Posts made by marioys97

@droftarts Hi,thanks for the help!
M122 output attached:

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.3 (2024-09-18 11:27:36) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 0JD2M-999AL-D25SW-6J1FA-3SN6R-1NX33
Used output buffers: 3 of 40 (33 max)
Error in macro line 87 while starting up: in file macro line 87: M570: missing parameter 'H'
=== RTOS ===
Static ram: 155352
Dynamic ram: 122240 of which 360 recycled
Never used RAM 64344, free system stack 122 words
Tasks: NETWORK(1,ready,37.4%,145) ETHERNET(5,nWait 7,1.7%,116) HEAT(3,nWait 6,0.0%,321) Move(4,nWait 6,2.8%,211) CanReceiv(6,nWait 1,0.0%,771) CanSender(5,nWait 7,0.1%,327) CanClock(7,delaying,0.0%,346) TMC(4,nWait 6,10.1%,53) MAIN(1,running,48.0%,444) IDLE(0,ready,0.0%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 51:01:37 ago, cause: power up
Last software reset at 2024-10-21 09:57, reason: User, Gcodes spinning, available RAM 65304, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 40.2, current 43.0, max 47.6
Supply voltage: min 23.1, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 99/6, heap memory allocated/used/recyclable 2048/184/24, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 152, reads 47780, writes 1 timeouts 0
Driver 1: standstill, SG min 0, mspos 152, reads 47781, writes 1 timeouts 0
Driver 2: standstill, SG min 0, mspos 152, reads 47781, writes 1 timeouts 0
Driver 3: standstill, SG min 0, mspos 152, reads 47781, writes 1 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 47782, writes 0 timeouts 0
Driver 5: standstill, SG min 0, mspos 696, reads 47780, writes 1 timeouts 0
Date/time: 2024-10-30 12:21:15
Slowest loop: 14.10ms; fastest: 0.07ms
=== Storage ===
Free file entries: 19
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.6ms, write time 1.0ms, max retries 0
=== Move ===
DMs created 125, segments created 35, maxWait 1590ms, bed compensation in use: mesh, height map offset 0.220, max steps late 0, min interval 0, bad calcs 0, ebfmin -0.00, ebfmax 1.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 8380705, completed 8380705, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x80000003
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 4351390, received 682766, lost 0, errs 0, boc 0
Longest wait 1ms for reply type 6023, peak Tx sync delay 673, free buffers 50 (min 49), ts 426725/426725/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 15.81ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 2 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0

Config:

; General Configuration
G90                            			; Absolute Coordinates  
M83                            			; Relative Extruder Movement
M550 P"my printer"						; Machine Name 

; Network Configuration
M540 P00:EE:FD:AD:DE:DH		; MAC Adress

M552 P192.168.101.127 S1           		; Fixed IP
M554 P192.168.0.1             			; Gateway 
M553 P255.255.0.0              			; Network Submask 
M586 P0 S1                     			; HTTP ENABLED 
M586 P1 S1                     			; FTP ENABLED
M586 P2 S0                     			; TELNET DISABLED

; Driver Configuration 
M569 P0.0 S1								; Default Configuration, S1=Reversed
M569 P0.1 S1
M569 P0.2 S1			
M569 P0.3 S1
M569 P1.0 S0
M569 P1.1 S0
M569 P1.2 S0
M569 P0.4 S1			 
M569 P0.5 S1
M584 Z0.0:0.1:0.2:0.3 X1.0:1.1 Y1.2 E0.5               		; Axis-Driver 
;M584 Z0.3 X1.0 Y1.2 E0.5               		; Axis-Driver 
; Motion Configuration
M564 S1 H1								; Movement only allowed after homing. Movement only allowed inside the axis limits
M208 X0 Y0 Z-1 S1            			; Axis Minimum
M208 X510 Y510 Z500 S0       			; Axis Maximum
M574 X1 S1 P"0.io0.in"  					; Xmin Endstop 
M574 Y1 S1 P"0.io1.in"   					; Ymin Endstop 

