@droftarts Thank you, setting M906 fixed the issue. It is working now. I wonder how it was working the first time without this, maybe I accidentally checked out an older version of the code
Thank you again for the help

@droftarts I am using an M302 P1 command, the buttons are not greyed out. I can press them and Duet accepts this, the DWC dashboard even shows the extruders moving, but the hardware does not move at all. I know it is not a hardware problem because I tested defining those extruder motors as axises and that allows them to move fine. I am testing with G1 Ennn:nnn already.

Not sure why, but it is not working anymore. I cannot control the extruders at all. Didn't change the config as far as I know of.
Config.g:

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"printername" ; set hostname

; Network
M552 Pxxx.xxx.x.xxS1 ; configure Ethernet adapter (IP hidden, there is a real address in it)
M553 P255.255.255.0 ; set netmask
M554 Pxxx.xxx.x.xx ; set gateway
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0 S0 D2                      ; driver 0.0 goes forwards (Z axis)
M569 P1 S1 D2                      ; driver 0.1 goes forwards (A axis)
M569 P2 S1 D2                      ; driver 0.2 goes forwards (X axis)
M569 P3 S1 D2                      ; driver 0.3 goes forwards (extruder 0)
M569 P4 S1 D2                      ; driver 0.4 goes forwards (extruder 1)
M569 P5 S1 D2                      ; driver 0.5 goes forwards (Y axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes (Note: Y axis not functional)
M584 X2 Y4 Z0 A1        ; set axis mapping

M350 X16 Y16 Z16 A16 I1 ;E16:16 I1          ; configure microstepping with interpolation
M906 X1500 Y0 Z1500 A1500 ;E1000:1000 ; set motor driver currents
M92 X400 Y800 Z400 A800 ;E492.15:420             ; configure steps per mm
M208 X0:200 Y0:200 Z0:200 A-360:720 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 A900 ;E1200:1200         ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 A20000 ;E3600:3600     ; set maximum speeds (mm/min)
M201 X500 Y500 Z200 A1000 ;E250:250         ; set accelerations (mm/s^2)


; Extruders
M584 E3:5   ; set extruder mapping
;M350 E16:16 I1  ; configure microstepping with interpolation
; NOTE: See Smart Drivers section for motor currents
M92 E1000:1000    ; configure steps per mm 492.15:420 
M566 E1200:1200   ; set maximum instantaneous speed changes (mm/min)
M203 E3600:3600 ; set maximum speeds (mm/min)
M201 E250:250   ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Probes
M558 K0 P1 C"io3.in" H5 F120 T6000 ; configure analog probe via slot #0
G31 P500 X0 Y0 Z0.7                ; set Z probe trigger value, offset and trigger height

; Endstops
;M574 X0 ; configure X axis endstop
;M574 Y0 ; configure Y axis endstop
;M574 Z0 ; configure Z axis endstop
;M574 A0 ; configure A axis endstop

; Sensors
M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B4725 C7.06e-8          ; configure sensor #0
M308 S1 P"temp1" Y"PT1000" A"Nozzle Thermistor 1" ; configure sensor #1
M308 S2 P"temp2" Y"PT1000" A"Nozzle Thermistor 2" ; configure sensor #2

;M308 S1 P"temp1" Y"thermistor" A"Nozzle Thermistor 1" T100000 B4725 C7.06e-8 ; configure sensor #1
;M308 S2 P"temp2" Y"thermistor" A"Nozzle Thermistor 2" T100000 B4725 C7.06e-8 ; configure sensor #2

; Heaters
M950 H0 C"out0" T0                ; create heater #0
M143 H0 P0 T0 C0 S140 A0          ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"out1" T1                ; create heater #1
M143 H1 P0 T1 C0 S285 A0          ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1
M950 H2 C"out2" T1                ; create heater #2
M143 H2 P0 T1 C0 S285 A0          ; configure heater monitor #0 for heater #2
M307 H2 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #2

; Heated beds
M140 P0 H0                        ; configure heated bed #0

; Fans
M950 F0 C"out6"       ; create fan #0
M106 P0 S0 L0 X1 B0.1 ; configure fan #0

; Tools
;T0__________________________________________________________
M563 P0 S"E0 Filament" D0 H1 F0                 ; Define tool 0
G10 P0 X0 Y0 Z0                                ; Set tool 0 axis offsets
G10 P0 R0 S0                                 ; Set initial tool 0 active and standby temperatures to 0C

;T1__________________________________________________________
M563 P1 S"E1 CF" D1 H2 F1               ; Define tool 1
G10 P1 X0 Y0 Z0                               ; Set tool 1 axis offsets
G10 P1 R0 S0                                 ; Set initial tool 1 active and standby temperatures to 0C

