Close to a year ago I acquired the complete but not working Wanhao Duplicator i3 and subsequently got the Duet 3 Mini 5+ board for it. None of my LCDs would work due to being ST7920 based.
The project gathered dust up until very recently when I decided to get an RPi and run Klipper. A few hiccups along the way but nothing too serious but I do find the 2 Z-axis screws to get out of sync very easily. I got a MicroProbe V2 for more consistent Z-homing but also to allow for auto gantry leveling.
Thanks for the help...I actually got it working now. This time I only commented the M558 line out
@jay_s_uk
It's plugged into the zstop port.
I thought that the M574 would take care of it
Yes, every time. I tried a normal closed switch now then it shows Z is stopped.
However it still seems to think there is a Z probe as well which is stopped.
How to I get rid of the Z probe altogether?
@fcwilt I took out the lines
; Z-Probe
M558 P8 H0 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X25:185 Y25:185 S30 ; define mesh grid
Still the same M119 result.
What am I missing? I am totally new to RepRap as I have been using Marlin for the past 7 years
@fcwilt No I only have a switch.
and M119 gives me this:
M119 Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: at min stop
Do I actually just have to remove the Z-0Probe "section"
Hi all. I have searched and searched, and unless I am not searching right or missing the right posts I can't find the solution to my specific problem.
I actually have a Fly RRF E3 board but using some the Duet firmware and so on. I followed Teaching Tech's Youtube video and it helped me get past other issues I had at first, as the video explains putting this board on a Prusa (I have a clone) and not an Ender 3.
The Z endstop switch is a plain normally open switch.
I have tried both
M558 P1 H0 F120 T6000
and
M558 P3 H0 F120 T6000
X and Y homes perfectly, Z does move up and down when I move it manually. But Z only lifts when I try to home it. It does not even try to home.
Any help will be highly appreciated as I am getting very frustrated with this board after coming from Marlin
Here is my config.g:
; Configuration file for Fly-E3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.1-LPC-STM32+7 on Wed Apr 20 2022 19:17:47 GMT+0200 (South Africa Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"MK3RRF" ; set printer name
; Network
M551 P"5423" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards using default driver timings
M569 P1 S1 ; physical drive 1 goes forwards using default driver timings
M569 P2 S1 ; physical drive 2 goes forwards using default driver timings
M569 P3 S1 ; physical drive 3 goes forwards using default driver timings
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z400.00 E160.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E1300 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X210 Y210 Z150 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop
; Z-Probe
M558 P3 H0 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X25:185 Y25:185 S30 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bed" T0 ; create bed heater output on bed and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; set temperature limit for heater 1 to 300C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H0 T45 ; set fan 0 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M918 P1 E4 F1000000 ; 12864 LCD screen