Posts made by jaygrovr

@dc42 where is the documentation for this? I am actually trying to connect dotstars to the PI board that is running DWC. WHen I try to send a M150 I get an error "M150 does not support X and Q parameters in this mode. Refer to the DHC config instead.

yes, i was looking around, i cant find a single location where the theme colors are stored.

Jason

Does anyone know how I can customize colors for the dark theme?

Thank you so much for the info. Is there somewhere posted the instructions on how I could build my own version? I am actually just trying to remove some features. I know it sounds strange, but that is what I am trying to do.

thanks

Does anyone know what folder the DWC web files are stored? I am trying to make some changes to the html5 and vue. Thanks

Stuartofmt, thank you. So you get an image on both a local PI screen and another pc browsing in? What URL did you provide to the DWC configuration?

Yes, I did both of those things, but i cant get it to work on both the local pi screen and the web page on another pc, either local port or remote, it seems like it has to be one or another. there is an option in the motion setup "stream_localhost" has to be on for it to work locally on attached PI screen and has to be off to work on a remote web browser. How do i make it work on both at the same time? Also the update rate seems to be about 1hz or worse.

jason

Looks like it was found.

dmesg | grep -i usb
1: New USB device fo[    0.128801] usbcore: registered new interface driver usbfs
[    0.128857] usbcore: registered new interface driver hub
[    0.128982] usbcore: registered new device driver usb
[    1.191613] usbcore: registered new interface driver r8152
[    1.191677] usbcore: registered new interface driver lan78xx
[    1.191744] usbcore: registered new interface driver smsc95xx
[    1.192212] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    1.195748] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    1.195765] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.195780] usb usb1: Product: xHCI Host Controller
[    1.195794] usb usb1: Manufacturer: Linux 5.4.51-v7l+ xhci-hcd
[    1.195808] usb usb1: SerialNumber: 0000:01:00.0
[    1.196390] hub 1-0:1.0: USB hub found
[    1.197053] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    1.197075] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    1.197515] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[    1.197531] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.197546] usb usb2: Product: xHCI Host Controller
[    1.197560] usb usb2: Manufacturer: Linux 5.4.51-v7l+ xhci-hcd
[    1.197574] usb usb2: SerialNumber: 0000:01:00.0
[    1.198117] hub 2-0:1.0: USB hub found
[    1.200339] usbcore: registered new interface driver uas
[    1.200441] usbcore: registered new interface driver usb-storage
[    1.209395] usbcore: registered new interface driver usbhid
[    1.209406] usbhid: USB HID core driver
[    1.560558] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    1.743251] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    1.743268] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.743283] usb 1-1: Product: USB2.0 Hub
[    1.745310] hub 1-1:1.0: USB hub found
[    1.890814] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[    1.921749] usb 2-1: New USB device found, idVendor=2357, idProduct=0601, bcdDevice=30.00
[    1.921766] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    1.921781] usb 2-1: Product: USB 10/100/1000 LAN
[    1.921795] usb 2-1: Manufacturer: TP-LINK
[    1.921808] usb 2-1: SerialNumber: 000001000000
[    2.091325] usb 2-1: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[   59.510562] usb 1-1.3: new high-speed USB device number 3 using xhci_hcd
[   59.664628] usb 1-1.3: New USB device found, idVendor=32e4, idProduct=8830, bcdDevice= 1.00
[   59.664648] usb 1-1.3: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[   59.664665] usb 1-1.3: Product: HD USB Camera
[   59.664680] usb 1-1.3: Manufacturer: HD USB Camera
[   59.664694] usb 1-1.3: SerialNumber: 2020040501
[   59.729505] uvcvideo: Found UVC 1.00 device HD USB Camera (32e4:8830)
[   59.740595] input: HD USB Camera: HD USB Camera as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input1
[   59.741127] usbcore: registered new interface driver uvcvideo
[   59.741141] USB Video Class driver (1.1.1)
[110273.729856] usb 1-1.3: USB disconnect, device number 3
[110289.379592] usb 1-1.3: new high-speed USB device number 4 using xhci_hcd
[110289.532788] usb 1-1.3: New USB device found, idVendor=32e4, idProduct=8830, bcdDevice= 1.00
[110289.532797] usb 1-1.3: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[110289.532804] usb 1-1.3: Product: HD USB Camera
[110289.532810] usb 1-1.3: Manufacturer: HD USB Camera
[110289.532815] usb 1-1.3: SerialNumber: 2020040501
[110289.535595] uvcvideo: Found UVC 1.00 device HD USB Camera (32e4:8830)
[110289.544150] input: HD USB Camera: HD USB Camera as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input2
[289864.432365] usb 2-1: USB disconnect, device number 2
[289864.922629] usb 2-1: new SuperSpeed Gen 1 USB device number 3 using xhci_hcd
[289864.953396] usb 2-1: New USB device found, idVendor=2357, idProduct=0601, bcdDevice=30.00
[289864.953412] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[289864.953425] usb 2-1: Product: USB 10/100/1000 LAN
[289864.953438] usb 2-1: Manufacturer: TP-LINK
[289864.953450] usb 2-1: SerialNumber: 000001000000
[289865.113055] usb 2-1: reset SuperSpeed Gen 1 USB device number 3 using xhci_hcd
[289865.274136] usbcore: registered new interface driver cdc_ether
[344417.271957] usb 1-1.3: USB disconnect, device number 4
[344530.420204] usb 1-1.3: new high-speed USB device number 5 using xhci_hcd
[344530.583587] usb 1-1.3: New USB device found, idVendor=32e4, idProduct=8830, bcdDevice= 1.00
[344530.583606] usb 1-1.3: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[344530.583623] usb 1-1.3: Product: HD USB Camera
[344530.583638] usb 1-1.3: Manufacturer: HD USB Camera
[344530.583653] usb 1-1.3: SerialNumber: 2020040501
[344530.587243] uvcvideo: Found UVC 1.00 device HD USB Camera (32e4:8830)
[344530.606258] input: HD USB Camera: HD USB Camera as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input3