;T2__________________________________________________________
M563 P2 S"E2 Both" D0:1 H1:2 F0:1              ; Define tool 2
M567 P2 E1.00:1.00                             ; 100% Mix Ratio for both tools
G10 P2 X0 Y0 Z0                                ; Set tool 2 axis offsets
G10 P2 R0 S0                                 ; Set initial tool 2 active and standby temperatures to 0C


;M563 P0 D0 H1 F0 ; create tool #0
M568 P2 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
T2 ; select first tool

M98"config.g" reports no errors, the only output is 'HTTP is enabled on port 80'.
M112 reports the firmware is 3.5.3, which still is the latest release candidate. Switching the motors into the drivers for one of the motion axis reveals that the hardware is working fine. The interface seems to think it has two functional extruders, I see all the controls, but hitting extrude or using a command (ie G1 E100 or G1 E200:100) does nothing at all. I see no motor movement. Does anyone know why this might be happening?

@droftarts @Phaedrux thank you both so much. It is working properly now.

@Phaedrux I have updated the firmware to the latest version (3.5.3). For M98, the DWC interface disconnects and the printer does not reconnect after a while. What should I do next?
Update: Seems to be working after a restart. Output is:

M98 P"config.g"
HTTP is enabled on port 80
Warning: Heater 0 predicted maximum temperature at full power is 321°C
Error: bad drive number
Error: in file macro line 93: M567: Invalid tool number
Error: in file macro line 94: G10: Invalid tool number
Error: in file macro line 95: G10: Invalid tool number
Error: in file macro line 100: M568: Invalid tool number

All of these refer to an instance where I have specified the extruders in some form of 3:4, but per my understanding this should be a valid syntax? I used this syntax for axises and it worked without issue, and I have seen others do this.

@Phaedrux said in Mixing hotend only driving first extruder:

M122

=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.4+1 (2022-11-15 17:36:33) running on Duet 3 MB6HC v1.02 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3T0-6J1DL-3SD6L-KS0M9
Used output buffers: 1 of 40 (15 max)
=== RTOS ===
Static ram: 152740
Dynamic ram: 98148 of which 144 recycled
Never used RAM 99640, free system stack 218 words
Tasks: NETWORK(ready,29.8%,238) ETHERNET(notifyWait,0.1%,453) HEAT(notifyWait,0.0%,328) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,336) CanClock(delaying,0.0%,343) TMC(notifyWait,6.8%,91) MAIN(running,62.6%,925) IDLE(ready,0.7%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:14 ago, cause: software
Last software reset at 2024-10-21 12:32, reason: User, GCodes spinning, available RAM 99640, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 125
MCU temperature: min 44.5, current 44.7, max 45.1
Supply voltage: min 36.4, current 36.4, max 36.5, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 8, reads 17579, writes 15 timeouts 0
Driver 1: standstill, SG min 0, mspos 8, reads 17579, writes 15 timeouts 0
Driver 2: standstill, SG min 0, mspos 8, reads 17579, writes 15 timeouts 0
Driver 3: standstill, SG min 0, mspos 8, reads 17579, writes 15 timeouts 0
Driver 4: standstill, SG min 0, mspos 8, reads 17579, writes 15 timeouts 0
Driver 5: standstill, SG min 0, mspos 8, reads 17580, writes 15 timeouts 0
Date/time: 2024-10-21 12:33:00
Slowest loop: 1.09ms; fastest: 0.06ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 133, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 75/0/0
Tx timeouts 0,0,74,0,0,57 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 2.55ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
State: active
Error counts: 0 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
= WiFi =
Network state is disabled
WiFi module is disabled
Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
Socket states: 0 0 0 0 0 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0

config.g:

; Configuration file for RepRapFirmware on Duet 3 Main Board 6HC
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.4 on Fri Oct 11 2024 04:13:11 GMT+0000 (Greenwich Mean Time)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"name" ; set hostname

; Network
M552 P192.168.0.66 S1 ; configure Ethernet adapter
M553 P255.255.255.0 ; set netmask
M554 P192.168.0.67 ; set gateway
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0.0 S0 D2                      ; driver 0.0 goes forwards (Z axis)
M569 P0.1 S1 D2                      ; driver 0.1 goes forwards (A axis)
M569 P0.2 S1 D2                      ; driver 0.2 goes forwards (X axis)
M569 P0.3 S1 D2                      ; driver 0.3 goes forwards (extruder 0)
M569 P0.4 S1 D2                      ; driver 0.4 goes forwards (extruder 1)
M569 P0.5 S1 D2                      ; driver 0.5 goes forwards (Y axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes (Note: Y axis not functional)
M584 X0.2 Y0.5 Z0.0 A0.1 E0.3:0.4        ; set axis mapping

