by hand but it takes a few seconds to register. Is that normal?

ok I made the changes, but I still get the problem when the endstop is hit the machine does NOT stop. Is there something I can put in to stop the machine.

ok thanks guys for the help. Is there a sample config I can use to get running? I am running a D-Bot that was all dialed in before the update. Is is there some changes I can make to my old config file to get it working in the new 1.20?

I just upgraded my firmware from 1.18 to 1.20 and been having a hell of a time getting the config set back up. I got the machine moving again but now when my endstops are hit the machine still does not stop.

Attached are my Config.g and my Homing files. Is there something new in this latist version that I am missing?

4_1536118102283_homez.g 3_1536118102283_homey.g 2_1536118102283_homex.g 1_1536118102283_homeall.g 0_1536118102282_config.g

I know I have a blown driver but how do I disable the error message?

I already dont use that driver anymore.

I would love this as well

Can the Duets run any version of RepRapFirmware or is it a Custom flavor just for the Duet hardware?

Full disclosure I am still looking, and in the planning stages of the project and getting parts lists together. I would like to use another DuetWiFi but need to make sure I can before I go full swing into another one. Does the DuetWiFi firmware Mirror the RepRapFirmware?

Thanks for the help.

is there a way to set the firmware to take CNC .gcode as apposed to 3D printer .gcode? I am looking to build a MPCNC and after adding a DuetWiFi to my D-Bot (Which made it 100x better) I wanted to do the came with the MPCNC.

Is this something the DuetWiFi can do? Do I need a special Firmware?

Thanks for the great work guys =D