@phaedrux

I am good now. I changed out the usb cable and it worked just fine. I thought because I had all the right led's everything else was fine.

@pungoboy

Hello are you still open to repairing boards?

Kevin
kthoma85@gmail.com
8104346684

@phaedrux Thank you so much for that direction. I should be able to fix my issue with the info provided. And again, thank you.

Kevin

My printer has the X axis limit switch to the left hand side of the printer. But since switching over to the Duet, my printer wants to home to the right. How can I change the direction of the motor when homing?

You were correct. I had it configured as a XZ
.

I have a Creality CR10 v2. I pulled all the connections from the original controller nd display. I am now connected to my Duet2 ethernet and Due Panel 7.When I move my Z motors my X motors move in the same direction as well. So if I move my Z motors 50mm my x motors move 50mm. All three motors are being commanded whether I tell the X or the Z motors to move. Any suggetsions?

@phaedrux

I am good now. I changed out the usb cable and it worked just fine. I thought because I had all the right led's everything else was fine.

Hello All,

I am trying to connect to a Duet2 I purchased a while back. I connect the USB cable to the board and I get the two red led's for 5+v and the green led for 3.3+v, but I cannot get Yat to connect to the board. I also tried the other program that starts with a P. both say the printer is off line. Reading in your connections help section I believe I am at the point of erasing everything, I juat want to make sure there is nothing left for me to try. The board does not appear in my device manager no matter what I have tried. I have plugged the board into four different USB ports.

Yes, I checked the link and I don't have an M911 in my config. I have the same config file that came with the board with only the M552 is changed to P0.0.0.0 instead of the factory setting.

; Configuration file for factory testing Duet Ethernet and Wifi with V2.01 firmware

---

FOR TESTING ONLY! USE https://configurator.reprapfirmware.org/ to generate configuration files for your printer!

---

; Communication and general
M111 S0 ; Debug off
M550 PDuetTest ; Machine name and Netbios name (can be anything you like)
M551 Preprap ; Machine password (used for FTP)

*** Ethernet networking: The following lines are used for factory testing - PLEASE REMOVE THEM
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
M552 P0.0.0.0 ; IP address
M554 P192.168.1.255 ; Gateway
M553 P255.255.255.0 ; Netmask

;*** End of factory test lines to be removed

;*** Networking
M552 S1 ; Turn network on

M555 P2 ; Set output to look like Marlin
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

; Disable Fan 1 thermostatic mode
M106 P1 H-1

; Axis and motor configuration
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
;*** The homed height is deliberately set too high in the following - you will adjust it during calibration
M665 R105.6 L215.0 B85 H250 ; set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
M350 X16 Y16 Z16 E16:16 I1 ; Set 16x microstepping with interpolation
M92 X80 Y80 AZ80 ; Set axis steps/mm
M906 X1000 Y1000 Z1000 E800 I60 ; Set motor currents (mA) and increase idle current to 60%
M201 X1000 Y1000 Z1000 E1000 ; Accelerations (mm/s^2)
M203 X20000 Y20000 Z20000 E3600 ; Maximum speeds (mm/min)
M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute

; Thermistors
M305 P0 T100000 B3950 R4700 H30 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
M305 P1 T100000 B3974 R4700 H30 L0 ; Put your own H and/or L values here to set first nozzle thermistor ADC correction
M305 P2 T100000 B3974 R4700 H30 L0 ; Put your own H and/or L values here to set 2nd nozzle thermistor ADC correction

M570 S180 ; Hot end may be a little slow to heat up so allow it 180 seconds

; Adjustments for dummy heaters on test rig
M307 H0 A250 C140 D5.5 B1
M307 H1 A250 C140 D5.5 B0
M307 H2 A250 C140 D5.5 B0

; Fans
M106 P1 S-1 ; disable thermostatic mode for fan 1

; Tool definitions
M563 P0 D0 H1 ; Define tool 0
G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures
;*** If you have a single-nozzle build, comment the next 2 lines
M563 P1 D1 H2 ; Define tool 1
G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures
M92 E80:80 ; Set extruder steps per mm

; Z probe and compensation definition
;*** If you have a switch instead of an IR probe, change P1 to P4 in the following M558 command.
M558 P5 F100 T6000 X0 Y0 Z0 H3 ; Z probe is a Smart Effector and is not used for homing any axes R0.4 not used. Reduced F300 to 100
G31 P100 X0 Y0 Z-0.25 ; Set the zprobe height and threshold for Smart Effector

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0 ; Axis compensation here

M208 S1 Z-0.2 ; set minimum Z

T0 ; select first hot end
; M117 Use https://configurator.reprapfirmware.org/ to set up your printer config

Thank you everybody. I am good to go now.

I found the IP address assigned to the Ethernet and sent put it in through YAT. Only now when I disconnect the usb cable from teh DUET2 and power the board with my power supply YAT no longer has a comm port. How do I get web controller to communicate via the Ethernet connection?