Best posts made by KevinMar

@diy-o-sphere Huh, yeah that ain't right

@fcwilt I'm currently re-running the autotuning with the removed T, B, and C values from the config

@fcwilt it included M307 commands that were generated from the autotuning and saved using M500

@fcwilt Affirmative

@fcwilt Yes, all 3 faulted (nearly) simultaneously, when heating is initiated simultaneously

@fcwilt "Print will be terminated if a heater fault is not reset within 10 minutes"

The thing that keeps confusing me is that this is a very standard-issue setup. Running all standard E3D + Duet hardware, and running a stable release of the firmware.

@fcwilt Yes, toolboards are at the addresses assigned

@phaedrux Ask and you shall receive

@fcwilt It's a printer with 4 tools, just so happened that the 4th tool continued heating to ~120C before faulting (different M307 parameters). All 4 tools have the issue

@fcwilt

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-9P63L-DJ3T8-6JKDD-3SD6M-9V4Z9
Used output buffers: 1 of 40 (16 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 63832 of which 12 recycled
Never used RAM 139444, free system stack 200 words
Tasks: SBC(ready,5.3%,298) HEAT(delaying,0.0%,325) Move(notifyWait,0.0%,302) CanReceiv(notifyWait,0.1%,799) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,7.4%,93) MAIN(running,87.0%,922) IDLE(ready,0.1%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:01:48 ago, cause: software
Last software reset at 2021-08-20 13:46, reason: User, none spinning, available RAM 139444, slot 1
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 134
MCU temperature: min 38.9, current 39.3, max 39.4
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 14442, writes 16 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 14442, writes 16 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 14443, writes 15 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 14447, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 14443, writes 15 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 14445, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-08-20 13:48:32
Slowest loop: 60.53ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.2
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 1033, received 5285, lost 0, longest wait 2ms for reply type 6049, peak Tx sync delay 7, free buffers 49 (min 48), ts 545/544/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
State: 4, failed transfers: 0, checksum errors: 0
Last transfer: 1ms ago
RX/TX seq numbers: 3860/3860
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c83c
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 35.84, max wait times: 5.8ms/0.0ms
Codes per second: 1.10
Maximum length of RX/TX data transfers: 6116/716