@jay_s_uk It looks like that fixed it THANK YOU!

@jay_s_uk It looks like that fixed it THANK YOU!

[RESOLVED]

Hi All, getting this issue when using the Duet Web Interface after upgrading to a BLTouch. "M568 P0 A2 - The M568 command is no longer needed." when trying to turn on the heater for tool 0 or when trying to pre-heat.

My config nor pre-load, load, or unload, have any references to M568 so I'm at a bit of a loose end. I don't think it's to do with the bltouch but possibly something to do with the firmware & web interface version?

I used the Reprap Config Tool version v3.3.16 and am running Duet Web Control 3.4.6 and board firmware RepRapFirmware for Duet 3 Mini 5+ 3.2 (2021-01-05)

I can provide a screenshot of the error and a copy of the config.g file but I don't know how to upload them here yet! Edit: Added config.g ! Tried to link screenshot.

Thanks in advance all!

Link to image on google drive. Any suggestions on how to embed?

; Configuration file for Duet 3 Mini 5+ (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun Oct 29 2023 13:22:55 GMT+0000 (Greenwich Mean Time)

; General preferences
G90                                         ; send absolute coordinates...
M83                                         ; ...but relative extruder moves
M550 P"Locke Printer"                       ; set printer name

; Network
M551 P"***********"                           ; set password
M552 P0.0.0.0 S1                            ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                  ; enable HTTP
M586 P1 S0                                  ; disable FTP
M586 P2 S0                                  ; disable Telnet

; Drives
M569 P0.0 S0                                ; physical drive 0.0 goes backwards
M569 P0.1 S0                                ; physical drive 0.1 goes backwards
M569 P0.2 S1                                ; physical drive 0.2 goes forwards
M569 P0.3 S0                                ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3                    ; set drive mapping
M350 X16 Y16 Z16 E16 I1                     ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E93.00            ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E300.00         ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E3600.00     ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E2500.00       ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E900 I30                ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 X0 Y25 Z0 S1                            ; set axis minima
M208 X215 Y235 Z260 S0                      ; set axis maxima

; Endstops
M574 X1 S1 P"io5.in"                        ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io5.in
M574 Y1 S1 P"io6.in"                        ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io6.in
M574 Z1 S2                                  ; Use zprobe

; Z-Probe
M950 S0 C"io3.out"                          ; Set Z probe PWM Out
M558 P9 C"io3.in" H5 F120 T6000             ; set Z probe type to modulated and the dive height + speeds

G31 P500 X-50.25 Y-32 Z0.250; set Z probe trigger value, offset and trigger height
M557 X0:165 Y55:220 P20                    ; define mesh grid
M280 P0 S90 ; send control signal to BLTouch through servo/gpio 0

; Heaters
M308 S0 P"temp0" Y"thermistor" T98801 B4185 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                          ; create bed heater output on out0 and map it to sensor 0
M307 H0 R0.304 C431.4 D3.51 S1.00 V23.7     ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                     ; map heated bed to heater 0
M143 H0 S120                                ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                          ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 R5.078 C181.2 D3.09 S1.00 V23.9     ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S250                                ; set temperature limit for heater 1 to 250C

; Fans
M950 F0 C"out3" Q500                        ; create fan 0 on pin out3 and set its frequency
M106 P0 C"PARTFAN" S0 H-1                   ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out4" Q500                        ; create fan 1 on pin out4 and set its frequency
M106 P1 C"HOTEND" S1 H1 T45                 ; set fan 1 name and value. Thermostatic control is turned on

; Tools
M563 P0 S"HotEnd" D0 H1 F0                  ; define tool 0
G10 P0 X0 Y32 Z0                             ; set tool 0 axis offsets
G10 P0 R0 S0                                ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined