I have bigbox printer with idex gonfiguration. I dont had any problem before this.
Everything started yesterday. I had printing on going and suddenly u-axis titan extruder start skipping steps and i have to stop printing.
Extruder bearing was jammed and i change it to new one. It work again.. i think.
Today i start to print same print again. everything goes well until i noticed u-axis was skipped steps and print was fail.
I start to printing again and after first layer Duet board reseting itself and print stopped. I try again and this time reseting happened on layer 6. Now i put voltage meter to measuring if power is going down and i start print again. Power is ok voltage is steady 24.25V but still duet reseting. It happend every print between 1 and 6 layers. I also try to print with X-axis and same thing happen. Any good idea what causing this?
M122
[CODE]
=== Diagnostics ===
Used output buffers: 3 of 32 (16 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.20 running on Duet WiFi 1.0 + DueX5
Board ID: 08DAM-999TL-MQ4S8-6JKFA-3SD6L-9P8RZ
Static ram used: 15448
Dynamic ram used: 99240
Recycled dynamic ram: 4096
Stack ram used: 1392 current, 6096 maximum
Never used ram: 6192
Last reset 00:52:41 ago, cause: reset button or watchdog
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 7896 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.2ms
MCU temperature: min 42.4, current 42.5, max 44.5
Supply voltage: min 24.3, current 24.5, max 24.8, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Expansion motor(s) stall indication: yes
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest main loop (seconds): 0.063058; fastest: 0.000046
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.20
WiFi MAC address 5c:cf:7f:2b:e7:3e
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 16656
WiFi IP address 192.168.1.89
WiFi signal strength -54dBm, reconnections 0, sleep mode modem
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
[/CODE]
Logs not give anything
power up + 00:00:00 Event logging started
power up + 00:00:01 WiFi module started
power up + 00:00:05 Wifi module is connected to access point ReiDiDin, IP address 192.168.1.89
power up + 00:00:11 HTTP client 192.168.1.57 login succeeded
2018-04-18 20:50:38 Date and time set at power up + 00:00:11
2018-04-18 20:51:43 Started printing file 0:/gcodes/Sodastream_keg v7.gcode
power up + 00:00:00 Event logging started
power up + 00:00:00 WiFi module started
power up + 00:00:05 Wifi module is connected to access point ReiDiDin, IP address 192.168.1.89