Im having this issue when i start any print.
i have already ran the auto calibration and updated the M665 & M666 per this link https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareDeltaPrinter?fbclid=IwAR0FyapfQXN1LNuSmc9Pz63V_2w1EMoH-yCCYjtpPaU_yiQyteWJjl1-Y3M
here is a video showing the issue
https://www.facebook.com/michael.mcnair.7792/videos/2141336582579449/
can someone help me with configuring a anycubic kossel plus with the duet board. i have everything hooked up and is running but im having the issue with bed leveling and im unsure what my parameters should be for this printer. (Rod length, delta radius, printable radius, maximum carriage travel, homed height, minimum z.) what should the microstepping be?
im using the Z-probe that came with the printer. what should the trigger height be and trigger value.
what should the Bed probing for delta calibration be set to. (Compensation)
im using the RepRapFirmware confiuration tool. but a lot it is asking im not sure about.
@doctrucker yes I pulled the values from another person.
I ran the bed leveling and mesh leveling with the probe 2 from anycubic. I started a calibration cube print and the printer changes height when moving from one corner of the print to the other.
okay i got it i needed to add a jumper to both the v fan and int 5v. im so afraid of damaging the board i have already damaged two gorilla boards on my anycubic kossel.
i moved the jumper from the int 5v en to the v fan jumper fan select. now only the fan comes on and none of the green lights on the board come on
is there only post to be one jumper in ?
the part cooling fan came on that is plugged into the always fan port, but none of the green lights come on ?
so the two pins on the right ?
it is currently on the Jumper: int 5V EN
which position should the jumper be in ?
here is what i put as my fans
; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, gcode control for part cooling fan
M106 P1 S0.5 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3S4-6J1D8-3SD6J-1VR7F
Used output buffers: 3 of 20 (9 max)
=== RTOS ===
Static ram: 25524
Dynamic ram: 98620 of which 0 recycled
Exception stack ram used: 280
Never used ram: 6648
Tasks: NETWORK(ready,656) HEAT(blocked,1232) MAIN(running,3788) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:00:19 ago, cause: power up
Last software reset at 2019-02-12 20:13, reason: User, spinning module GCodes, available RAM 6648 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 18.3, current 21.5, max 21.8
Supply voltage: min 12.7, current 12.7, max 12.8, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2019-02-13 17:55:58
Cache data hit count 63519798
Slowest loop: 6.96ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 22.72ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
all my fans were working fine before i upgraded to the duet board.
yes and neither fan is turning on when i have them in the always on connector
im new to the duet board ? please explain
I still dont get any movement out of the fans.
