@bettodiaz hii yes now ihave tock fun only the board fun i change
this my config
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X79 Y79 Z396 E408 ; set steps per mm
M566 X1000 Y1000 Z24 E2500 P1 ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z900 E6000 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X688 Y688 Z688 E810 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X235 Y235 Z240 S0 ; set axis maxima

; Endstops
M574 X1 Y1 S1 ; set active high endstops
M574 Z1 S2 ; set endstops controlled by probe

; Filament runout sensor ;Filament run-out sensor triggers a pause
M591 D0 P2 C3 S1

; Z-Probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H2.5 F350 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-40 Y-12 Z9.562 ; set Z probe trigger value, offset and trigger height
M557 X30:220 Y30:220 S40 ; define mesh grid

; Heaters
M305 P0 T98801 B4185 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S100 ; Set temperature limit for heater 0 to 120C
M305 P1 T98801 B4185 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S250 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0.8 I0 F20 H1:0 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"hotend" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Pressure Advance
M572 D0 S0.35

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory
T0 ; Select first tool

; BLTouch startup
G4 S2 ; Pause a couple seconds
M280 P64 S160 ; Clear any alarms
G4 S2 ; Pause a couple seconds
M402 ; retract pin just in case

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

duet 2 wifi Always Disconnecting from a wifi how can ifix it ? thnks for the help
this is my g code and m122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9FL-3SN6L-9S9RR
Used output buffers: 3 of 24 (17 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93220 of which 0 recycled
Exception stack ram used: 464
Never used ram: 11676
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3752) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 01:19:00 ago, cause: software
Last software reset at 2020-10-14 19:01, reason: Hard fault, spinning module GCodes, available RAM 11552 bytes (slot 3)
Software reset code 0x4033 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x0441f803 BFAR 0x3523e3a1 SP 0x200046dc Task 0x4e49414d
Stack: 0041b6ab 00400576 61000000 7fe00000 00000000 00000000 3ff00000 00000000 404e0000 000007ff 0044c49b 00452d34 21001400 2000ba94 2000a0a4 00000000 00000000 200134e8 0041baf1 00000001 2000bba4 2000a0a4 2000ba90
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 40.0, current 42.6, max 44.4
Supply voltage: min 23.9, current 24.3, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/284
Driver 1: ok, SG min/max 0/270
Driver 2: standstill, SG min/max not available
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2020-10-14 20:20:31
Cache data hit count 4294967295
Slowest loop: 5.05ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 156, MinFreeDm: 151, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 18391, completed moves: 18370, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G0 F13200 X59.417 Y137.482" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 200.23ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 2
WiFi firmware version 1.23
WiFi MAC address XXXXXX
WiFi Vcc 3.32, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 23152
WiFi IP address XXXXXXX
WiFi signal strength -74dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

my gcode

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jun 14 2020 01:09:58 GMT+0300 (שעון ישראל (קיץ))

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Ender 3 Pro BLV"                            ; set printer name


; Network
M551 P"XXXXX"                                   ; set password
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S0                                         ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X79.56 Y79.64 Z400 E415	                       ; set steps per mm
M566 X600.00 Y600.00 Z24.00 E2000                  ; set maximum instantaneous speed changes (mm/min) (Jerk)
M203 X6000.00 Y6000.00 Z300.00 E5000.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000               ; set accelerations (mm/s^2)
M906 X700 Y700 Z700 E660 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S10                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X245 Y210 Z240 S0                  ; set axis maxima

; Endstops
M574 X1 Y1 S1                                      ; set active high endstops
M574 Z1 S2                                         ; set endstops controlled by probe

; Z-Probe
M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch
M558 P9 H3 F320 T90000                             ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X38.2 Y0 Z0.980                            ; set Z probe trigger value, offset and trigger height
M557 X40:235 Y20:225 S30                            ; define mesh grid

; Heaters
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4092 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S90                                        ; set temperature limit for heater 0 to 80C
M305 P1 T100000 B4092 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S270                                       ; set temperature limit for heater 1 to 250C


; Fans

M106 P0 A22 S0 I0 F100 H-1                          ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0  H1   T45                             ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on


; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Pressure Advance
M572 D0 S0.05		

; Retraction
M207 S0.80 R0.0 F3000 T1800 Z0.0 

; M207: Set retract length
	; Parameters
	; 	Snnn positive length to retract, in mm
	; 	Rnnn positive or negative additional length to un-retract, in mm, default zero
	; 	Fnnn retraction feedrate, in mm/minMiscellaneous

M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; BLTouch startup
G4 S2							; Pause a couple seconds
M280 P64 S160						; Clear any alarms
G4 S2							; Pause a couple seconds
M402							; retract pin just in case

@Veti ok thnks for your help

@Veti

@Veti hi clean the nozzle with a brush I put aside on x245
if ido M557 X40:220 Y20:225 S30
no its work good no error its ok ?
26.9.2020, 18:34:28 G32
49 points probed, min error -0.347, max error 0.734, mean 0.164, deviation 0.288
Height map saved to file heightmap.csv

@Veti thnks its blv ender 3
itray this M557 X40:245 Y20:225 S30 and it goo out of the bed

@Veti this is my problem ido home all
After it g29 and its not start from x0 it dont go all to the end stop
I upload to you tube https://youtu.be/7FL0kCXGIHM

ihave dde direct drive kit this is th right X Y OFFSET ,
but iget this error
Warning: Skipping grid point (0.0, 160.0) because Z probe cannot reach it
Warning: Skipping grid point (0.0, 200.0) because Z probe cannot reach it

@Veti now the speed work good thanks but ihave Another problem is it never starts from point X0 it always moves a bit to the side and starts doing bed calibration how ifix it ,You spot something wrong in my
config settings

@Veti ok thnks now its work I had to add a lot of speed to see change in tnnn

itray to change Tnnn i don't see different,
what about the z speed ?