@gloomyandy said in RepRap Firmware Issue in behavior:

M98 P"config.g"

Hi @gloomyandy I appreciate your help on this below the outcome of M98P "Config.g", I agree with you some information might be strange in my Config.g file like the S because I added it without exact knowledge of the functionality so I thought that might Improve the result. but i do not know the actual value I should add :).

Actually this is an old project i never finish as not dedicated to however since i am working on again i would like to know how should i move on below is a picture of the machine as i was not able to upload video due to the size

I uploaded while the machine in action however if you notice that the circle is not exactly circle it looks like defected circle you can tell however in the square it is more clearer

9/26/2022, 12:21:35 AM M98 P"config.g"
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is disabled
Error: bad grid definition: Too many grid points; suggest increase spacing to 58.4mm
9/26/2022, 12:17:55 AM M122
=== Diagnostics ===
RepRapFirmware for LPC176x based Boards (biquskr_1.4) version 3.2_4 running on LPC176x at 100Mhz
Used output buffers: 1 of 16 (11 max)
=== RTOS ===
Static ram: 4956
Dynamic Memory (RTOS Heap 5): 7896 free, 7856 never used
Allocations: 178 Frees: 21
Never used RAM 256, free system stack 14 words
Tasks: NETWORK(ready,187) HEAT(blocked,243) MAIN(running,354) IDLE(ready,21)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:25 ago, cause: [software]
Last software reset at 2022-09-26 00:16, reason: User, GCodes spinning, available RAM 256, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0042a000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Supply voltage: under voltage events: 0
Driver 0: position 0, standstill, SG min/max 0/10, error r/w 0/1, ifcnt 73, cnt r/w 7165/15, timeout 0, failedOp 0xff
Driver 1: position 0, standstill, SG min/max 0/0, error r/w 0/1, ifcnt 68, cnt r/w 7168/12, timeout 0, failedOp 0xff
Driver 2: position 0, standstill, SG min/max 0/18, error r/w 0/1, ifcnt 73, cnt r/w 7165/15, timeout 0, failedOp 0xff
Driver 3: position 0, standstill, SG min/max 0/0, error r/w 0/1, ifcnt 63, cnt r/w 7169/11, timeout 0, failedOp 0xff
Driver 4: position 0
Driver 5: position 0
Driver 6: position 0
Date/time: 2022-09-26 00:17:51
Slowest loop: 20.93ms; fastest: 0.13ms
Step timer: target 34955404 count 84948299 delta -49992896 late 0
USBSerial connected 0
ADC not ready 2 ADC error threshold 10 ADC Init 1
Ints: 51516; Calls 51516; fast: 3uS; slow 20uS adj 0 bad 0 big delta 0
PWM Channels
Delta -822796941 Start -1 End -1
=== Storage ===
Free file entries: 6
SD card 0 detected
SD card longest read time 2.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 40, maxWait 20302ms, bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves 7, completed moves 7, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0, chamberHeaters = -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 42.51ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0)
HTTP sessions: 1 of 2

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25-01LE-D
WiFi MAC address c0:56:27:45:b2:f9
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 35944
WiFi IP address 192.168.1.134
WiFi signal strength -68dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00181001
Socket states: 0 0
Untitled.jpg20220926_230657.mp4