Posts made by rowow

@phaedrux thanks alot, after some searching around in the router settings I managed to find the mac address and set it. Originally the entire reason I wanted to set the address manually is because of my new router the printer ip doesnt show up in the client list for whatever reason. There was a mac address in the client list that wasnt in the ip list which I assumed was the printer and worked. Before I had to check it each time via a usb cable. Thank you

@phaedrux this is exactly what I followed. Ive been using my duet for a few years now and just now decided to put it on a stable ip.

@norder Hello as the title says this is wifi not ethernet

@phaedrux I am using yat via USB terminal yes. I sent M122 and got the following
"=== Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later<LF>Board ID: 08DJM-9178L-L2MSD-6JTD2-3SN6K-KTHQR<LF>Used output buffers: 1 of 24 (23 max)<LF>=== RTOS ===<LF>Static ram: 23876<LF>Dynamic ram: 75180 of which 176 recycled<LF>Never used RAM 12328, free system stack 114 words<LF>Tasks: NETWORK(ready,65.2%,231) HEAT(delaying,1.4%,314) Move(notifyWait,4.8%,313) MAIN(running,27.0%,441) IDLE(ready,1.6%,29), total 100.0%<LF>Owned mutexes: WiFi(NETWORK) USB(MAIN)<LF>=== Platform ===<LF>Last reset 19:39:04 ago, cause: power up<LF>Last software reset at 2022-06-28 20:45, reason: User, GCodes spinning, available RAM 12328, slot 1<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a<LF>Error status: 0x00<LF>Step timer max interval 0<LF>MCU temperature: min 37.8, current 38.0, max 48.9<LF>Supply voltage: min 0.0, current 24.0, max 24.2, under voltage events: 1, over voltage events: 0, power [Warning: Maximal number of characters per line exceeded! Check the line break settings in Terminal > Settings > Text or increase the limit in Terminal > Settings > Advanced.]"

When I enter
"M552 S1 P192.168.1.14"
I get the following in response
"Error: M552: expected string expression<LF>ok<LF>"
I am running version 3.3
Not sure if im doing something wrong or if this is a glitch.

@deckingman I appreciate that was more of what I was looking for. I am aware of the risks and am not worried about that. Ill try tweaking around with the parameters more in the upcoming days

@siam M308 gives a error of "sensor number out of range"
my H0 is the bed, and H1 is the extruder.

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 10:18:18 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"My Printer"                             ; set printer name

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E220.00              ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E1500                   ; set motor currents (mA)
M84 S0                                         ; Disable motor idle current reduction

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X300 Y300 Z220 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P5 C"^!zprobe.in" H5 F120 T6000              ; set Z probe type to switch and the dive height + speeds
G31 P500 X45 Y-12 Z3
M557 X30:260 Y15:300 S20

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M307 H0 A100  ; Heater Bed Temp Setting to avoid heating too slow error
M307 H1 A100 C302 D5.8 B1  ; Heater Extruder Temp Setting

M143 H1 S420 ; extruder max temp

@siam Yes I did the PID tuning. Ill be honest I might have missed something so just to be sure I did it right here is what I did:
1: type "M303 H1 S240" in console
2: type "M303" in console
3: Copy results
4: Post results at the end in #config

I am using a duet wifi
firmware 3.2

@t3p3tony I tuned the heater however there are two fundamental flaws with the duet software
1: Any sort of environmental change such as difference in temperature or a fan turned on will cause the firmware to fault due to "heating too slowly". Why is this setting set so tight is beyond my understanding.
I have been able to fix this problem by changing the heating parameter

2: I upgraded to a volcano hotend and the temperature delay is somewhat significant and even though it shuts off the heater the temperature still rises and a "temperature exceeds 15c" error comes up. idk what the issue with this is and am simply frustrated with the countless problems I am getting with this board.

If you have any suggestions I would be glad to hear, otherwise im about to throw away this junk controller.

Ive already burnt my fingers significantly trying to change some things to figure out the problem and am very frustrated with this entire platform. I am about to return back to a ramps board as the duet software is the biggest missed opportunity and loaded with so much crap. seems like nothing can be made with quality anymore and every single little thing needs to be DIY'ed.