My dev folder has many video lines.. video0 through video16

So now I think my camera is actually video1. It seems happier on the log. How can I tell what the URL will be for the camera stream to work with DWC? I understand it has to be an image sequence. Do I need to set the url in the motion.conf properly for that? Can someone give me an example?

thanks again everyone

Jason

I only installed motion, not sure what else would be keeping it busy.

Also its not showing a name of the camera as a device, but I know its the 32e4: since it goes away when I unplug it

Bus 002 Device 002: ID 2357:0601 TP-Link
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 32e4:8830
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

I actually followed that guide and the camera is still not working. The log is complaining something about the camera input not correct as shown here.

cap.driver: "uvcvideo"
cap.card: "HD USB Camera: HD USB Camera"
cap.bus_info: "usb-0000:01:00.0-1.3"
cap.capabilities=0x84A00001
------------------------
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] v4l2_get_capability: - VIDEO_CAPTURE
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] v4l2_get_capability: - STREAMING
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] v4l2_select_input: name = "Camera 1", type 0x00000002, status 00000000
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] v4l2_select_input: - CAMERA
[1:ml1] [ERR] [VID] [Sep 29 17:21:30] v4l2_select_input: Error selecting input 0 VIDIOC_S_INPUT: Device or resource busy
[1:ml1] [ERR] [ALL] [Sep 29 17:21:30] mlp_capture: Video device fatal error - Closing video device
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] vid_close: Cleaning up V4L2 device
[1:ml1] [NTC] [VID] [Sep 29 17:21:30] v4l2_cleanup: Closing video device /dev/video0
[1:ml1] [NTC] [ALL] [Sep 29 17:21:37] mlp_actions: End of event 3

@T3P3Tony yes I tried motion, it seems that there is an issue with selecting the right input on the camera. Btw this camera works out of the box on octoprint. I will find a cut sheet and attach when I get a minute.

Does anyone know how to get an 8mp ELP usb camera to work on duet or DWC running on a pi? Thanks

Hi guys, is it possible for me to update how the webpages look, and I am not talking about just the colorscheme. What tools were used to generate the html5 and ajax for this? Is there original files that can be used to edit the layouts?

Thanks

Jason