Posts made by Rattlemycage

It was working correctly on one board but the Z motors would not operate. replacing the board brought the Z motors into play but lost the X

Have tried 3 cables and 4 stepper motors. Still the same, vibration but not turning.

Hi, I replaced the stock board in a Chiron for a Duet2 WiFi. No matter what I did, I could not get the Z motors to turn, they would only vibrate. I had a second board so I just replaced it. Now the Z motors work but the X motor vibrates and moves in both directions for a few centimetres. I used the same SD card with each board. What am i doing wrong?
Thanks

Found it guys, Thank you for all your assistance. The connector had come away from the endstop. All working great again now.

Additionally. when trying to home from the paneldue the head is moving about 10mm each time i press it AWAY from the home position.

G1 H1 X-305
G1 H2 X5
G1 H1 X-305 F360
G1 H1 X-305
G90

Hi, Machine has been running fine no problems. Finished a print and found the head was at the far right of the X axis, the limit switch is on the left.
When trying to home the X, I get an error message "Error bad command"

Manual move via the Paneldue will move the X away from the endstop but not more than a single movement towards it.

I replaced the micro sd card with 3 different working backups that were all previously checked and confirmed working ,but the problem still persists.
Any help would be appreciated.
Thank you.

Thank you for all your assistance. I feel rather embarrassed to ask for more.
I have the settings for my machine.

Printing Acceleration 1000.00 mm/s2
Retract Acceleration 3000.00 mm/s2
Travel Acceleration 1000.00 mm/s2
Max Acceleration X 9000.00 mm/s2
Max Acceleration Y 9000.00 mm/s2
Max Acceleration Z 100.00 mm/s2
Max Acceleration E 10000.00 mm/s2
Max Jerk X/Y 12.00 mm/s
Max Jerk Z 0.40 mm/s
Max jerk E 5.00 mm/s

How do i put these values in my config.g please?

Thank you

@Rattlemycage, It is seemly random. On a single layer of an object perimeter, say 4 inches by 5, it might actually come to a stop 7 or more times. I tried to upload a video but my files are larger than the 4mb permitted.

I increased the speed. without success. Still stopping. What am I missing guys?

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E415.00:415.00 ; set steps per mm
M566 X900.00 Y900.00 Z200.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z2000.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z250.00 E250.00:250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E700:700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S10 ; Set idle timeout

; Axis Limits

I am printing the file via the Duet Web Control 2.0.4

The slicer is Simplify3D.

When the head stops it leaves small blobs of filament.

Thank you so much for your assistance.

I am not using using bed mesh compensation. What speeds do you suggest i take my Z Jerk and Accel ?

More so how do I alter it?

Thank you.

My config-override.g

; config-override.g file generated in response to M500 at 2020-04-20 11:32
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 A97.1 C417.0 D1.8 S1.00 V23.2 B0
M307 H1 A394.1 C133.8 D6.7 S1.00 V23.9 B0
M307 H2 A282.8 C108.3 D6.7 S1.00 V24.0 B0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

My Config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 17:50:46 GMT+0700 (Indochina Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"NEW Raise N2" ; set printer name
M564 H0
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E415.00:415.00 ; set steps per mm
M566 X900.00 Y900.00 Z22.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z280.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z40.00 E250.00:250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E700:700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S10 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z300 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P0 H5 F120 T9000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"pt1000" R4700 ; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M140 H0 ; map heated bed to heater 0
M308 S1 P"spi.cs1" Y"rtd-max31865" ; configure sensor 1 as thermocouple via CS pin spi.cs1
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280
M308 S2 P"spi.cs2" Y"rtd-max31865" ; configure sensor 2 as thermocouple via CS pin spi.cs2
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M143 H2 S280 ; set temperature limit for heater 2 to 280C
M501

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 S"HOTEND1" D0 H1 F0:1 ; define tool 0
M221 S100 D1
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"HOTEND2" D1 H2 F0:1 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
;M563 P2 S"HOT2" D1 H2 F0:1 ; define tool 2
;G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
;G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501

Hi all, I have a problem with the head stopping for a second or so about every minute or less depending on the size of the object being printed. All my other printers are a fluid motion, this Duet2 WiFi one appears to be jerking and stopping and starting.
Any assistance would be greatly appreciated.
This is the Diagnostics log.
Thanks

M122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MSD-6J9DJ-3S86L-TBD2N
Used output buffers: 3 of 24 (9 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 92320 of which 0 recycled
Exception stack ram used: 560
Never used ram: 7676
Tasks: NETWORK(ready,648) HEAT(blocked,1240) MAIN(running,3676) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 03:12:43 ago, cause: power up
Last software reset at 2020-06-16 21:09, reason: User, spinning module GCodes, available RAM 7724 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 15.5ms, max retries 0
MCU temperature: min 34.7, current 60.6, max 61.2
Supply voltage: min 22.8, current 24.0, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/196
Driver 1: ok, SG min/max 0/186
Driver 2: standstill, SG min/max 9/190
Driver 3: ok, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-06-22 11:44:03
Cache data hit count 4294967295
Slowest loop: 94.97ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 139, MinFreeDm: 115, MaxWait: 680005ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 317506, completed moves: 317466, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X145.982 Y198.556 E2.9964" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 157.86ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address bc:dd:c2:57:ad:c0
  WiFi Vcc 3.34, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 26104
  WiFi IP address 192.168.1.101
  WiFi signal strength -70dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

Thank you so much.

I recently upgraded a machine with a Duet2 Wifi. For the last few days, when on a long print I sometimes lose the wifi connection.
The blue LED is lit but my computer will not connect. It is sometimes listed on the router but not always.
I have the Paneldue and wonder if a macro could be made to reset the wifi. Thanks.