Posts made by jkdp

M566 X1250 Y1250 Z78 E310 ; Set maximum instantaneous speed changes (mm/min)
M203 X15000 Y15000 Z160 E9000 ; Set maximum speeds (mm/min)
M201 X210 Y210 Z100 E2755

basically low accceel and high jerk

200 jerk and 1050 accel got rid of the bulging corners for me

ok I played with my jerk and acceleration settings more and got not much of a visible difference, if anything. I downloaded and Installed the new firmware and am noticing a lot less difference at higher speeds than slower now just to fine tune it. Any advice ??

Toronto, Canada

haha, not much building the machine and testing, and calibrating it for resale purpose. Ive had a few request here in Toronto locally and have build a few small machines, But this has been a crazy 8 month battle from design to build. But looking good now... finally.... Larger machines are soo much harder to calibrate than smaller ones I've learnt, but think I've got the hang of it, besides this ringing...

NO in regards to the notes I will look at them, right now... and report bak, you guys are quick with the responses I really appreciate it....

On another note, I"ve started printing a low poly waitier hands. ANd am seeing a lot of ringing and cannot eliminate it no matter what I try. I did notice it on my t-rex from MakerBot which scaled and printed beautifully, but because there were many small curvatures the to form the skull ur not able to see them as clearly. But they are there, visibly. some pics of the ringing with the low poly waiter hands. any advice, I've played around with jerk and accelrations and speeds from 50mm/s-200mm/s. and cannot get rid of the ringing.

adjusting

a finished print, in case any one wanted to see it.

yes I do have the height map with g29 thanks again guys

ALSO one other thing now when I run g32 I get the leadscrew adjustment made but I am not able to see a heigh map from the gui.??

correction config.g

also one other question should I have

M92 X160 Y80 Z1605 E418 ; Set steps per mm

or should I have this

M92 X160 Y80 Z1605:1605:1605:1605 E418 ; Set steps per mm

with the same idea for all parameters with z axis movement settings with-in config.sys

I found the problem. Stupid user error... I've been battling with this past 3 months.....

M671 X:-150:-150:800:800 Y-10:850:850:-10 S1

I have a : in front of the x axis coordinate X:-150

Ugh...

But Thank you very much guys administrator and Phaedrux wouldn't have been able to figure this one out without you guys.

is the location of my m671 command in my config.g file in the correct location I do have it after the m669 and m667 but....

in the "settings" tab - under "Machine Properties" shouldn't all 4 z motors be listed there?

I think my error be in my mapping or in my lead screw position if someone can look over that.

SOME PROGRESS!! got this msg:

10‎:‎09‎:‎58‎ ‎PM
M671 Z leadscrew coordinates are not configured

basically I want the leadscrew adjustment to be made prior to printing

what I want to happen is lets just say new build. I want to run g28 home, all axes, then a g29 to prepare a heightmap and then run g32 before a print to sync my motors so they are perfectly plane. and then start a print.

when I run g32 the z motors are turning, when a [print starts it does compensate for bed surface. but What I want to know is why it does not level the motors prior to a print when I run g32, even if I run it numerous times it does not show me different parameters.

Yes I had s4 and still not getting any leadscrew adjustments only the "Bed equation fits points [0.0, 0.0, 0.026] [0.0, 720.0, -0.016] [650.0, 720.0, 0.155] [650.0, 0.0, 0.018]" parameter.

They've been turning out pretty good, a few settings left to adjust with the retraction settings and have a slight wobble in 2 screws, have 2 more coming in, just waiting to change them out.
thanks