Posts made by Monster Delta

hi i have a duet wifi with a knackered atmel chip if anyone could replace it, i have the replacement part and im located in the uk so europe would be best. drop me a message. thankyou

replacement received and all is working as it should now

Its not the wiring as it worka fine with the laser version. Im just about out of ideas i think I'll send it back and see if the folks at duet can figure it out

@dc42 did you get chance to look into this

@poohzaza what do you mean by logic of filament sensing?

Any one.

ok so im getting somewhere now. i can start a print but but every few minutes i get an error sensor not working sometimes there is a red flashing led no code just constant slow flash, other times there is nothing at all but then it willflash green 4 times and i can resume the print but a few minutes later it happens again. and then sometimes the duet will restart all by itself heres an m122 reort from the last instance

22/09/2019, 18:01:21: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04RC1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3SN-6J9FL-3S46J-1SYMD
Used output buffers: 3 of 24 (21 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93640 of which 284 recycled
Exception stack ram used: 320
Never used ram: 11148
Tasks: NETWORK(ready,652) HEAT(blocked,1204) MAIN(running,3756) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:00:16 ago, cause: software
Last software reset at 2019-09-22 17:56, reason: Unknown, spinning module Platform, available RAM 10808 bytes (slot 0)
Software reset code 0x40b0 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f80f BFAR 0xe000ed38 SP 0x20001eac Task 0x5754454e
Stack: 0040611d 00406122 01000000 00000000 40e9f000 449ba533 00000000 3331bb4c c311e7c6 43d8eb1a bc000000 c00805c0 41f85a48 00000000 4762bd00 37d33333 4354c416 00000000 40b4c000 80000010 00406107 2001789c 00407001
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 30.7, current 31.1, max 31.3
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2019-09-22 18:01:14
Cache data hit count 44407538
Slowest loop: 1.47ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.54ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 84:f3:eb:41:59:80
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 24632
  WiFi IP address 192.168.0.43
  WiFi signal strength -36dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0: pos 0.00, no data received, no calibration data

when i get the sensor not working error and i do m122 this is the data for the filament monitor

Extruder 0: pos 234.14, ok, measured sens 25.61mm/rev min 97% max 101% over 18.1mm, errs: frame 18 parity 0 ovrun 0 pol 0 ovdue 0

even if the sensor is disabled i get this issue

Are you using the smart effector

its also worth noting that when the print gets paused i get the error M25 printing is already paused repeated over and over until i click cancel or resume

Ok here's the result

20/09/2019, 20:46:01: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04RC1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3SN-6J9FL-3S46J-1SYMD
Used output buffers: 3 of 24 (23 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93640 of which 284 recycled
Exception stack ram used: 312
Never used ram: 11156
Tasks: NETWORK(ready,652) HEAT(blocked,1172) MAIN(running,3756) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:00:26 ago, cause: power up
Last software reset at 2019-09-20 20:43, reason: User, spinning module GCodes, available RAM 11444 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 24.7, current 26.0, max 26.1
Supply voltage: min 24.1, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2019-09-20 20:46:01
Cache data hit count 78608853
Slowest loop: 5.02ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.43ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 84:f3:eb:41:59:80
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 25592
  WiFi IP address 192.168.0.43
  WiFi signal strength -35dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0: pos 0.00, no data received, no calibration data

it seems to be that once the print has been paused and resumed the next time i try to resume print it causes dwc to become unresponsive and a manual reset is required to obtain a connection again

im getting all sorts of crazy behaviour with this thing now causing resets when i click to resume print. i did have a laser monitor on my machine which worked it just didn't like any of the filaments i used so i thought it would be a straight switch out just change a few parameters in the config but i cant get it working at all

@dc42 it is firmware version 2.04rc1

Its like its constantly triggered and there is an orange light flashing which is not mentioned at all on the wiki

hi im trying to set the rotating magnet filament monitor up but everytime i start a print it pauses it wont even allow the heaters to heat up it just pauses constantlyconfig (3).g

hi thankyou i will do

hi is it possible to pay for items via bank transfer rather than paypal

@dragonn thankyou

Hi I'm just curious to know what programming language is the firmware for duet written in

@jackal interesting read thankyou