Posts made by rafpv

undefined

@jay_s_uk thank you. Found my mistake. It's amazing what happens when I read ALL the directions and not just skim over them.

undefined

Hi all.
I can't get 2nd tool/heater to control any fan at all. Seems that tool1 is turning on both fan 1 and 2 at 80C. I tried mapping 1st fan to 2nd tool and it doesn't even come on. Tried removing F1 from completely from tool 1, that just leaves no fans coming on at 80C. I realize by default tool 1 controls fan 1 and 2. How do I give fan 2 control over to tool 2 only?
Thank you in advance.

; Configuration file for Duet 3 MB 6HC (firmware version 3.3)

; Drives
M569 P0 S0		                                         ; physical drive 0.0 goes backwards
M569 P1 S1                                             ; physical drive 0.1 goes forwards
M569 P2 S0                                             ; physical drive 0.2 goes backwards
M569 P3 S0                                             ; physical drive 0.3 goes forwards
M569 P4 S0                                             ; physical drive 0.4 goes forwards
M569 P5 S0                                             ; physical drive 0.5 goes forwards
M584 X0 Y1 Z2:3 E4:5                         			; set drive mapping

M350 X16 Y16 Z16 E16:16 I1 								; configure microstepping with interpolation
M92 X80.00 Y100.00 Z400.00 E402:402 					; set steps per mm
M566 X900.00 Y900.00 Z50.00 E900.00:900.00 P1 			; set maximum instantaneous speed changes (mm/min)
M203 X4000.00 Y4000.00 Z2000.00 E4000.00:4000.00 		; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E2500.00:2500.00		; set accelerations (mm/s^2)
M204 P600 T800 											; set printing ans travel accelerations (mm/s^2)
M906 X1200 Y1200 Z1100 E1100:1100 I30 					; set motor currents (mA) and motor idle factor in per cent
M84 S30 												; Set idle timeout

; Axis Limits
;M208 X-10:410 Y0:410 Z0:810 ;U0 S1 ; set axis minima
M208 X410 Y410 Z410 U210 S0 ; set axis maxima
M208 X-10 Y0 Z-10 S1 ; set axis minima
;M208 X410 Y410 Z410 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"!io4.in"                                     ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io0.in
M574 Y1 S1 P"!io1.in"                                     ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io1.in
M574 Z2 S1 P"io2.in+io3.in"                               ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin io2.in
M591 D0 P1 C"!io6.in" S1 								  ; simple sensor (high signal when filament present) connected to IO_4 for drive 0, enabled
M591 D1 P1 C"!io8.in" S1 								  ; simple sensor (high signal when filament present) connected to IO_4 for drive 0, enabled

; Extruder servo
M950 S7 C"io7.out" Q400									 ; assign IO port 1 to out7 (Servo header), servo mode
M42 P7 S1 											 	 ; set 100% PWM on GPIO port 0

; Z-Probe
M950 S0 C"io5.out"                                       ; create servo pin 0 for BLTouch
M558 P9 C"io5.in" H5 F120 T6000                          ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z0.76                                      ; set Z probe trigger value, offset and trigger height
M557 X15:365 Y15:375 S20                                 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138             ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                       ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                         ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                  ; map heated bed to heater 0
M143 H0 S120                                             ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"pt1000"                               ; configure sensor 1 as PT1000 on pin temp1
M950 H1 C"out1" T1                                       ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                             ; set temperature limit for heater 1 to 280C
M308 S2 P"temp2" Y"pt1000"                               ; configure sensor 2 as PT1000 on pin temp2
M950 H2 C"out2" T2                                       ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                             ; set temperature limit for heater 2 to 280C

; Fans
M950 F0 C"out7" Q500
M106 P0 H-1
M950 F1 C"out8" Q500                                     ; create fan 0 on pin out8 and set its frequency
M106 P1 T80 H1                                           ; set fan 0 value. Thermostatic control is turned on
M950 F2 C"out9" Q500                                     ; create fan 1 on pin out9 and set its frequency
M106 P2 T80 H1                                          ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"hotONE" D0 H1 F1								 ; define tool 0
G10 P0 X0 Y0 Z0                                          ; set tool 0 axis offsets
M568 P0 R160 S200 A0                                     ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"hotTOO" D1 H2 F2                            	 ; define tool 1
G10 P1 X12 Y0 Z0                                         ; set tool 1 axis offsets
M568 P1 R160 S200 A0                                  	 ; set initial tool 1 active and standby temperatures to 0C

; Miscellaneous
M501                                                     ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"       ; set voltage thresholds and actions to run on power loss
M140 S65 R40