@phaedrux
When I install FW 3.2.2 , it works fine.
seem like a bug in FW3.3beta2 and 3.3beta3 (both give the same error back)
Latest posts made by ludo
-
RE: Thermocouple M308: string too long 3.3 betaposted in Beta Firmware
-
Thermocouple M308: string too long 3.3 betaposted in Beta Firmware
Hi,
I have a Duet 6hc motherboard, and a thermocouple connected to the thermocouple daughterboard V1.1
Firmware Name: RepRapFirmware for Duet 3 MB6HC
Firmware Electronics: Duet 3 MB6HC v0.6 or 1.0
Firmware Version: 3.3beta2 (2021-03-10)
WiFi Server Version: n/a
Web Interface Version: 1.22.6the output for bedtemp is always 2000°C
; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Mon Aug 31 2020 15:45:57 GMT+0800 (中国标准时间) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Big-40" ; set printer name ; Network M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; Physical drive 0 goes forwards. X-Axis. M569 P1 S0 ; Physical drive 1 goes backwards. Y-Axis. M569 P2 S0 ; Physical drive 2 goes backwards. ZL-Axis. M569 P3 S0 ; Physical drive 3 goes backwards. ZR-Axis. M569 P4 S1 ; Physical drive 4 goes backwards. E0-Extruder. M569 P5 R-1 ; Physical drive 4 goes backwards. E0-Extruder. M584 X0 Y1 Z2:3 E4 ; set drive mapping M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y100.00 Z2000.00 E418.500 ; set steps per mm M566 X240 Y360 Z30.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z360.00 E1200.00 ; set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z120.00 E250.00 ; set accelerations (mm/s^2) M204 P500 T1000 ; Set print and travel accelerations (mm/s^2) M906 X1800.00 Y1800.00 Z1800.00 E1000.00 I40 ; set motor currents (mA) and motor idle factor in per cent M84 S60 X Y E0 ; Set idle timeout ; Axis Limits M208 X0:400 Y0:400 Z0:800 ; set axis maxima ; Endstops M574 X1 S1 P"io1.in" ; configure active-high endstop for low end on X via pin io1.in M574 Y1 S1 P"io2.in" ; configure active-high endstop for low end on Y via pin io2.in M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"io4.out" ; create servo pin 0 for BLTouch M558 P9 C"^io4.in" H5 F120 T9000 A1 R0.7 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X-14 Y21 Z1.503 ; set Z probe trigger value, offset and trigger height M557 X-14:382 Y21:417 S66 ; define mesh grid M376 H10 ; Height (mm) over which to taper off the bed compensation ; Heaters M308 S0 P"spi.cs2" Y"thermocouple-max31856" T"K" F50 ; define temperature sensor number 0 as a K Type M950 H0 C"out3" T0 ; create bed heater output on out3 and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C ;Extruder0 M308 S1 P"spi.cs1" Y"rtd-max31865" F50 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 R2.146 C220.3 D4.33 S1.00 V23.9 M143 H1 S400 ;MCU M308 S2 Y"drivers" A"DRIVERS" ; configure sensor 2 as temperature warning and overheat flags on the TMC2660 on Duet M308 S3 Y"mcu-temp" A"MCU" ; configure sensor 3 as thermistor on pin e1temp for left stepper M950 F2 C"out4" Q500 ; create fan 2 on pin "out4" and set its frequency M106 P2 H2:3 L0.15 X1 B0.1 T40:70 ; set fan 2 to turn on at 40° and goes proportionally to full speed at 70° ; Fans M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency M106 P0 S0 H-1 C"Part Fan" ; set fan 0 value. Thermostatic control is turned off M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency M106 P1 I-1 C"Led" ; Disable fan channel for LED ; Tools M563 P0 S"Extruder" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S210 ; set initial tool 0 active and standby temperatures to 0C ;M563 P1 D5 H2 F1 ; define tool 1 ;G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets ;G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C ;M563 P2 D2 H3 F2 ; define tool 2 ;G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets ;G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C ; Automatic power saving____________________________________________ M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss. Power Failure Pause ; Custom settings are not defined ; Miscellaneous M591 D0 P1 S1 C"io5.in" ; Regular filament sensor for E0 M575 P1 S1 B57600 ; enable support for PanelDue ;M564 H0 M302 P1 ;Allows cold extrudeswhen I do M98 P"config.g"
I get the following response
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: in file macro line 53 column 43: M308: string too long
Warning: Sensor number 0 has not been definedwhat am I doing wrong?