@Phaedrux

I cant send you the M122 because i am bloked from sending, they think its a spam.

@Phaedrux
Hi,
Thank to answer.
When i try to move more than 400mm i am at the end of my axis and i hit the rail, i am missing 200mm.
If i command 50mm the move is 75mm.

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Jan 28 2023 13:33:56 GMT-0500 (Eastern Standard Time)
G91 ; relative positioning
G1 H2 Z0 F6000 ; lift Z relative to current position
G1 H1 X-605 Y-605 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-605 Y-605 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-505 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z0 F100 ; lift Z relative to current position
;G90 ; absolute positioning

---

Hello,
This is the first time i try to configure a system like this and to be honest i have a lot of difficulty.
I have a Tronxy VEHO 600 printer, i installed a Duet 2 wifi on my printer.
My problem is that my printer is a 600x600x600mm but i am not able to go more than 400mm in each axis.
Can you help me please.
Thanks in advance.

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Jan 28 2023 13:33:56 GMT-0500 (Eastern Standard Time)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"TRONXY " ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E98.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z180.00 E1500.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X950 Y950 Z950 E950 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X600 Y600 Z500 S0 ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

; Z-Probe
M558 P0 H0 F0 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X50:550 Y50:550 S50 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 X501 R4700 ; configure PT1000 for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

@Phaedrux

Hi Phaedrux,

Thanks very much for your help, with your explanations i finally understood how to adjust the microstepping and evrerything works fine.
I will try to update the firmware as you told me.

@Phaedrux

I cant send you the M122 because i am bloked from sending, they think its a spam.

@Phaedrux
Hi,
Thank to answer.
When i try to move more than 400mm i am at the end of my axis and i hit the rail, i am missing 200mm.
If i command 50mm the move is 75mm.

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Jan 28 2023 13:33:56 GMT-0500 (Eastern Standard Time)
G91 ; relative positioning
G1 H2 Z0 F6000 ; lift Z relative to current position
G1 H1 X-605 Y-605 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-605 Y-605 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-505 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z0 F100 ; lift Z relative to current position
;G90 ; absolute positioning

---

Hello,
This is the first time i try to configure a system like this and to be honest i have a lot of difficulty.
I have a Tronxy VEHO 600 printer, i installed a Duet 2 wifi on my printer.
My problem is that my printer is a 600x600x600mm but i am not able to go more than 400mm in each axis.
Can you help me please.
Thanks in advance.

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Jan 28 2023 13:33:56 GMT-0500 (Eastern Standard Time)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"TRONXY " ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E98.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z180.00 E1500.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X950 Y950 Z950 E950 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X600 Y600 Z500 S0 ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

; Z-Probe
M558 P0 H0 F0 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X50:550 Y50:550 S50 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 X501 R4700 ; configure PT1000 for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined