Posts made by PCNoobNeedsMajorHelp

@dc42 I found this SSR amongst my things and was wondering if I could use this? If it's better for the bed to use the 25DA I'll get that instead.

@dc42

Thank you so much @RogerPodacter and @dc42!!!

@Phaedrux

Hey...It's been a while. You originally helped me in this post: HELP! Duet 2 WiFi Configuration and DWC Upload???. After a very busy year I'm finally ready to install my Keenovo Heated bed upgrade. I think I got the wrong heated bed though. I have a 24v 350w Keenovo, and I have a 24v 350w power supply as well as an SSR. I was reading up on the stock heated bed for the Ender 5 and it's a 24v 350w bed as well (facepalm). I'm realizing now that I should have gotten a 110v 500w heated pad for higher temperatures for my bed plate where I would be pulling power from the Mains on my PSU rather than the 24 volts it supplies to the rest of the Duet. Am I correct in my thinking?

Thanks in advance for any guidance

@droftarts

Do you want me to post another one for this question or just for next time?

@Phaedrux
(I decided to reply to this thread so you'd remember me)

Hey...It's been a while. After a very busy year I'm finally ready to install my Keenovo Heated bed upgrade. I think I got the wrong heated bed though. I have a 24v 350w Keenovo, and I have a 24v 350w power supply as well as an SSR. I was reading up on the stock heated bed for the Ender 5 and it's a 24v 350w bed as well (facepalm). I'm realizing now that I should have gotten a 110v 500w heated pad for higher temperatures for my bed plate where I would be pulling power from the Mains on my PSU rather than the 24 volts it supplies to the rest of the Duet. Am I correct in my thinking?

Thanks in advance for any guidance

I haven't used my printer in a while. The last time I used it everything worked great, so I'm not sure why I'm getting a fault. All my connections look good. Not sure where to go from here or how to fix it. Thanks in advance!

@phaedrux

So I'm testing some new filaments, and on the technical data sheet it says for the print bed to be at 140°c. I'm almost positive mine maxes out at 110, which means i need to upgrade. Do you have any suggestions.

I was thinking these (one generic, one brand)

https://www.amazon.com/gp/product/B07GJGCBNP/ref=ox_sc_act_title_1?smid=AJUKUXZVPYM6H&psc=1

https://keenovo.store/products/keenovo-silicone-heater-235mm-x-235mm-for-ender-3-3d-printer-build-plate-heatbed-heating-upgrade

What's your take on it?

Thanks,

-Carson

@phaedrux

Thanks

@phaedrux

ok I'll look into it

@phaedrux

How do I do that?

@phaedrux

Just out of curiosity I tried out a few IP Addresses, and somehow the IP was changed. I don't know how, but its working under a different IP now. But it is working.

yeah config.g and www are both on the card

@phaedrux

OK, I got it working and this was the output

@phaedrux

So I'm trying to use YAT but I'm not getting anywhere. my COM Port isn't being detected. I'm lost when it comes to terminals

@phaedrux

Ok so i did that and got this

so if i connect via USB what program should I open? YAT, Arduino, Visual Studio Code?

@phaedrux

Just to be sure I copied all of my files to a new Micro SD and I'm getting the same result/issue.

404 Not Found

@phaedrux

When I inserted the micro SD into my PC it said something was wrong with it but I just ignored it because PC's are stupid that way, and there usually aren't any problems. The SD card functioned properly though (I was able to access all the files)

@phaedrux

Through the PanelDue I sent the M122 and I got this message

and the blue LED is on

@phaedrux

So I'm getting a 404 Error when I try and access the DWC address page.

Sometimes the address works and sometimes it doesn't. It's like hit or miss. Every time I do an update on my PC it seems to happen more, but all of my settings are set to allow the address to load. I've turned off my VPN just in case and still nothing. Solutions?

Sometimes the address works and sometimes it doesn't. It's like hit or miss. Every time I do an update on my PC it seems to happen more, but all of my settings are set to allow the address to load. I've turned off my VPN just in case and still nothing. Solutions?

@phaedrux

Just found these. I actually might get one. For both android and ios.

https://www.flir.com/products/flir-one-gen-3/