Thank you @dc42
@T3P3Tony yes thankfully I have my machine up and running. It is a Tronxy X5ST 500x500x600mm with a titan aero, bl touch and of course a duet wifi. Lot of hours being that I am new to this but happy with the result.

Thank you @dc42
@T3P3Tony yes thankfully I have my machine up and running. It is a Tronxy X5ST 500x500x600mm with a titan aero, bl touch and of course a duet wifi. Lot of hours being that I am new to this but happy with the result.

Thank you @bearer I am in Buffalo, NY.

Neither of the boards have any physical damage as far as I can tell.

Board 1: I moved my printer to a more stable table and I believe the panel due connection was loose when I reconnected it and then the board got really hot not even plugged in to power ( I read this means I have a problem with my processor?)

My panel due is also damaged, it lights up a black screen but does not show anything.

Board 2: Due to loose wires connectivity to the firmware became flakey and the fan and Z probe stopped working

Best,

Paul

Hello All,

I have two duet wifi boards and a panel due that need repair. Can anyone suggest where I can send them.

Best,

Paul

Thank you @chas2706 @DennisHall @Veti I apologize for the delay I have been out of town. I just ordered new tubes since I can't even unclog the the one that I have. I am told this is called heat creep and assume this is due to my temperature and fan settings being wrong. I will try to adjust the config and if that doesn't work possibly get a direct extruder. Any hot end and fan config suggestions are appreciated. Thanks!

Thanks again @chas2706 and @DennisHall
I got that all configured and got some printing going but the filament keeps getting jammed. The extruder spins but filament gets stuck after a few layers. Other than cleaning out the nozzle, how can I prevent this? Lower temperature or turn fans up? Best, Paul

Thank you @DennisHall and @chas2706 I got the Z prove to light up and seems to be connected properly! Unfortunately my dynamic test is failed. When I put a flat surface under the probe it lit up but the z axis did not stop moving. I used the Z probe config codes you sent. Any ideas what could be going wrong here? Thanks again.

Thank you both! I am new to this and appreciate both of your responses. I took some time to go through them both and learned I do not have a z end stop, but a Z probe. I have the TronXY XY-08N and I read about it where it was mentioned in another post on this forum. I had it plugged into the Z end stop input (sounds like it can't draw enough power there. Can I change the connector and connect to the Z probe input next to the Panel Duel? The Z probe only has 3 wires (black, brown and blue) while the Z probe input has 4 slots. I see where ground goes but unsure where to put the brown and blue wires and one would be left open?

I saw the post about using the always on fan input to power the sensor. What is a fan voltage jumper and where do I get one of those?

At this stage I need to get this sensor connected properly. But looking forward to configuration, should I select Unmodulated or smart IR probe, Simple modulated Ir probe, Smart effecto or Piezo or BL touch? Then what should my trigger height and value be?

Thanks again. Looking forward to getting this thing fired up.

Hello All and Happy 420!

I bought and assembled at Tronxy X5ST 500. (500x500x600) I got the better part of 40 hours in this build and am stuck. I upgraded my board to a Duet Wifi 2.

I was able to successfully connected to the board and I can control the movement of my x and Y axis. The Z axis seems to move up okay and down intermittently. It does not home properly. It just moves up a little no matter where it begins. I can’t home all correctly. I am unable to print. When I send a Gcode print file the x and y move how they should but the z is not in place and no filament is coming out. I believe this is a configuration issue. I followed the configuration instructions for a core xy printer on the duet site. Any advice would be greatly appreciated. See my config files below.

Also does anyone have a Tronxy X5ST?

Home all file:

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 20 2019 00:53:57 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X-505 Y-505 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 S1 X-505 ; home X axis
G1 S1 Y-505 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 S1 X-505 F360 ; move slowly to X axis endstop once more (second pass)
G1 S1 Y-505 ; then move slowly to Y axis endstop
G1 S1 Z-605 F1800 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

Home X:
; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 20 2019 00:53:58 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X-505 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000 ; go back a few mm
G1 S1 X-505 F360 ; move slowly to X axis endstop once more (second pass)
G1 Z-5 F6000 S2 ; lower Z again
G90 ; absolute positioning

Home Y file:

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 20 2019 00:53:58 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 Y-505 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000 ; go back a few mm
G1 S1 Y-505 F360 ; move slowly to Y axis endstop once more (second pass)
G1 Z-5 F6000 S2 ; lower Z again
G90 ; absolute positioning

Home z file:

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 20 2019 00:53:58 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 Z-605 F1800 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

Main config file:

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 20 2019 00:53:57 GMT-0400 (Eastern Daylight Time)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

M667 S1 ; Select CoreXY mode

; Network
M550 P"Revo 1" ; Set machine name
M552 S1 ; Enable network
M587 S"Spaghetti" P"donttellne1" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E98.00 ; Set steps per mm
M566 X600.00 Y600.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z180.00 E1500.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000.00 ; Set accelerations (mm/s^2)
M906 X950.00 Y950.00 Z950.00 E950.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X500 Y500 Z600 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 Z1 S0 ; Set active low and disabled endstops

; Z-Probe
M558 P2 H5 F120 T6000 ; Set Z probe type to modulated and the dive height + speeds
G31 P600 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:500 Y15:500 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured