@diy-o-sphere sorry i miss typed there of course i meant higher xD, but i already sorted it out... i updated the firmware and somehow it's working again i don't know what the issue was but it's fixed know

@Phaedrux Thanks for answering, updated dwc and firmware and it's going!

@tas thank you very much, updated dwc and the printer firmware and it's working! next step is fine tuning!

Hey Guys, im trying to get the Input Shaper running on my Printer, but when im trying to record an motion profile, it says : "Error: M956: Failed to start accelerometer data collection" and I don't know why. I'm using a Duet 3 Mini 5+ with RRF and DWC 3.5.0-beta.3, and an LIS3DH Accelerometer. I would appreciate your help.

@diy-o-sphere sorry i miss typed there of course i meant higher xD, but i already sorted it out... i updated the firmware and somehow it's working again i don't know what the issue was but it's fixed know

Hey,
first of all, i have an Ender 3 with an Duet 3 Mini 5 +. I already had it running for a few months, but a few days ago it started printing higher than usual so the distance between nozzle and bed was bigger than before. Though i have nothing changed in my settings, so i tried to lower the trigger height to get closer to the bed. But it didn't change anything it literally stopped at the same height. I hope someone can help me.

Here is my Config and my Homez file

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Fri Jun 24 2022 15:52:30 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Ender 3" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display

; Network
M552 S1 P"TP-Link_CE46" ; enable network
M587 I"192.168.1.42"
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S0 D3 V40 ; physical drive 0.0 goes backwards
M569 P0.1 S0 D3 V40 ; physical drive 0.1 goes backwards
M569 P0.2 S1 D3 V40 ; physical drive 0.2 goes forwards
M569 P0.3 S0 ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E3600.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E2500.00 ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X220 Y220 Z250 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"io5.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io5.in
M574 Y1 S1 P"io6.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io6.in
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"io3.out" ; create servo pin 0 for BLTouch
M558 P9 C"io3.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X48 Y-2 Z0.30 ; set Z probe trigger value, offset and trigger height
M557 X20:200 Y20:200 S40 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T98801 B4185 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M308 S1 P"temp1" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250 ; set temperature limit for heater 1 to 250C

; Fans
M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency
M106 P0 C"PartCooling" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out5" Q500 ; create fan 1 on pin out5 and set its frequency
M106 P1 C"HotEnd" S1 H1:0 T45 ; set fan 1 name and value. Thermostatic control is turned on
M950 F2 C"out6" Q500 ; create fan 2 on pin out6 and set its frequency
M106 P2 C"CaseFan" S1 H1:0 T45 ; set fan 2 name and value. Thermostatic control is turned on
M950 F3 C"out4" Q500 ; create fan 3 on pin out4 and set its frequency
M106 P3 C"LEDs" S1 H-1 ; set fan 3 name and value. Thermostatic control is turned off

; Tools
M563 P0 S"HotEnd" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
M204 P600 T2000 ; Set accelerations (mm/s^2) for print and travel moves
M912 P0 S-13 ; CPU temperature calibration
M572 D0 S0.35 ; Pressure Advance
M207 S6.5 R0.0 F4800 T4800 Z0.0 ; Retraction
M280 P0 S160 ; Clear any alarms
M402 ; retract pin just in case

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Fri Jun 24 2022 15:52:31 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X-33 Y17 F6000 ; go to first probe point
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning