Duet 3 mini 5+ out 1&2 conectors. What is the size of these new connectors, both cable capacity mm2 pls.
and what crimp tool to use for them?
Posts made by j3dk
-
Duet 3 mini 5+ out 1&2 conectors
-
RE: Duet 3 mini 5+ network problems
@oliof Yes ,you are right, I just had this thought last night....
-
RE: Duet 3 mini 5+ network problems
@dc42 Yes and now it's online again I don't know what and why but now I have found it on a totally different IP that not existed yesterday.
Thanks a lot for your help and fast respond time.Jens Kej
-
RE: Duet 3 mini 5+ network problems
@jay_s_uk Yes, but I still can't find it on the given IP from YAT
-
RE: Duet 3 mini 5+ network problems
@jay_s_uk Yes and I get hte following result:
M552 S1
ok
WiFi module is connected to access point SecureNest, IP address 192.168.87.110
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3 (2021-06-15 21:46:11) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: RAKRW-A196U-D65J0-40KMW-LU03Z-7FDQQ
Used output buffers: 1 of 40 (2 max)
=== RTOS ===
Static ram: 102724
Dynamic ram: 105696 of which 60 recycled
Never used RAM 35224, free system stack 168 words
Tasks: NETWORK(ready,15.0%,385) HEAT(notifyWait,0.0%,366) Move(notifyWait,0.1%,334) CanReceiv(notifyWait,0.0%,941) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,340) TMC(notifyWait,0.0%,124) MAIN(running,84.0%,426) IDLE(ready,0.1%,29) AIN(delaying,0.8%,273), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:05:29 ago, cause: reset button
Last software reset at 2021-09-28 16:31, reason: User, GCodes spinning, available RAM 35224, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 329682, completed 329681, timed out 0, errs 0
Step timer max interval 737
MCU temperature: min 28.2, current 29.7, max 29.7
Supply voltage: min 0.5, current 0.6, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 63954, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 1: position 63954, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 2: position 63954, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 6: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 632817408
Slowest loop: 4.95ms; fastest: 0.11ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 2965, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17), ts 1648/0/0
Tx timeouts 0,0,1647,0,0,1316 last cancelled message type 4514 dest 127=== Network ===
Slowest loop: 20.99ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address f0:08:d1:02:eb:6b
WiFi Vcc 3.39, reset reason Power up
WiFi flash size 2097152, free heap 25464
WiFi IP address 192.168.87.110
WiFi signal strength -55dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
ok
- WiFi -
-
Duet 3 mini 5+ network problems
Why is my printer suddenly disapeared from my LAN? One night I turned it off and the next day when I turned it on it was disapeared from the IP-adress it had the day before and the control led for the web server was on.
I scanned my LAN but could not find it. Now I have tried everything described in the documentation, several times. The only thing that happens is the web server led turns om but can't connect to it from the IP, YAT says it have. When I try to connect to it I can't thoug the control Led was on and when I scan my LAN, I get this message
what is going on? -
RE: how to configure magnetic filament sensor on duet 3 mini 5+
@droftarts Hi there thank you for the advise. now I have figured it out putting this line in my config.g it works
M591 D0.3 P3 C"^io5.in" S1 ; filament monitor connected to E0_stop -
how to configure magnetic filament sensor on duet 3 mini 5+
I have conected my rotating magnet sensor to IO_5 on Duet3 mini 5+ but I can't find out how to set up my config.g
; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.2 on Thu Sep 16 2021 12:55:16 GMT+0200 (Centraleuropæisk sommertid); General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"JK Preddy mod" ; set printer name
M665 R261 L440 B185 H420 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S0 ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E415.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 Z0 S1 ; set minimum Z; Endstops
M574 X2 S1 P"^io1.in" ; configure active-high endstop for high end on X via pin ^io1.in
M574 Y2 S1 P"^io2.in" ; configure active-high endstop for high end on Y via pin ^io2.in
M574 Z2 S1 P"^io3.in" ; configure active-high endstop for high end on Z via pin ^io3.in; Z-Probe
M558 P5 R0.4 C"temp2+io4.out" H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds
M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 R180 S20 ; define mesh grid; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out5" Q500 ; create fan 2 on pin out5 and set its frequency
M106 P2 S0.25 H-1 ; set fan 2 value. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings
M591 P3 C"e0_stop" S1 ; filament monitor connected to E0_stop; Miscellaneous
T0 ; select first toolwhat am I missing?
-
RE: Dual Z-axis endstops
Thanks now Z and U is homing. Back to work…...
-
RE: Dual Z-axis endstops
I have the following software information:
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later + DueX5
Firmware Version: 1.21 (2018-03-21)
WiFi Server Version: 1.21
Web Interface Version: 1.21-RC4 -
RE: Dual Z-axis endstops
all should now be updated and I have read the release notes.
I'm homing X and Y fine but trying to home Z, my homez.g looks like this:
G91 ; relative positioning
M584 Z2 U3 P3
G1 S1 Z-355 U-355
G92 Z0.1
M584 Z2:3 P3
G90 ; absolute positioningbut only the spindle connected to the Z connector is trying to home but noting happens on U spindle. My machine properties looks like this:
Logical Drive Endstop hit Minimum Maximum InstantDv Max Speed Acceleration Motor Current
X Yes 0 mm 300 mm 15 mm/s 100 mm/s 500 mm/s² 800 mA
Y Yes 0 mm 300 mm 15 mm/s 100 mm/s 500 mm/s² 800 mA
Z No 0 mm 350 mm 1 mm/s 30 mm/s 250 mm/s² 800 mA
E0 No n/a n/a 1 mm/s 30 mm/s 250 mm/s² 800 mA
E1 Yes n/a n/a 2 mm/s 20 mm/s 250 mm/s² 800 mA
E2 Yes n/a n/a 2 mm/s 20 mm/s 250 mm/s² 800 mA
I can now see that endstop for Z works, the one I have set for U now works on E0 and my E3 no longer exists.
My parameters set for the U seems to be in E0 row but no min and max values are available here. I guess that's why my U axis can't move. What can I do to solve this? -
RE: Dual Z-axis endstops
1. Now I have updated my Firmware to ver. 1.21 and now all my declared endstops works, but still no readings of minimum and maximum for drive 3 aka U axis.
2. I use standard Makerbot Mechanical endstops ver. 1.2
3. M574 returns: Endstop configuration: X: low end active low switch, Y: low end active low switch, Z: low end active low switch, U: low end active low switch,
Now when I try to move Z up and down I get a red popup like this:
M120
G91
G1 Z-1 F6000
M121
Error: G0/G1: insufficient axes homed
Error: Pop(): stack underflow!homez still don't work
What's next? -
RE: Dual Z-axis endstops
Can you see the U endstop working in the Duet Web Control Machine Properties page? The LED is not always a reliable indication.
Found out that U endstop is not working and it seems like it is a problem related to my Duet WiFi board as I have tested/measured all wires, connectors and endstops, yhey are all ok.
Then I have tried to move the plug from my working Z stop to the U connector on the board but when I turn it on again and go to Machine Properties page nothing works.
Now I also have tried to move the stepper and endstop for my U axis to E4 on my duex5 and remap U in my confiig.g and homez.g but I still had the same problem.
Have tested all my endstops and they work properly on the XYZ axis. On all other they seem to work the oposite way in the machine properties page. Reported as hit and change from Yes to No when I hit them manually, Whats wrong then? -
RE: Dual Z-axis endstops
Your two M208 commands need to be moved to be after the M584 command, and you need to add U axis values to them.
I made something very wrong, messed it all up and had to put new configuration files on the SD-Card. Then I started all over again from scratch. Now my config.g and homez.g looks like this, much better structured, without unused comands etc. but the problem still remains the same:
–----------------------------------------------------------------------------------------------------------------------------------------
; config.g Dual Z-axis
; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Mar 19 2018 17:18:48 GMT+0100 (Rom, normaltid)
; Edited by J. Kej on Mon Mar 19 2018 20:58:48 GMT+0100 (Rom, normaltid); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 PJK'S FT-5 DD ; Set machine name
M552 S1 ; Enable network
M587 S"farce95taske53lufe" P"be81b0f702d6d23152c28d870e" ; Configure access point.
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes backwards
M569 P4 S1 ; Drive 4 goes forwards
M569 P5 S1 ; Drive 5 goes forwards
M569 P6 S1 ; Drive 6 goes forwards
M584 X0 Y1 Z2:3 U3 E4:5:6 P3 ; Configure drive remapping to dual Z-axis
M350 X16 Y16 Z16 U16 E16:16:16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z400 U400 E100100 ; Set steps per mm
M566 X900 Y900 Z12 U12 E120:120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1800 U1800 E1200:1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 U250 E250:250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 U800 E800:800:800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 U1 S1 ; Set axis minima
M208 X300 Y300 Z350 U350 S0 ; Set axis maxima; Endstops
M574 X1 Y1 Z1 U1 S0 ; Set active low endstops; Z-Probe
M558 P0 H3 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:285 Y15:285 S20 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X151 ; Configure thermocouple for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0.1 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H1 ; Define tool 1
G10 P1 X0 Y0 Z0.1 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
M563 P2 D2 H1 ; Define tool 2
G10 P2 X0 Y0 Z0.1 ; Set tool 2 axis offsets
G10 P2 R0 S0 ; Set initial tool 2 active and standby temperatures to 0C
M563 P3 D0:1:2 H1 ; Define tool 3
G10 P3 X0 Y0 Z0.1 ; Set tool 3 axis offsets
G10 P3 R0 S0 ; Set initial tool 3 active and standby temperatures to 0C
M568 P3 S1 ; Enable mixing for tool 3
M567 P3 E0.33:0.33:0.34 ; Set mixing ratios for tool 3; Automatic saving after power loss is not enabled
; Custom settings
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configured for Dual Z-axis by J. Kej on Mon Mar 19 2018 20:18:47 GMT+0100 (Rom, normaltid)
;
M584 Z2 U3 P3
G1 S1 Z-355 U-355
G92 Z0.1
M584 Z2:3 P3Endstop Z and U are working properly, led's on board lights up when i hit them with my finger. That's not the issue…...
-
RE: Dual Z-axis endstops
Your two M208 commands need to be moved to be after the M584 command, and you need to add U axis values to them.
I made something very wrong, messed it all up and had to put new configuration files on the SD-Card. Then I started all over again from scratch. Now my config.g and homez.g looks like this, much better structured, without unused comands etc. but the problem still remains the same:
–----------------------------------------------------------------------------------------------------------------------------------------
; config.g Dual Z-axis
; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Mar 19 2018 17:18:48 GMT+0100 (Rom, normaltid)
; Edited by J. Kej on Mon Mar 19 2018 20:58:48 GMT+0100 (Rom, normaltid); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 PJK'S FT-5 DD ; Set machine name
M552 S1 ; Enable network
M587 S"farce95taske53lufe" P"be81b0f702d6d23152c28d870e" ; Configure access point.
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S1 ; Enable Telnet; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes backwards
M569 P4 S1 ; Drive 4 goes forwards
M569 P5 S1 ; Drive 5 goes forwards
M569 P6 S1 ; Drive 6 goes forwards
M584 X0 Y1 Z2:3 U3 E4:5:6 P3 ; Configure drive remapping to dual Z-axis
M350 X16 Y16 Z16 U16 E16:16:16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z400 U400 E100100 ; Set steps per mm
M566 X900 Y900 Z12 U12 E120:120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1800 U1800 E1200:1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 U250 E250:250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 U800 E800:800:800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 U1 S1 ; Set axis minima
M208 X300 Y300 Z350 U350 S0 ; Set axis maxima; Endstops
M574 X1 Y1 Z1 U1 S0 ; Set active low endstops; Z-Probe
M558 P0 H3 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:285 Y15:285 S20 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X151 ; Configure thermocouple for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0.1 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H1 ; Define tool 1
G10 P1 X0 Y0 Z0.1 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
M563 P2 D2 H1 ; Define tool 2
G10 P2 X0 Y0 Z0.1 ; Set tool 2 axis offsets
G10 P2 R0 S0 ; Set initial tool 2 active and standby temperatures to 0C
M563 P3 D0:1:2 H1 ; Define tool 3
G10 P3 X0 Y0 Z0.1 ; Set tool 3 axis offsets
G10 P3 R0 S0 ; Set initial tool 3 active and standby temperatures to 0C
M568 P3 S1 ; Enable mixing for tool 3
M567 P3 E0.33:0.33:0.34 ; Set mixing ratios for tool 3; Automatic saving after power loss is not enabled
; Custom settings
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configured for Dual Z-axis by J. Kej on Mon Mar 19 2018 20:18:47 GMT+0100 (Rom, normaltid)
;
M584 Z2 U3 P3
G1 S1 Z-355 U-355
G92 Z0.1
M584 Z2:3 P3 -
RE: Dual Z-axis endstops
I have have an FT-5 and want to split my Z axis when homing, my Home Z.g looks like this:
; homez.g
; called to home the Z axis
;
; generated by Jens Kej on Sun Mar 11 2018 15.00G91 ; relative mode
G1 Z4 F200 ; raise head 4mm to ensure it is above the switch trigger height
G90 ; back to absolute mode
G1 X-305 Y-305 F1800 S1; move XY home
G1 X150 Y150 F2000 ; put the head to be centered when you home Z
G91 ; relative mode
M584 Z2 U3 ; split Z axis in two
G1 Z-400 U-400 S1 F100 ; home the Z- and U axis
G92 Z0.1 ; tell the software that it 0,1 mm above bed
G90 ; back to absolute mode
M584 Z2:3 ; make One Z axis againthe bed is moving fine up and down from web interface but only the Z axis is trying move when I push home Z, why?