M92 X320.48 Y320.64 Z640 E405      		; Steps/mm
M350 X16 Y16 E16 Z16 I1		 			; 16X Microstepping. Interpolation Enabled 						

M566 X300 Y300 Z60 E120         		; Jerk (mm/min),
M203 X7000 Y7000 Z800 E1200    		; Maximum Speed (mm/min)
M201 X500 Y500 Z40 E250           	; Maximum Acceleration  (mm/s^2)
M906 X2000 Z1800 Y2000 E600      		; Axis Current (mA)

M671 X-423:-423:647:647 Y-27:533:533:-27 P5 S1  ; define leadscrews position
	
; Z-Probe (piezo) 
;M558 P1 C"!io6.in" X0 Y0 Z0 H15 T2000 F100 R1	; Declaración de probeta Smart IR, Probe Height=5, Feedrate=200
;M558 P1 C"!io6.in" X0 Y0 Z0 H5 T6000 F75 R2 B1; Declaración de probeta Smart IR, Probe Height=5, Feedrate=200   COMENTADO A DIA 18/04/2023 POR VICTOR
;M558 P1 C"!io6.in" X0 Y0 Z0 H5 T4000 F100 R2	; Declaración de probeta Smart IR, Probe Height=5, Feedrate=200
;G31 X0 Y0 Z0 P850					; Offsets de la probeta con respecto al nozzle, configuración NOVA           COMENTADO A DIA 18/04/2023 POR VICTOR

M558 P1 C"!io6.in" X0 Y0 Z0 H5 T6000 F100 R0.5	; Declaración de probeta Smart IR, Probe Height=5, Feedrate=200     NUEVO DIA 18/04/2023
m950 p2 c"io6.out"
G31 X0 Y0 Z-0.10 P850					; Offsets de la probeta con respecto al nozzle, configuración NOVA          NUEVO DIA 18/04/2023


M557 X0:500 Y0:500 S50:50  			; Height Map Limits. S = Spacing

; Sensor Declaration 
M308 S0 P"temp0" Y"thermistor" T65000 R2200 A"BED"				; Heated Bed Temperature Sensor Configuration
M308 S1 P"temp2" Y"PT1000" A"PT-1000"							; Nozzle Temperature Sensor Configuration
M308 S2 P"temp1" Y"PT1000"  A"CHAMBER"				; Chamber Heater Temperature Sensor Configuration 
M308 S3 P"temp3" Y"PT1000"  A"CHAMBER_TOP"				; Chamber Heater Temperature Sensor Configuration
M950 H0 C"out9" T0 														; Heated Bed Configuration  
M950 H1 C"out1" T1 														; Nozzle Configuration  
M141 H2                                                                 ; Configuracion como chamber Mario 13/12/2023
M950 H2 Q0 C"out7" T2:3													; Chamber Heater Configuration Mario 13/12/2023
M307 H2 B0 S1.00                                                        ; Disable bang bang mode, pwm a 1 Mario 13/12/2023
M143 H2 T3 S150 A2								; Prueba calefactor central, con PT1000 pegado al radiador. Corte a 150º Mario 13/12/2023
M570 H2 P10000 T60                               ; Deteccion heater fault , Mario 13/12/2023
M950 F1 C"out4"															; GpOUT for Thermostatic 
M950 F0 C"out6"															; GpOUT for Layer fans 
M950 P0 C"out8"															; GpOUT for Light
M950 P1 C"out5"															; GpOUT for Filter

; Fan Declaration 
M106 P0 S0 C"Layer Fan"     											; Layer Fan Declaration 
M106 P1 S255 H1 T150 C"Thermostatic fan "     								; Thermostatic Fan Declaration 

; Heaters Declaration 
M140 H0																	; Declares Heated Bed 
M141 H2																	; Declares Heated Chamber 
M307 H0 A64.3 C185.2 D3.6 S1 V25.6 B0									; Default Calibration of Heated Bed Model. 
M307 H1 A829 C261.3 D8.1 S1.00 V25.6 B0									; Default Calibration of Nozzle Model.  
M307 H2 B1 																; Default Calibration of Heated Chamber Model. 
M143 H0 S130                    										; Heated Bed Maximum Temperature 
M143 S500																; Nozzle Maximum Temperature 
M570 S180																; Nozzle Heater Timeout 
M570 H1 P50 S1000														; Heater Fault Configuration for Nozzle 
M570 H2 P600 S6000														; Heater Fault Configuration for Chamber 