How do I disable all heater fault failures

@phaedrux I reinstalled the files on the SD card and that seems to have fixed the issue. Not sure what was wrong with the card. Thank you.

Hello ive been using this printer for months now without issue. Then randomly yesterday I stopped being able to connect via the web interface. It loads up and shows the typical GUI but the status on the top left is a grey "disconnected" and all the buttons dont work. Ive tried power cycles, trying on different browsers, trying on different devices, and nothing works. Im not sure how to proceed from here. I havent tried to connect via USB due to it being in a difficult location, but if I have to then I can get some long USB cables.

@Phaedrux Thank you so much! It finally works. Would be nice if they had all this simply on the wiki. Is there any proper place I can search for information or is the forums the only place. I think thats all for now but in the future it would be nice to have a up to date source of information.

Thank you, adding the following code has allowed the Z probe to start working. When the induction probe is in front of metal it reads 0 when not it reads 1000.

However now when trying to home the Z axis it says "error z probe already triggered"

No diode though as the wikipedia states it doesnt need one for my board version
"Duet 3, Duet 2 Maestro, or revision 1.04 or later of Duet 2 WiFi or Duet 2 Ethernet: you can connect the output of the sensor directly to the Z-probe IN pin."

@Phaedrux

I wired it directly as the wiki stated without the diode to the z probe connection. please see the attached photo for clarification

What do I need to put in for the G31 command

homeall.g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 10:18:18 GMT-0400 (Eastern Daylight Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-235 Y-215 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-235 Y-215 F360  ; move slowly to X and Y axis endstops once more (second pass)
G90                     ; absolute positioning
G1 X15 Y15 F6000        ; go to first bed probe point and home Z
G30                     ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

Results of M122 and M98:

5:00:20 PMM98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
5:00:08 PMM98



![Captddure.PNG](/assets/uploads/files/1607637956781-captddure.png) 
4:59:59 PMM122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2-beta1 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1D6-3S86N-KAX6Z
Used output buffers: 3 of 24 (6 max)
=== RTOS ===
Static ram: 23916
Dynamic ram: 98916 of which 44 recycled
Exception stack ram used: 256
Never used ram: 7940
Tasks: NETWORK(ready,221) HEAT(blocked,308) MAIN(running,456) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:07:55 ago, cause: power up
Last software reset at 2020-12-09 17:14, reason: User, GCodes spinning, available RAM 7924, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0x020
MCU temperature: min 21.9, current 24.4, max 24.9
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2020-12-10 16:59:58
Cache data hit count 838659451
Slowest loop: 6.57ms; fastest: 0.15ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.4ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 14.24ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address f4:cf:a2:69:53:26
WiFi Vcc 3.36, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 15616
WiFi IP address 192.168.1.132
WiFi signal strength -50dBm, reconnections 0, sleep mode modem
Clock register ffffffff
Socket states: 4 0 0 0 0 0 0 0

I am trying to get a inductive z probe set up however it reads 1000 on the web interface and when trying to home is says "Error no z probe" I followed the wiki guide "https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe" and directly wired it to the z probe input. I triple checked the wired and they are all connected and working with a multimeter. Ive tried going through dozens of posts online and each one says something completely different to another and cant find any tutorial on what exactly I need to have in my config.g for this to work.

Can someone please help a idiot like me and tell me exactly what I need to do to get this working. I have been on this board for over 2 months now trouble shooting all the issues its been giving me. I am pretty disappointed though with this last problem I hope I can finally have a fully functional setup.

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Oct 03 2020 10:18:18 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"My Printer"                             ; set printer name

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E220.00              ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1000 E1500                   ; set motor currents (mA)
M84 S0                                         ; Disable motor idle current reduction

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X230 Y210 Z200 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z

; Z-Probe
M574 Z0 P"nil"
M558 P5 C"zstop" H5 F120 T3000                         ; set Z probe type to switch and the dive height + speeds

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M307 H0 A100  ; Heater Bed Temp Setting to avoid heating too slow error

M143 H1 S420 ; extruder max temp