@Phaedrux
Glad to hear on the probe status speed. I was going by one of the tutorials and it said it should show 1000 when triggered. I did try the G30 and it deploys the probe and moves z. Unfortunately it crashes (or I Estop it). The white signal wire is good all the way to the board.
heres my config:
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Jan 25 2020 19:53:13 GMT-0500 (Eastern Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Parabolic X" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X420000.00 Y420000.00 Z1500.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z250.00 E250.00 ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1800 E1500 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X395 Y410 Z400 S0 ; set axis maxima
; Endstops
M574 X1 Y1 S0 ; set active low and disabled endstops
M574 Z1 S2 ; set endstops controlled by probe
; Z-Probe
M307 H3 A-1 C-1 D-1 ; set Z probe type to switch and the dive height + speeds
M558 P9 H5 F1000 T20000
G31 X0 Y50 Z1.5 P25 ; set Z probe trigger value, offset and trigger height
M557 X5:385 Y0:360 S90 ; define mesh grid
; Heaters
M140 H0 ; enable heated bed
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.06e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 A492.3 C163.8 D3.8 V24.3 B0 ;PID settings
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 T50 H1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 S"HotEnd" D0 H1 F0 ; define tool 0
;G10 P0 X0 Y-80 Z2 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
;G31 X0 Y0 Z0 P25
; Custom settings are not defined