; Declaration of TOOL 0 (DRAGON hotend with one layer fan, and thermostatic fan for FDM)
M563 P0 D0 H1 F1 S"FDM"                      					    	; Tool Configuration 
G10 P0 S0 R0 X0 Y0 Z0         											; Standby Parameters for Tool 0


;DHT Sensor 
M308 S5 P"io5.out" Y"dht22" A"Filament Temp" ; define DHT22 temperature sensor
M308 S6 P"S5.1" Y"dhthumidity" A"Filament Hum[%]" ; Attach DHT22 humidity sensor to secondary output of temperature sensor
; Advanced ConfigurationS  
M572 D0 S0.10															; Pressure Advance (Calibrated Value)
M911 S23 R22 P"M28 0:/sys/resurrect-prologue.g"						; Power Loss Configuration 

; Triggers  
M950 J0 C"io5.in"														; Photoelectric sensor to check if doors are opened  
M581 P0 T1 R1 S1														; Trigger function when the doors are opened 	
M581 P0 T2 R1 S0														; Trigger function when the doors are closed 
	

M17																		; Enable Motors
M501																	; Charges parameters from the EEPROM (config-override)		
G29 S1																	; Charges mesh
M42 P0 S1
T0																		; Selecciona Tool 0 por defecto

Hi everyone, I am having some issues when I pause my prints.
Sometimes I pause the print and it executes the whole pause.g file without problem, but sometimes it only pauses the print in the same place the printhead is at that moment, not executing the pause.g file.
Sometimes it also executes the whole pause.g filebut it looses home in all the axis and shuts off both bed and printhead heaters.
Currently running 3.5.2.
Pause.g file:
M83 ; movimietnos relativos del extrusor
G1 E-5 F3600 ; Se retraen 10mm de filamento
G91 ; Coordenadas relativas
G1 Z30 F360 ; Se levanta el cabezal 30mm
G90 ; Coordenadas absolutas

@chrishamm Thanks!

Hi everyone, I am currently developing an "AMS" system with my duet3d setup. I want to run filaments assigning into the system but I am finding the following limitation:
"Filament assignments can be only made for tools that have exactly one extruder drive assigned. This limitation ensures that the load and unload macros work with each extruder drive." (found on DUET3D filament docs)

Is there a way to solve this limitation?

Hi everyone, I am currently assembling a machine with Duet 3 Motor23 CL motors. Although I can comunicate with them and make them move, I keep getting the following error:

Does anyone knows how to solve this issue?

@jay_s_uk Hi Jay, thank you very much but my concern is to comunicate two mainboards that run different prints. Just simple commands comunication.

@jay_s_uk Hi! How could I do that?

Hi everyone, is there a way to comunicate several Duet3 boards?

Hi, I`m using two bed heaters for mi heated bed. Is it possible to make an average of the two thermistors to control both of them as one unique heated bed?

Hi, I need to control an external device with current modulation from 0 to 85 mA. Is there a way I can control it with a Duet3???

Thanks in advance

@pcr it does light up, it makes a couple of deploys and rectracts and then it stops working. The red led is light up but then it doesn´t do anything when I run m280 commands

everything is connected to io5 port. Brown and black are connected to GND, red to 5v, yellow to io5.out and white to io5.in

@t3p3tony everything is connected as that guide explains. I`m connecting everything to the io5 port. The deployprobe and retract are located at sys folder being m280 p0 s90 and m280 p0 s10.

Hi I'm trying to use a BLTouch on a DUET3 6HC but it can't make it work. This is my config
M558 P9 C"^io5.in" H5 F100 T2000
M950 S0 C"io5.out" ; Servo
G31 P25 X0 Y55 Z2