here comes my config.g:
; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by Jens Kej on Thu Sep 21 2017 17:16:32 GMT+0200 (Rom, sommertid); General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z350 S0 ; Set axis maxima; Endstops
;M574 Z1 S1 ; Define Hall sensor active high on Z-axis
M574 X1 Y1 Z1 U1 S0 ; Define active low and unused microswitches
:M558 P1 X0 Y0 Z0 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
;G31 P600 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
;M557 X15:285 Y15:285 S20 ; Define mesh grid; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes backwards
M569 P4 S1 ; Drive 4 goes forwards
M569 P5 S1 ; Drive 5 goes forwards
M569 P6 S1 ; Drive 6 goes forwardsM584 X0 Y1 Z2:3 U3 E4:5:6 P3; Apply custom drive mapping
M350 X16 Y16 Z16 U16 E16:16:16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z400 U400 E100100 ; Set steps per mm
M566 X900 Y900 Z12 U12 E120:120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1000 U1000 E1200:1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 U250 E250:250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 U800 E800:800:800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
;M305 P1 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M305 P1 x151 ; Thermocouple
M307 H1 A626.6 C265.6 D13.9 ; hotend pid settings; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H1 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
M563 P2 D2 H1 ; Define tool 2
G10 P2 X0 Y0 Z0 ; Set tool 2 axis offsets
G10 P2 R0 S0 ; Set initial tool 2 active and standby temperatures to 0C; Network
M550 PFT-5 DD ; Set machine name
M552 S1 ; Enable network
M587 Sfarce95taske53lufffe P"be81b0f702d6d23152c28d870e" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Fans
M106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Custom settings are not configured
M501 ;Load overide config.g -
RE: Dual Z-axis endstops
I have have an FT-5 and want to split my Z axis when homing, my Home Z.g looks like this:
; homez.g
; called to home the Z axis
;
; generated by Jens Kej on Sun Mar 11 2018 15.00G91 ; relative mode
G1 Z4 F200 ; raise head 4mm to ensure it is above the switch trigger height
G90 ; back to absolute mode
G1 X-305 Y-305 F1800 S1; move XY home
G1 X150 Y150 F2000 ; put the head to be centered when you home Z
G91 ; relative mode
M584 Z2 U3 ; split Z axis in two
G1 Z-400 U-400 S1 F100 ; home the Z- and U axis
G92 Z0.1 ; tell the software that it 0,1 mm above bed
G90 ; back to absolute mode
M584 Z2:3 ; make One Z axis againthe bed is moving fine up and down from web interface but only the Z axis is trying move when I push home Z, why?
-
RE: Z-homing trouble
Now my homez.g look like this and it still dont't work???
; homez.g
; called to home the Z axis
;
; generated by Jens Kej on Mon Sep 25 2017 13.18G91 ; relative mode
G1 Z4 F200 ; raise head 4mm to ensure it is above the switch trigger height
G90 ; back to absolute mode
G1 X0 Y0 F2000 ; put the head wherever you want it to be when you home Z (omit this line if it doesn't matter)
G91 ; relative mode
G1 Z-200 S1 F100 ; move Z down until the switch triggers
G90 ; back to absolute mode
G92 Z0.1 ; tell the firmware that we are at Z=0.1mm -
Z-homing trouble
Mystery z-endstop trouble.
I have a Folgertech FT-5 with a Duet WiFi, Duex5 and a 3 color Diamond hotend. All endstop are the original Ultimaker like and they are all connected the same way.
Their led and the led”s on the Duet light when hit. I have no probe and they work on x and y axis but not on z axis, why???
Here is my config.g and homez.g:; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Sep 21 2017 17:16:32 GMT+0200 (Rom, sommertid); General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z350 S0 ; Set axis maxima; Endstops
M574 X1 Y1 Z1 S0 ; Define active low and unused microswitches
M558 P1 X0 Y0 Z0 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
;G31 P600 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
;M557 X15:285 Y15:285 S20 ; Define mesh grid; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M569 P5 S1 ; Drive 5 goes forwards
M584 X0 Y1 Z2 E4:5:6 ; Apply custom drive mapping
M350 X16 Y16 Z16 E16:16:16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z400 E420:420:420 ; Set steps per mm
M566 X900 Y900 Z12 E120:120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200:1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250:250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800:800:800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 1; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H1 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
M563 P2 D2 H1 ; Define tool 2
G10 P2 X0 Y0 Z0 ; Set tool 2 axis offsets
G10 P2 R0 S0 ; Set initial tool 2 active and standby temperatures to 0C; Network
M550 PFT-5 DD ; Set machine name
M552 S1 ; Enable network
M587 Sfarce95taske53lufffe P"be81b0f702d6d23152c28d870e" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Fans
M106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Custom settings are not configured
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool on Thu Sep 21 2017 17:16:32 GMT+0200 (Rom, sommertid); Lift Z relatively to current position
G91
G1 Z5 F6000; Back to absolute positioning
G90; Go to first bed probe point and home the Z axis
G1 X15 Y15 F6000; Uncomment the following lines to lift Z after probing
G91
G1 Z5 F100
G90
G92 Z0.1What the f*#@ is going on?
Any way thank you for a wonderful product and friendly support.