Posts made by rajilpahuja

@dc42 And what about the 10 pin cable ? how long can it be ? and does using it also effect the pt100 daughter board ?

hi, need help with what ribbon cable lengths will be ok to use on the e3d tool changer, i mean the 10 pin one, read 400mm is max out, but for the tool hcnager i reckon i need 600 or 700mm so can that long a cable be used ?, also is it ok to use a pt100 board with a longer ribbon cable ? and for the normal cables i read somewhere u cant use the sd card slot if u use them on the panel due, however do the other functions work ? wasn't mentioned, any clarity on that,

@zapta my guess is sometimes you can get faulty boards or drivers, electronics are after all not a 100% all the time, or it could be a wiring thing from the @E3D ppl, anyways i will have to investigate this, and hopefully i get a replacement

Good news is that after adding the R-1 the alarm went away, now i must inspect all the wires to be very sure before plugging them in :), but hope i get a replacement

@bearer i think i should have but generally i never had issues with their stuff, so was relaxed on the checking part, but i guess need to check even if its from the most dependable companies

@bearer ok will try this to see if error goes

@bearer the line there says M569 P3 S0, so i need to add like this M569 P3 S0 -R1 ?

@bearer strangely the wiring came from E3D so i am perplexed how they would have messed it up

@bearer i didnt try that as yet but, i can try that and see , firstly i think want the alarm gone, cause those keep coming

@bearer where can i M569 this, in the config.g , just asking cause i am new to the duet, but have expeirence with other printer boards, also i tried to swap the ports from 3/4/5/6 to 7/4/5/6 that didnt get the alarm silent as well

@dc42 also a heads up, i tried swapping the ports in the config.g as i had seen someone do on the duet3d forum but still the alarm persists, strangely i can home the machine, pick and drop tools, fans work too, and i can heat the tools and the bed, hopefully you have some solution to this

My Apoligies, i sent the video link and not the picture link, below is the picture link

https://p17.zdusercontent.com/attachment/1210792/Fg6pOrlOXEGI6ZlpYImVmgBn2?token=eyJhbGciOiJkaXIiLCJlbmMiOiJBMTI4Q0JDLUhTMjU2In0..FEoVv_Apan8wIxzvIuHHxw.tmH7IYQIfsThPNV9URfgC72_9xqypNjOciMh0LTNFVwPiRPZ1xBqIg9pAg-j9dHykjQYEzig6Jk_HOyGT4RXvYwxAg-j0RlekHAdlCaeGgJhF7hjqiye0j5gxnDNiGVAE3os-riuA2g5nPptL_btJrQNFulPS7XPlRaNf1wa_c2gExzIAL52Ak68Hh0IaaSUOsJcvkR7xcTXrzglqzJZKTZFJ9Z4DshS9St3nYvibhZZUbBkkFSP_2vCwUCwQhNbsZJHAnSfwqgELaKj70E1WrnGHezg5_Je24EqtC8Unzc.tyR3kLJEGkMMlK5gpzCrVw

Hi,

I had bought the tool changer, and i was installing it, went through the wiring and commissioning after i moved to try a test print as suggested, and it started and we were printing without any filament, just to test the motion, but then i got a alarm, and a some sparks on the board, the alarm was and is still not going is “short to ground reported by 3 driver(s) over temperature shutdown reported by 3 Driver(s)” i am enclosing a pic of the same, i read online that some duet boards might have a fault and that they are replaced in warranty if this error happens, please help me out here on this, i tried removing all the steppers and it still gives this alarm, however i can home and pick up tools even the fans work, so please help me out here as what to do next, Thanking you

https://p17.zdusercontent.com/attachment/1210792/OAAl1Va48TE5nfDLSLP8SUuXy?token=eyJhbGciOiJkaXIiLCJlbmMiOiJBMTI4Q0JDLUhTMjU2In0..gvHQnZ0I3r92dmOP6QCgJw.KbmJPgbkkPQKbXVLzj9sD6hbXpMXDa0hZZSi5-MJ4abTCh3SZ_2BDN8zwjQUB2AN_WUciTLNUTU-2kYnVSueBb6yV_WyKJ9oegoDCQIHNSG1-ii8LAkllvHQvW5iITxN1nyE5cWtQm60z1VSmor986JxGVqLveysQGZFJhA9su2mv9MoKUIzHU5mOy1RfpdoMpWl3CFlHNK5O85G184YamF3T_1ua1w3HXqsjxticIfa38XJ41N8FfgPOyId5O6qoQYzME4uJjvKaaumnUZEGciZQmo_GDZsewLBwUFSPks.R6sTRTfCWv9JD1xTpqacxQ