@droftarts Dear Ian, I made it. It worked. I used a DuetPi image and I could flash the 6HC. A bit tedious and I hope that the normal flashing works for the next firmware version. Many thanks for your help and guidance. Would not have been able to do it without you. Thanks.
Best posts made by marcel.kastler
-
RE: Upgrade to 3.5.3 failed
-
RE: Upgrade to 3.5.3 failed
@droftarts Dear Ian, your efforts are highly appreciated. However, I consider now to use my 6HC in SBC mode, since I bought a new raspberry. Then firmware updates hopefully become less of a problem since Bossa worked like a charm on your raspi OS.
Latest posts made by marcel.kastler
-
RE: Upgrade to 3.5.3 failed
@droftarts Dear Ian, your efforts are highly appreciated. However, I consider now to use my 6HC in SBC mode, since I bought a new raspberry. Then firmware updates hopefully become less of a problem since Bossa worked like a charm on your raspi OS.
-
RE: Upgrade to 3.5.3 failed
@droftarts Dear Ian, I made it. It worked. I used a DuetPi image and I could flash the 6HC. A bit tedious and I hope that the normal flashing works for the next firmware version. Many thanks for your help and guidance. Would not have been able to do it without you. Thanks.
-
RE: Upgrade to 3.5.3 failed
@droftarts Hi Ian, yes, quite tedious to get the board back running. Just to confirm. Should I connect the Duet 6HC board via USB to the raspberry pi or should I use the flat ribbon cable, which was included with the duet board?
-
RE: Upgrade to 3.5.3 failed
@Phaedrux Good morning, I organised myself a raspberry pi, but ran into the next problem and need your guidance.
I receive a fatal error installing Bossa on the board. I reinstalled the OS to the raspberry, but I get the same error and cannot continue. No idea what to do now. Here the error:marcel@voron2:~ $ sudo apt update && sudo apt install -y libwxgtk3.0-dev libreadline-dev
git clone https://github.com/shumatech/BOSSA
cd BOSSA
make
Hit:1 http://deb.debian.org/debian bookworm InRelease
Get:2 http://deb.debian.org/debian-security bookworm-security InRelease [48.0 kB]
Get:3 http://deb.debian.org/debian bookworm-updates InRelease [55.4 kB]
Get:4 http://deb.debian.org/debian-security bookworm-security/main armhf Packages [191 kB]
Get:5 http://deb.debian.org/debian-security bookworm-security/main arm64 Packages [187 kB]
Get:6 http://deb.debian.org/debian-security bookworm-security/main Translation-en [116 kB]
Get:7 http://archive.raspberrypi.com/debian bookworm InRelease [39.2 kB]
Get:8 http://archive.raspberrypi.com/debian bookworm/main armhf Packages [533 kB]
Get:9 http://archive.raspberrypi.com/debian bookworm/main arm64 Packages [503 kB]
Fetched 1569 kB in 3s (482 kB/s)
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
42 packages can be upgraded. Run 'apt list --upgradable' to see them.
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
Package libwxgtk3.0-dev is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another sourceE: Package 'libwxgtk3.0-dev' has no installation candidate
Cloning into 'BOSSA'...
remote: Enumerating objects: 1727, done.
remote: Total 1727 (delta 0), reused 0 (delta 0), pack-reused 1727 (from 1)
Receiving objects: 100% (1727/1727), 1.15 MiB | 5.62 MiB/s, done.
Resolving deltas: 100% (1321/1321), done.
make: wx-config: No such file or directory
make: wx-config: No such file or directory
CPP APPLET src/WordCopyArm.cpp
CPP COMMON src/Samba.cpp
CPP COMMON src/Flash.cpp
CPP COMMON src/D5xNvmFlash.cpp
CPP COMMON src/D2xNvmFlash.cpp
CPP COMMON src/EfcFlash.cpp
CPP COMMON src/EefcFlash.cpp
CPP COMMON src/Applet.cpp
CPP COMMON src/WordCopyApplet.cpp
CPP COMMON src/Flasher.cpp
CPP COMMON src/Device.cpp
CPP COMMON src/PosixSerialPort.cpp
CPP COMMON src/LinuxPortFactory.cpp
CPP BOSSA src/BossaForm.cpp
In file included from src/BossaForm.cpp:8:
src/BossaForm.h:11:10: fatal error: wx/artprov.h: No such file or directory
11 | #include <wx/artprov.h>
| ^~~~~~~~~~~~~~
compilation terminated.
make: *** [Makefile:260: obj/BossaForm.o] Error 1 -
RE: Upgrade to 3.5.3 failed
@Phaedrux Hi, currently no free raspberry pi. I have one older Intel based Mac.
-
RE: Upgrade to 3.5.3 failed
Is there someone from Duet3d who has a solution for my problem, please?
-
RE: Upgrade to 3.5.3 failed
@jay_s_uk I bought it directly from the UK.
-
RE: Upgrade to 3.5.3 failed
@jay_s_uk OMG. I hope Duet3d is working on a fix for Mac users… Is it possible to ask Duet to reflash my board or exchange it for me?
-
RE: Upgrade to 3.5.3 failed
@jay_s_uk thanks again. It looks very complicated with MacOS and not sure if it works at all. Is there no other solution? I do not want to spend hours to get my printer up and running. I always use the latest stable firmware to avoid trouble… which did not work this time.