Posts made by luc

I had read about some problems on RRF 3.2.2. As soon as I have a moment I update both of them and hopefully well.
Thanks everyone for the answers.

Hi guys, I have a duet 2 wifi with 3.1.1 firmware and I use Duet Web Control 3.1.1 and I would like to know if I can install DWC 3.2 without updating the firmware to 3.2 or if I need to update both.
Thank you

@Turbo Listen ... I don't speak English well but I presented you my experience of my case where I wrote that I also did the continuity and isolation tests several times and they were always ok but your case is perhaps different.

Hi .... it also happened to me in a previous printer, I also changed the power supply only to discover that it was a false contact in the motor cables. I changed them directly even if measuring them several times with the tester (at that moment) they were always ok.
Now, I don't know if this could also be your cause but if you think it appropriate you could try it.

@Phaedrux Ok..... Only during a failure condition....

@Phaedrux Hi, maybe I say something not exact but I'm always looking for a solution by character. There is a value in the PID M307 which indicates the power of the heating phase which by default is 100%. If you decrease example to 80%, could it no longer give the warning? It might take a little longer to heat up but would you have other problems?

ok ... i solved. It was because of the config.override. I sent an M500, the file updated and the "Heaters x not found" errors disappeared. It remains the "warnig Heater 1 but I should resolve with a new pid.

Unfortunately I agree that I have the following errors:

5/10/2020, 08:48:48 M98 Pconfig.g
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 790C
Error: Heater 2 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found

On Heater 0 and 1 I think I understand what it is (maybe even PID to be redone) but for Heater 2-4-5 and 6 what should I check?

@Phaedrux Hi, I loaded 3.1.1 and then the new config, home, etc ...... everything worked right at the first try! This is a satisfaction both for me and for you who have patiently supported me. Thank you again!

The PIDs remain to do and move the 3 Z motors but I will do it later when I have some free time.

In the meantime I ask what "Mode: FFF" means in DWC (top right)

I don't know if it was there before but I hadn't noticed.

The initial (basic) configuration with the configurator (excluding duex) was very useful for me but I find it much better to use the Gcode guide to make additions and / or changes. It is also easy.
Only the references to the duex seem to me (for my way of doing but maybe I'm wrong) a bit limited. I have yet to understand its logic.

@Phaedrux Ok, I get it, just motors. But to learn the command syntax for duex is it correct as I wrote above? How was I supposed to write?

Thank,
Sorry, I didn't explain. I only meant the gcode part with examples on extruder, fans, temperature probe, etc.

Hi, where do I find a guide to configure duex for both RR2 and RR3?

@Phaedrux said in Doubt due to passage from 2.05.1 to 3.1.1:

Having M584 on two lines is fine. What I would change, as I said before, would be having all the Z axis motors on the mainboard and the extruders on the duex.
M584 X0 Y1 Z2:3:4 E5:6

Please @Phaedrux , tell me if the shift from E0 from duet2 (E3) to duex (E5) is correct:

On duet2
Hotend:
M308 S1 P "e0temp" Y "thermistor" T100000 B3950
M950 H1 C "e0heat" T1
M307 H1 B0 S1.00
M143 H1 S280

Fan cools print:
M950 F0 C "fan0" Q500
M106 P0 S0 H-1

On duex2
Hotend:
M308 S1 P "exp.heater3" Y "thermistor" T100000 B3950
M950 H1 C "e0heat" T1
M307 H1 B0 S1.00
M143 H1 S280

Fan cools print:
M950 S0 C "duex.fan3"
M106 P0 S0 H-1

Okay or did I miss something on the way?
Thanks again.

@Phaedrux said in Doubt due to passage from 2.05.1 to 3.1.1:

@luc said in Doubt due to passage from 2.05.1 to 3.1.1:

M106 P1 S1 H-1

The hotend fan would stay as you have it fr thermostatic control. M106 P1 S1 H1 T45.

Thank you very much

@dc42 said in Doubt due to passage from 2.05.1 to 3.1.1:

@luc said in Doubt due to passage from 2.05.1 to 3.1.1:

For paneldue: I installed firmware 1.23.2 and I'm not sure if I necessarily have to install 1.24. Do I need to update?

AFAIR, 1.23.2 will is OK with RRF 3.1.1 on a Duet 2. Version 1.24 is necessary on Duet 3 systems with both a PanelDue and an attached single board computer.

Thank you very much

@Phaedrux said in Doubt due to passage from 2.05.1 to 3.1.1:

.....What I would change, as I said before, would be having all the Z axis motors on the mainboard and the extruders on the duex.
M584 X0 Y1 Z2:3:4 E5:6

OK...now I got it. I thought you thought I had duex5 and you wanted to tell me to place the 3 Z motors in the duex. I will follow your advice.

duex.pwm1 looks ok for the BLtouch. Will need to test first obviously.

ok, of course.

heater and thermistors look ok if you have NTC3950 100K thermistors. Be sure to do a PID tune for the heaters.

Yeah ... I have these right now. I will definitely do the PID related to hotend and bed.

Fan block was correct before, but now they are both set to thermostatic control. The part cooling fan should have H-1 and no T parameter to disable thermostatic.

Thanks .... I correct (M106 P0 S0 H-1 / M106 P1 S1 H-1)

Tools start with T0, you only have one tool so T0 is your first tool, you have no T1.

I seem to remember that I had a problem with the display in the paneldue 5i and had to put T1 in the RR2 as something was not showing but I'm not sure about that.

Please allow me another question:

• For paneldue: I installed firmware 1.23.2 and I'm not sure if I necessarily have to install 1.24. Do I need to update?

Many thanks for your availability .... I don't know if it will happen (I'm in Italy) but you have two paid beers !!!

ok .... according to your suggestions I have better checked the draft of the config.g for V3. I also followed the page: https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Summary_of_what_you_need_to_do_to_convert_your_configuration_and_other_files

This would be a new version: config V3.g

I would like your opinion on the following points:

• M584: is it correct on two lines as I wrote or does it all go on one line (M584 X0 Y1 Z2:5:6 E3)?

• Zprobe section: bltouch use connected to duex2 on pvm1. I'm not sure about the MM950 S0 C"duex.pwm1" and M558 configuration

• Bed and Hotend heaters: are they ok?

• Fans: I only have two simple fans. One always on which cools the hotend body and the other for cooling the piece being printed. Is the configuration correct?

• "And you should add a T0 to the end of config.g to select your first tool at startup." In the RR2 I use T1. Should I change to T0?

Sorry for too many questions Any other suggestions are welcome

Thanks again for your availability.
Yes, reading I understood that:

• For duet2wifi I have to install V3.0.0 first and then 3.1.1;
• For paneldue I installed 1.23.2 and I'm not sure if I necessarily have to install 1.24. Do I need to update? ;

For the conversion of config.g

• This is the configuration of the working V2: config V2.g

• This is a draft of the V3 configuration that I am preparing and on which I ask you for help for verification: config V3.g

Note: I use 3 Z motors: 1 connected directly to duet2 and 2 motors connected to duex2

Will I need to make any changes to the homex, homey, homez, homeall, bed .... files?

@droftarts First of all thanks for your answer.
For the features I currently use today 2.05.1 is sufficient but I would like to upgrade to 3.XX. I had some fun simulating the configuration for 3.1.1 using the online configurator and manually modifying / adding parameters. If I attach the config.g of version 2 (working) and version 3 (simulated) do you have time to give me your opinion on any errors?

(I wish that by installing V3 everything already works)