Posts made by Magnusjen

@dc42 It worked finally I am setting up the axis etc. hopefully tommorow I will start my first duet print

@magnusjen

Waaait a minute... I am in bed now and was just thinking cant i just take the SD card and configure IT without password?

I got my replacement duet wifi board because the other was defective (yay)! I went through the whole setup again and put in the config file. But wanted to reconfigure it, when I did this it asked for the password. I gave it the password and then another million times and it refuses.. So I tried connecting with USB and via YAT change the password using M551 Pnnn but this didnt work either. I have tried looking around the forum, but you put "wifi" and "password" in the same search and it is cluttered with other searches..

So, basic question is, how do I gain access to the interface when it won't accept the simple password I gave it?

Best regards
Magnus

@dc42 Thank you for your assistance, hopefully I can get the next to function and can post more interesting questions

@dc42 Hi, that is an amazing offer! I bought it Friday last week (2019.03.08) from RepRap.me in Denmark, they are one of your vendors in Denmark and I could not imagine them selling a knock off.

How do I go about the warrenty replacement?

@elmoret Hi there, here is a picture of the board from above, if you guys need it I can unplug everything.

@dc42 Thanks for replying, you got the situation right, I will upload a picture of my board aswell as another guy commented.

The extruder heater heats up fine, I checked both at the nozzle "to see it was just an IT lie" and DWC reports the heating. I have taken a screenshot of my DWC.

I would be happy if whatever mistake I have made can be corrected, you guys have made an awesome board.

I could not also add the picture of my board, I will do it as a reply to the other guy

@tenjin Hi there, no I don't have an LCD and I have nothing going into the 10 pin connector.

@veti Well, sounds like I will just wire my old control board up if that is the case and wait for new electronics parts to arrive and the perfect day to sit super calm and solder it on.

But good to know there is a fix, I will just wait for DCs comment.

@genghisnico13 Yeah... I have lost hope, I am just waiting for someone to confirm it is dead.. I will take it as an expensive lesson in basic wiring.

@genghisnico13 So, the top picture one is 24V (23.7 is the reading I get all the time but thats 24V) and the one in the lower picture is 23.5 which is odd, I measured it several times to ensure it was correct.

@phaedrux I have tested the fuses and the resistance is zero as it should be if it is working.

Just got home from work (will just do continues updates here in the hope that someone will see and have an idea/using it as a log in case someone wants to chim in).

I have done a "visual" inspection of the board, everything seems to be in order nothing that looks burned or shorted.

The DWC still reports 0.5 V, but I can activate both hotend and heatbed.. But not my motors. So power is clearly going somewhere but not to the motors.

I will look into if the fans can work - Ah... there we might have it.. I think I have fried the board at the fans.. I cannot get my fan to work on any position, neither always on or any of the others... Is there a way to confirm this?

Status on the Issue
I am using a DUET 2 WIFI 1.03 with newest firmware (non-beta) - on an Ender 3 pro, the power supply is the Ender 3 Pros. The fans are the Ender 3 stock fans which are all 24V. I used hooked these up to the board, but did several wrong wirings ( I think), I even tried to hook up a 5V fan without changing the jumper nothing happend. After this the motors were still working. I turned the board off and tried to rewire the fans that did not work, the next day I turn the board on and I get the error and DWC showing 0.5 V.

The issue:
When I try to move the motors it says "Attempt to move motors when VIN is not in range"

DWC shows 0.5 V in VIN
I have tested all fuses they show zero ohm
I have measured power in and it shows 24 V
I have measured from power to heatbed and it shows 24V
I have measured from power to hotend and it shows 24V
Wifi Blue light check
3.3V green light check
5V red light check
VIN blue light check
Z,Y, X stop red lights check
I have checked that VIN is tight (it is tight..)
All jumpers are in "stock" positions

So... Thats about where we are at... Help me DUET forum, you are my only hope... I just wanna know if it is dead and I have to try again

So I noticed something fun... It actually reads as 0.5 V in the web interface, which makes even less sense to me. I haven't touched any of the jumpers, they are the way I got them.

I have made a post with a similar issue and haven't been able to solve it. I have a 24V power supply but when I look in the interface it says 0.5V and the same "attempt to move blah blah..."

Just a random update, to those following along.. I checked the voltage from the PWN in (which comes in at 24V still) against the heatbed, the heatbed also says 24V... I checked against an always on fan pin and got a tiny spark... I will just stop checking voltage for a little while.

The console still shows 5V.. I have tried unplugging everything from the board (why? Why not) and the console still shows 5V. I am going slightly insane here.

@danal Thanks for the help so far bud! I will go and run some errands while I wait for them to be online.. I am stumped myself, but I am happy this forum exists! I really want the board to work it seems so great.

@danal Good timing, I was just about to put one on hehe

@danal jumper??? There never was a jumper there on my board.