That is too cool
@phaedrux said in Firmware wishlist and priorities for Duet WiFi and Duet Ethernet:
; Play a triumphant tune to celebrate a successful print.
M400 ; Clear queue before jingle
G4 S1
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S2500
G4 P251
M300 P150 S2000
G4 P151
M300 P150 S2500
G4 P151
M300 P350 S3700
G4 P351
M400
I am using Slic3r Prusa 1.39.1-prusa3d-win64.
Duet Wifi 1.21 Firmware 1.21 Server Version, 1.21 Web Interface
I am trying to print a muli-color butterfly with prime tower and hardware retraction.
No custom G-Code for tool change,start,stop,etc
If is use G-code flavor RepRap/Sprinter then I get a ton of
Error: M900 command is not supported
Error: M907 command is not supported
Other choice are not mutch better
Repetier (Can not use Wipe Tower), only supported for Marlin, RepRap/Sprinter)
Marlin (Can do all) Get the same M900 and M907 errors
Smoothie (Not tested)
No extrusion (Can not use hardware Retraction), only supported by Marlin, Smoothie, Repeiter, MachineKit)
and may more
Any idea on what G-code flavor I should use.
Or do I need to use another slicer
I printed most of my DBOT parts in PETG and some in PLA.
But After some time the PLA cracked and I reprinted them in PETG.
The DBOT has been running hard for over 1 year
My VOTE is for PETG
Yes, I Forgot to put that in the info. Cura 3.2.1 works fine also
@dc42
Yes, It is related to what slicer created the file
If sliced with Repetier Host Cura, shown in the Generated by Cura_SteamEngin 15.01.
The error happens when calculation Object Height/Layer Height/ and Filament Usage.
Onec calculation is done only Object Height that has any data, Layer Height/ and Filament Usage has n/a
All other slicers I tried worked just fine Slic3r 1.2.9, Slic3r 1.34.1-prusa3d-win64, Sl1c3r 1.37.1-prusa3d-win64
Something new in error in 1.21 that I did not see in 1.20
Browser or web problem. Error after uploading a file
JavaScript Error
A JavaScript error has occurred so the web interface has closed the connection to your board. It is recommended to reload the web interface now. If this happens again, please contact the author and share this error message:
Version: 1.21
Message: Uncaught TypeError: Cannot read property 'axesHomed' of undefined
URL: http://10.0.2.147/js/dwc.js
Line: 776:70
Error object: {}
I am getting
Request Timeout
The last HTTP request has timed out. Please make sure the connection between your device and the board is not interrupted.
Anytime I go into G-Code Files then into a Directory with lots of files. I get a spinney icon then
request Timeout
the files has a * infront of them.
Looks like when I go into a directory that I have not gone into after the patch
Some sort of processing is going on change the * to a page icon
Same problem when I upload a large gcode file
when I hit close after uploading
the file show a * and the the Request Timeout
I am trying to set up pause the print do I use something like @pause or M226?
and is there a way to send a message to paneldue with a beep or two?
Thanks
I would like also to sort by last print date or how many time the file has been printed.
One last thing I would like to see how long it took to print
Ok I think I have this figured out
I was trying the command by sending gcode through the web not in the config.g
Once I put the commands in config.g
On reboot I got 4 flashes and it looks like it is working.
I will be testing more tomorrow after I remount and rewire it back in place
This bring up a few question
1. on boot up does the sensor output become a input to read the config from the duetwifi in the first 4 seconds?
2. Is this only done at bootup or can this be triggered at any time?
3. Does the sensor use all 6 Z probe modes?
4. What does each flash mean 1,2,3,4,?
5. Is there a place I can read these details
Thanks
Found 1 problem my Z Probe IN Wire that was reading several M OHM's (Replaced)
The wire itself was the problem not the connector.
Thanks
Sensor Wiring
Out GND VCC
White Black Brown
Wire to Wire Connector
From
White Black Brown
To
White Black Red
To the Duet Wifi
Z Probe IN GND Z_Probe_MOD +3.3V
White Black Red
I have Mini differential IR sensor by dc42
FIrst Problem (Fixed)on power up is flashes 2 time not 4.
I move Z Probe In to Z Probe_Mod and set M558 P1
Got 4 flashes
Does not matter if Z probe or Z Probe_mod is wired
Now I
M558 P1 and G31 P500 Z1.0
and P2 and P3
It only shows 468 no matter what the height is Z
The Red Light goes on at the correct height
My Bed is a Black aluminum Heat bed with Glass on top, using glue stick on top of that
I have not updated to 116 Yet but I am on 115C
I do not know if this feature is already in the PanelDue.
But I would like for the PanelDue to read the Default Heater Temperatures and Default Bed and Chamber Temperatures setting.
That I configed through the Duet Wifi web site,
Do I can choose them for the Bed and hot-end temp
Thanks
I would also like to see a login and password.
For event like MRRF.