Dear Community
My name is Daniel 28years old and technically very interested.
I've been building my printer for a while now. Unfortunately the result of the Duetwifi is not yet satisfying. For some reason the interpolation doesn't work
. If I set the micro steps with the command "M350 Y16 I1", then I hear no difference to 16x I0 also 32x 64x 128x 256x sound no different when moving.
I use the following motors:
https://en.nanotec.com/products/476-st4209l1704-a/
https://en.nanotec.com/products/460-st4209s1006-a/
Could you please tell me why?
Here are my complete settings:
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Network
M552 S1 ; Enable network
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes backwards
M350 X128 Y128 I0 ; Configure microstepping without interpolation
M350 E16:16 Z16 I1 ; Configure microstepping with interpolation
M92 X1284 Y1284 Z1285 E464:464 ; Set steps per mm
M566 X1500 Y1000 Z1500 E10000:10000 ; Set maximum instantaneous speed changes (mm/min)
M203 X8000 Y8000 Z500 E18000:18000 ; Set maximum speeds (mm/min)
M201 X800 Y800 Z40 E600:600 ; Set accelerations (mm/s^2)
M906 X540 Y1350 Z800 E950:950 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S10
; Axis Limits
M208 X-34 Y0 Z0 S1 ; Set axis minima
M208 X202 Y195 Z275 S0 ; Set axis maxima
; Endstops
M574 X1 Y1 S0 ; Set active low endstops
; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F300 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X15 Y-20 Z2.15 ; Set Z probe trigger value, offset and trigger height
M557 X0:210 Y0:165 S20 ; Define mesh grid
; Heaters
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S350 ; Set temperature limit for heater 1 to 350C
M305 P2 T100000 B4725 C0 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S350 ; Set temperature limit for heater 2 to 350C
; Fans
M106 P0 S0 I1 F500 H1:2 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S0 I1 F500 H1:2 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I1 F500 H1:2 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P1 D1 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P0 D0 H2 ; Define tool 1
G10 P1 X30 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
; Automatic saving after power loss is not enabled
; Custom settings are not configured
If you need anything else to help me, just say something.
Thank you very much in advance for your help.