M350 X16 Y16 Z16 A16 I1 E16:16 I1          ; configure microstepping with interpolation
M906 X1500 Y0 Z1500 A1500 E1000 ; set motor driver currents
M92 X400 Y800 Z400 A800 E492.15:420             ; configure steps per mm
M208 X0:200 Y0:200 Z0:200 A-360:720 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 A900 E1200:1200         ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 A20000 E3600:3600     ; set maximum speeds (mm/min)
M201 X500 Y500 Z200 A1000 E250:250         ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Probes
M558 K0 P1 C"io3.in" H5 F120 T6000 ; configure analog probe via slot #0
G31 P500 X0 Y0 Z0.7                ; set Z probe trigger value, offset and trigger height

; Endstops
;M574 X0 ; configure X axis endstop
;M574 Y0 ; configure Y axis endstop
;M574 Z0 ; configure Z axis endstop
;M574 A0 ; configure A axis endstop

; Sensors
M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B4725 C7.06e-8          ; configure sensor #0
M308 S1 P"temp1" Y"PT1000" A"Nozzle Thermistor 1" ; configure sensor #1
M308 S2 P"temp2" Y"PT1000" A"Nozzle Thermistor 2" ; configure sensor #2

;M308 S1 P"temp1" Y"thermistor" A"Nozzle Thermistor 1" T100000 B4725 C7.06e-8 ; configure sensor #1
;M308 S2 P"temp2" Y"thermistor" A"Nozzle Thermistor 2" T100000 B4725 C7.06e-8 ; configure sensor #2

; Heaters
M950 H0 C"out0" T0                ; create heater #0
M143 H0 P0 T0 C0 S140 A0          ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"out1" T1                ; create heater #1
M143 H1 P0 T1 C0 S285 A0          ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1
M950 H2 C"out2" T1                ; create heater #2
M143 H2 P0 T1 C0 S285 A0          ; configure heater monitor #0 for heater #2
M307 H2 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #2

; Heated beds
M140 P0 H0                        ; configure heated bed #0

; Fans
M950 F0 C"out6"       ; create fan #0
M106 P0 S0 L0 X1 B0.1 ; configure fan #0

; Tools
;T0__________________________________________________________
;M563 P0 S"E0 Filament 1" D0.3 H1 F0                 ; Define tool 0
;G10 P0 X0 Y0 Z0                                ; Set tool 0 axis offsets
;G10 P0 R0 S0                                 ; Set initial tool 0 active and standby temperatures to 0C

;T1__________________________________________________________
;M563 P1 S"E1 Filament 2" D0.4 H2 F1               ; Define tool 1
;G10 P1 X0 Y0 Z0                               ; Set tool 1 axis offsets
;G10 P1 R0 S0                                 ; Set initial tool 1 active and standby temperatures to 0C

;T2__________________________________________________________
M563 P2 S"E2 Both" D0.3:0.4 H1              ; Define tool 2
M567 P2 E1.00:1.00                             ; 100% Mix Ratio for both tools
G10 P2 X0 Y0 Z0                                ; Set tool 2 axis offsets
G10 P2 R0 S0                                 ; Set initial tool 2 active and standby temperatures to 0C

;M563 P0 D0 H1 F0 ; create tool #0
;M563 P2 D0.3:0.4 H1 F0 ;create tool #2
M568 P2 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
T2 ; select first tool
M302 P1 ;allow cold extrusion, DISABLE for printing

M302 is used just for my testing purposes, I will be disabling it for real printing usage. M98"config.g" crashes my machine, I am not sure why.

Hi, I am currently working on a printer with a mixing hotend (two extruders, one nozzle). To make this printer work, I need both extruders running at once. I have followed the documentation Duet provides as well as some other resources I have found, but one error remains consistent. When I define the extruders as "E0.3:0.4" with 0.3 and 0.4 being my respective extruders, only the first one is moved (If 0.3 is first, 0.3 moves, if 0.4 is first, 0.4 moves). They are configured to the same tool. I have tried linking these two motors to the A-axis and driving them as such synchronously, this works without issue. I have also tried re-numbering them to 0 and 1 in case the decimal was the issue, but this is not either. The mixing ratio is set to 1:1. When I try to call "G1 E10:10", I get an error saying that the maximum length of array expected was 1, making me believe there is some error. Does anyone have any knowledge on this?

Hello, new to this forum. I have a DUET 3 Main board 6HC which I use to control a printer. I would like to communicate with a raspberry pi machine through UART. This pi is mounted to a different hardware machine, so I can't mount it as an SBC on the duet itself. I see that the 5-pin I/O connectors on the MB6HC have UART compatability, so I thought I could use those. I have a simple G-code file for testing this, but I ran into trouble defining the port (IO_1) for use with the M575/M118 commands. The documentation only seems to include the port numbers for the CAN bus and the USB-C, which is in use as a power supply for this Duet. Per my understanding, setting it up as a series of GPIO pins through M950 will not help here.
How can I define IO_1 as a port for UART communication?