@mfs12 I appreciate the improvement potential, but is there any way for me to resolve this issue on my end? I just don't know what to do with my paneldue now, since it doesn't receive information it seems to be little better than a paperweight.

@mfs12 The console tab doesn't display anything, even if I do send commands to the board via the PanelDue. The PanelDue reports "Connecting"

thx

Thanks for the replies, I did some more reading, and replaced the cable with a shorter one (4 feet before to 6 inches or so now). I tested the current cable and it looks good, but the issue still persists (can still send commands but stuck connecting). On the off chance I had a bad wire again I swapped the UTXD - DIN wire with the URXD - DOUT wire on the terminals and tried again, but the same problem happens. I looked at some of the traces on the duet and the paneldue, but nothing looks obviously amiss.

Right, thanks a ton for waiting lol.

The output of the M115 command is as follows:

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-06-15 21:45:03

My config file is as follows:
.
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue May 25 2021 23:51:34 GMT-0500 (Central Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"*****" ; set printer name

; Network
M551 P"*****" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1590.00 E420.00 ; set steps per mm
M566 X90.00 Y90.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X8000.00 Y8000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X50.00 Y50.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1100 Y2200 Z800 E700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X640 Y540 Z1000 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"!zstop" ; configure active low endstop for low end on Z via pin zstop
; M574 Z1 S2 ; configure z to use a probe at the min

; Z-Probe
;M558 P9 C"^zprobe.in" H3 F100 T2000 ; specify probe and input pin, also enable pullup resistor
;M557 X15:20 Y15:195 S20 ; define mesh grid
;G31 P100 X10 Y10 Z2 ; define offset and sensitivity for bltouch
;M950 S0 C"exp.heater3" ; create servo pin index

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"pt1000" ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H3 A-1 C-1 D-1 ; unbind heater pin 3 for use in bltouch

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P1 D0 H1 F1 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue

I'm still learning a lot, so let me know if I've botched the configuration.

Thanks

@phaedrux Thanks for the help, I'm going to flash the paneldue firmware to 3.3 RC3 and check up on it.

The problem i'm facing with the paneldue is that it boots up, shows me the logo, and then displays the 'connecting' status in the upper right hand corner, as if it's not receiving any data from the duet.

It should be noted that I can home axes from the paneldue, but that appears to be all I can do. I can't heat the extruder.

The cable is one I got with one of my stepper motors that I terminated with the connectors I got with the duet. I've checked the continuity and wire configuration of the cables multiple times, everything is as presented in the paneldue guide.

I'll follow up on this soon, I've got a fairly long job on the printer at the moment, I'd like to try everything you suggested before I ask for any further help.

Again, thanks a million for any help,
RBIII

Hey there,

I'm having some persistent issues with my paneldue 7i. I updated my Duet 2 Wifi with RRF 3.2.2 a bit ago, and installed the PanelDue, where it did not work. I did a little reading and worked on updating the firmware via bossa with version 3.3.0-rc3. Everything worked correctly, but the PanelDue wouldn't complete a connection with the Duet. I'm using the 4-pin connectors on both the PanelDue and the Duet. I feel like listing what I've attempted would help, so here goes;

1. checked continuity of the 4-pin cable (it works)
2. included the M575 P1 S1 B57600 command (tried with other values for Snnn, also tried omitting the command altogether)
3. Triple-checked the connections with pictures on the paneldue guides (https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update)
4. installed an older firmware (3.2.0, checked also with the chip on the board with release 3.2.0, mine has ATSAM 4S4B)
5. Attempted to update that firmware to 3.3.0 following the paneldue guide steps
   The following error message appears
   Error: Failed to communicate with PanelDue bootloader (no START signal received). Please try again or press the Erase and Reset switches on
   PanelDue.
6. Went round and round a couple times with the erase and reset button and tried the command multiple times
7. Reinstalled the 3.3.0 paneldue firmware to the paneldue via bossa with the erase and reset procedure (with verification)
8. Checked the terminals for burns, scratches, blown out caps, etc. basically anything that looked like it shouldn't be there.

I try to read up and fix things myself, but I'm getting to the end of my rope here? Have I missed something obvious, or do I have something faulty? Thx for any help at all in advance

(PS I'm not sure why it only allows me to select 'plugins for DWC and DSF category')