Sorted it and dancing around the workshop .
Looked at all the frequency settings on VFD and noticed that PD011 was set to 200.00. Set it to factory 0 and it all works.
Thanks so much for all your help. This forum is invaluable.

@chrishamm Yep that sorted it. Thanks for your help.

@chrishamm Yep that sorted it. Thanks for your help.

Hi,
I have a workbee 1010 with Duet 3 and RRF 3.3.
I have spindle control via the duet which starts and stops the spindle at beginning and end of job.
However if I PAUSE a job part way through, the spindle rises but does not stop, before waiting 10 seconds and then travelling to rear right of machine. I can however send M5 directly to switch it off from DWC so I know M5 works.
Any ideas?
TIA

PAUSE.g
; pause.g
; called when a print from SD card is paused
G90
G53 G1 Z{move.axes[2].max} F1500 ; move the Z-Axis to the maximum position
M5 ; turn off spindle
G4 S10 : wait for spindle to stop
G53 G1 X{move.axes[0].max} F2500 ; move the X-Axis to the maximum position
G53 G1 Y{move.axes[1].max} F2500 ; move the Y-Axis to the maximum position

RESUME.g
; resume.g
; called before a print from SD card is resumed

M3 R1 ;restore
G4 S10 ;wait for spindle to reach full speed
G1 H1 Z1500 F1500 ; raise the Z to the highest position
G1 R1 X0 Y0 ; go to directly above position of the last print move
G1 R1 X0 Y0 Z0 ; go back to the last print move

Sorted it and dancing around the workshop .
Looked at all the frequency settings on VFD and noticed that PD011 was set to 200.00. Set it to factory 0 and it all works.
Thanks so much for all your help. This forum is invaluable.

@jay_s_uk Still no joy. Set it to 6000 and M5 still wont make it stop. Tearing my hair out now as I cant get my head arround whats going on. Could it be a VFD setting?

@jay_s_uk Hi 1.5kw aircooled spindle

@jay_s_uk Minimum RPM on specs is 0 but have tried it at 600 but still the same.
If I adjust the 12000rpm it knocks the 24000rpm which is spot on, would it be an innacuracy with the 0-10v converter?

@jay_s_uk Minimum rpm is currently set to 0, should it be something else then?

Also just noticed that as I have to press STOP on the VFD to stop spindle I then can't restart using Web Control or Gcode.
Also when set at 12000rpm on web control it shows just over 13500rpm on VFD. Is this just a case of fine tuning the 0-10v converter?

@jay_s_uk So So close now. I now have spindle on and off and speed control via web control and gcode .
The only thing still not working is M5- Stop. When M5 is activated the spindle drops to about 500rpm, although VFD still shows 12000rpm, and stays there.
Is there a minimum RPM setting somewhere?
Thanks for your support so far you have been awesome!

@jay_s_uk Have tried Gnd on pin out 6 to FOR
Changed M950 R0 C"out9+out6" L0:24000 Q1000
Also tried to put directly into config.g but still no spindle start or stop.
Checking again with RUN button on VFD reactivated and I have speed control and sort of a stop control M5 but it just reduces to 500rpm not a complete stop.
Any further ideas?