Posts made by Preischl3D

@petrkroupa I bought a new sensor. But it had the same problems. Then I changed the connection to a different pin assignment and laid the cable so that it did not cross any other cables.
In the meantime, the error hardly ever occurs. Not at all for the last 2 weeks. I'm keeping my fingers crossed that it stays that way

@t3p3tony It happens again:

4.12.2021, 22:47:36 m591 d0
Duet3D rotating magnet filament monitor v3 on pin io3.in, enabled, sensitivity 25.00mm/rev, allow 50% to 150%, check every 30.0mm, version 3, mag 129 agc 93, measured sensitivity 25.67mm/rev, min 96% max 103% over 3645.8mm
4.12.2021, 22:47:19 m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TN-6JTD4-3SJ6S-KV82V
Used output buffers: 1 of 40 (13 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 62464 of which 16 recycled
Never used RAM 137952, free system stack 134 words
Tasks: SBC(ready,14.8%,328) HEAT(notifyWait,0.1%,325) Move(notifyWait,0.1%,250) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,362) CanClock(delaying,0.0%,333) TMC(notifyWait,24.0%,59) MAIN(running,61.0%,922) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 04:43:33 ago, cause: software
Last software reset at 2021-12-04 17:03, reason: User, none spinning, available RAM 137952, slot 0
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 176
MCU temperature: min 48.7, current 49.0, max 51.9
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/38/38, gc cycles 0
Driver 0: position 0, standstill, reads 17580, writes 23 timeouts 0, SG min/max 0/1023
Driver 1: position 0, standstill, reads 17580, writes 23 timeouts 0, SG min/max 0/1023
Driver 2: position 320125, standstill, reads 17580, writes 23 timeouts 0, SG min/max 0/1023
Driver 3: position 0, standstill, reads 17580, writes 23 timeouts 0, SG min/max 0/1023
Driver 4: position 0, standstill, reads 17580, writes 23 timeouts 0, SG min/max 0/1023
Driver 5: position 0, standstill, reads 17585, writes 19 timeouts 0, SG min/max 0/463
Date/time: 2021-12-04 21:47:22
Slowest loop: 246.78ms; fastest: 0.02ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 357066ms, bed compensation in use: mesh, comp offset 0.115
=== MainDDARing ===
Scheduled moves 14691, completed moves 14691, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause* is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0: pos 59.77, errs: frame 6 parity 0 ovrun 30 pol 0 ovdue 0
=== CAN ===
Messages queued 153166, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49), ts 85070/0/0
Tx timeouts 0,64,85069,0,0,68030 last cancelled message type 30 dest 127

=== SBC interface ===
State: 4, failed transfers: 0, checksum errors: 0
Last transfer: 2ms ago
RX/TX seq numbers: 29787/29787
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c83c
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 36.42, max wait times: 15.0ms/0.0ms
Codes per second: 1.53
Maximum length of RX/TX data transfers: 3152/1632

Totally random!

Of course, the test print has now been successful. (11hours) I'll write in here again when i have the error again xD

Thanks for the Answer!
The problem occurs totally randomly. I had it on 5 different models at different layerhights and at the same gcode between 0 and 5 times. Because I need the printer for orders, I have now printed them with the sensor deactivated and everything worked fine. Now I have reactivated the sensor and am trying to reproduce the error. So far it is still running well. Nevertheless, here are the excerpts for the start of printing. I will add the evaluation during printing later.

M122:

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TN-6JTD4-3SJ6S-KV82V
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 62248 of which 16 recycled
Never used RAM 141024, free system stack 204 words
Tasks: SBC(ready,6.2%,336) HEAT(notifyWait,0.0%,331) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,333) TMC(notifyWait,7.2%,93) MAIN(running,86.4%,922) IDLE(ready,0.2%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:51 ago, cause: software
Last software reset at 2021-11-23 09:03, reason: User, none spinning, available RAM 138212, slot 2
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0440f000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 131
MCU temperature: min 45.7, current 46.0, max 46.1
Supply voltage: min 24.0, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 25197, writes 15 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 25197, writes 15 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 25197, writes 15 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 25197, writes 15 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 25197, writes 15 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 25198, writes 15 timeouts 0, SG min/max 0/0
Date/time: 2021-11-23 09:04:07
Slowest loop: 0.44ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0: pos 254.88, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0
=== CAN ===
Messages queued 440, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49), ts 258/0/0
Tx timeouts 0,0,257,0,0,181 last cancelled message type 4514 dest 127

=== SBC interface ===
State: 4, failed transfers: 0, checksum errors: 0
Last transfer: 1ms ago
RX/TX seq numbers: 1746/1746
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c83c
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 35.24, max wait times: 8.6ms/0.0ms
Codes per second: 1.25
Maximum length of RX/TX data transfers: 3064/780

---

M591:

m591 d0
Duet3D rotating magnet filament monitor v3 on pin io3.in, enabled, sensitivity 26.25mm/rev, allow 50% to 150%, check every 30.0mm, version 3, mag 129 agc 46, no calibration data

---

Prusa Slicer StartGCODE:

G90 ; use absolute coordinates
M83 ; extruder relative mode
M190 S[first_layer_bed_temperature] ; wait for bed temp
G4 S300
G32 ; true bed leveling
G29 ; mesh bed leveling
G28 ; Homing
G1 X0 Y0 F10000 ; go outside print area
M109 S[first_layer_temperature] ; wait for extruder temp
M221 S{if layer_height<0.075}100{else}95{endif}

Hello,

I have a strange problem. My filament sensor works perfectly. It is super calibrated and also reports problems when they occur.
But sometimes it reports 'sensorError' and pauses printing. This is very annoying as there is no error and I don't know what it is.

Here is the log:

2021-11-21 19:29:50 Event logging started
2021-11-21 21:53:47 Extruder 0 reported 'sensorError'.
2021-11-21 21:53:52 Printing paused at X236.4 Y213.2 Z41.6

I checked the status LED of the sensor. It flashes normally (alternating green/red). When filament passes, it also responds normally with a fast green flashing.
The cable is routed alone so that it does not receive any interference. When reading out the M591 command, nothing unusual is displayed. They are all comprehensible values. An evaluation with M122 results in 6 frame errors for the sensor.
How can I find out what the error could be? Unfortunately, I have no indicator for such a short error message.

All parts are brand new, original and the Duet 6HC is on version 3.3.

Thanks