Well...... I'm dumb... swapped which spots the motors were plugged into and BAM. works great......

Moral of the story... don't be like me

So I have a 400X400 printer with two Z axis motors. I figured I would try to use them to help with bed compensation, they work great moving them up and down but when I run the calibration script it does the probing and then it compensates the wrong direction (it tilts the bed even further). I'm not sure why. Any thoughts?

CONFIG.G

; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves

M667 S1                                  ; Select CoreXY mode

; Network
M550 P"SpazCube"                         ; Set machine name
M552 P0.0.0.0 S1                         ; Enable network and acquire dynamic address via DHCP
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet


; Custom Configuration
M584 X0 Y1 Z2:4 E3                	; Set Z motors on drives 2 and 4
M671 X-30.0:430.0 Y0:0 S4 		; Set the Z motor relative locations
M208 X0:400 Y0:400			; X carriage moves from -5 to 205, Y bed goes from 0 to 200

; Drives
M569 P0 S1                               ; Physical drive 0 goes forwards
M569 P1 S1                               ; Physical drive 1 goes forwards
M569 P2 S1                               ; Physical drive 2 goes forwards
M569 P3 S0                               ; Physical drive 3 goes forwards
M350 X32 Y32 Z32 E16 I0                  ; Configure microstepping  without interpolation
M92 X200 Y200 Z799.10 E409               ; Set steps per mm
M566 X350.00 Y350.00 Z12.00 E3000.00      ; Set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z450.00 E3600.00  ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E5000.00       ; Set accelerations (mm/s^2)
M906 X800.00 Y800.00 Z900.00 E1000.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                         ; Set axis minima
M208 X400 Y400 Z500 S0                   ; Set axis maxima

; Endstops
M574 X0 Y0 Z0 S0                         ; Set active low and disabled endstops

; Z-Probe
M558 P9 H5 A5 F120 T6000                 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X60:350 Y50:350 S50                 ; Define mesh grid  
G31 P600 X59.5 Y0 Z2.10

; Heaters
M305 P0 T100000 B4138 R2200              ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                             ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R2200              ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                             ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 H-1 B1                     ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                            ; Define tool 0
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C

CALIBRATE CODE

; Warm Hotend and Bed
T0			; Select Tool 0
M104 S130		; Set Tool 0 temperature to 130 - no wait
M190 S60		; Set Bed temperature to 60 - wait

; Clear Values
G29 S2			; Clear Mesh Compensation Values
M290 R0 S0      	; Clear Baby-stepping

; Home all Axes
G28

; Bed leveling (G32)
G30 P0 X60 Y200 Z-99999 	; probe near a leadscrew
G30 P1 X360 Y200 Z-99999 S2 	; probe near a leadscrew and calibrate 2 motors

Hey guys! I just got my Wyze Cam installed and the firmware updated and it's working well. I enabled it on the duet and now I'm having some issues. The image only refreshes if I refresh the whole web page. I've got it set using https://xxx.xxx.xxx.xxx/cgi-bin/currentpic.cgi? (Using my correct IP of Course) and right now I have the update interval set to 1. Any info to help out would be great! Thanks!