@droftarts Thank you for your opinion.
I tried to that and the machine did no longer crashes.
I changed the Emergyency stop configuration to external trigger.
As a result, the external trigger was triggered while homey.g was runnning.
So, Maybe the emergyency stop button and something are interfering.
I'm going to search the causing.
Thank you droftarts!
Here I show config.g, homeall.g, homey.g, and consol.
Comment out may be wrong( because these are developping)
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; Settings for E-moc X5
; generated by HRMK
; General preferences
G90 ; send absolute coordinates...
M550 P"E-moc X5 v2" ; set printer name
; Network
M552 P192.168.0.56 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0.0 S1 ; physical drive 0.0 goes backs
M569 P0.1 S1 ; physical drive 0.1 goes backs
M569 P0.2 S1 ; physical drive 0.2 goes backs
M569 P0.3 S0 ; physical drive 0.3 goes forwards
M569 P0.4 S0 ; physical drive 0.4 goes forwards
M569 P0.5 S0 ; physical drive 0.5 goes forwards
M584 X0.0 Y0.1:0.2 Z0.3 A0.4 C0.5 ; set drive mapping
M350 X8 Y8 Z8 A8 C8 I1 ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z200.00 A223.4567 C222.222222222222 ; set steps per mm
M566 X60.00 Y60.00 Z60.00 A60.00 C200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X7000.00 Y7000.00 Z7000.00 A2000.00 C3000.00 ; set maximum speeds (mm/min)
M201 X400.00 Y400.00 Z400.00 A100.00 C400.00 ; set accelerations (mm/s^2)
M906 X2400 Y2400 Z2400 A2900 C2400 I100 ; set motor currents (mA)
M915 P0.0 S3 F0 R0
M915 P0.1:0.2 S3 F0 H240 R0
M915 P0.3 S3 F0 R0
M564 S1 H0 ; Disable jog commands when not homed
; Axis Limits
M208 X-327 Y-295 Z-295 A-95 C-99999. S1 ; set axis minima
M208 X0 Y0 Z0 A140 C99999. S0 ; set axis maxima
; Endstops
M574 X1 S3
M574 Y1 S4
M574 Z1 S3 ; configure active-high endstop for low end on Z via pin io3.in
M574 A1 S1 P"io4.in" ; configure active-high endstop for low end on A via pin io4.in
M574 C1 0 P"io5.in" ; configure active-high endstop for low end on C via pin io5.in
;Emergency stop
M950 J1 C"^io6.in" ; configure active-high endstop for Emergency stop via pin io6.in
M581 P1 T0 S1 R0
;Touch probe
M558 P5 C"!io7.in" F1200:400 T6000 H-1 ; configure active-high endstop for Touch probe via pin io7.in
; Tools
; Custom settings are not defined
M453
M501 ; Load config_override
; homeall.g
; called to home all axes
;
; generated for E-moc X5 by HRMK
G91 ; relative positioning
M201.1 Z150
M400
M913 Z45
M400
G1 H1 Z500. F2000 ; move quickly to Z axis endstop and stop there (first pass)
M400
M913 Z100
M400
G1 H2 Z-5. F6000 ; go back a few mm
M400
M913 Z45
M400
G1 H1 Z200.F2000 ; move slowly to Z axis endstop once more (second pass)
M400
M913 Z100
M400
M201.1 Y150 Z400
M400
M913 Y45
M400
G1 H1 Y300 F2000
M400
M913 Y100
M400
G1 H2 Y-5 F4000 ; go back a few mm
M400
M913 Y45
M400
G1 H1 Y300 F2000
M400
M913 Y100
M400
G1 H2 Y-5 F4000 ; go back a few mm
M400
M913 Y45
M400
G1 H1 Y20 F2000 ; move slowly to Y axis endstop once more (second pass)
M400
M913 Y100
M400
M201.1 Y400
M400
M913 Y100
M400
M201.1 X150
M400
M913 X20
M400
G1 H1 X350 F2000 ; move quickly to X axis endstop and stop there (first pass)
M400
M913 X100
M400
G1 H2 X-5 F4000 ; go back a few mm
M400
M913 X20
M400
G1 H1 X10 F2000 ; move slowly to X axis endstop once more (second pass)
M400
M913 X100
M400
G1 H2 X-16 F4000 ; go back a few mm
M201.1 X400
M400
M913 X100
M400
G1 H1 A-200 F1000 ; move quickly to A axis endstop and stop there (first pass)
G1 H2 A5 F1000 ; go back a few deg
G1 H1 A-200 F800 ; move slowly to A axis endstop once more (second pass)
G1 H2 A5 F1000 ; go back a few deg
G1 H1 C-360 F1800 ; move quickly to C axis endstop and stop there (first pass)
G1 H2 C5 F1800 ; go back a few deg
G1 H1 C-200 F500 ; move slowly to C axis endstop once more (second pass)
G1 H2 C3 ; go back a few deg
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum
G92 X0 ; set X position to axis minimum
G92 Y0 ; set Y position to axis minimum
G92 A-85 ; set A position to axis minimum
G92 C0 ; set C position to axis minimum
G90G0A0 ; go back to A0
M400
M913 X100 Y100
M400
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F40 ; lift Z relative to current position
;G90 ; absolute positioning
; homey.g
; called to home the Y axis
;
; generated for E-moc X5 by HRMK
G91 ; relative positioning
;G1 H2 Y-20 F4000
M201.1 Y150
M400
M913 Y45
M400
G1 H1 Y300 F2000
M400
M913 Y100
M400
G1 H2 Y-5 F4000 ; go back a few mm
M400
M913 Y45
M400
G1 H1 Y300 F2000
M400
M913 Y100
M400
G1 H2 Y-5 F4000 ; go back a few mm
M400
M913 Y45
M400
G1 H1 Y20 F2000 ; move slowly to Y axis endstop once more (second pass)
M400
M913 Y100
M400
G92 Y0 ; set Maschine position Y-5
G90 ; absolute positioning
M201.1 Y400
M400
M913 Y100
M400
homey.g and M122
2024/10/17 20:34:06
m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.2 (2024-06-11 17:13:58) running on Duet 3 MB6HC v1.02 or later (standalone mode)
Board ID: 0JD4M-958L1-M24TD-6JKDD-3S46K-91TPX
Used output buffers: 3 of 40 (19 max)
Error in macro line 4 while starting up: Heater 0 not found
=== RTOS ===
Static ram: 155360
Dynamic ram: 120296 of which 0 recycled
Never used RAM 67408, free system stack 152 words
Tasks: NETWORK(1,ready,40.8%,182) ETHERNET(5,nWait 7,0.1%,316) HEAT(3,suspended,0.0%,355) TMC(4,nWait 6,9.2%,53) MAIN(1,running,49.6%,444) IDLE(0,ready,0.3%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:40 ago, cause: software
Last software reset at 2024-10-17 20:33, reason: User, Gcodes spinning, available RAM 67408, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 40.8, current 41.2, max 41.4
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/32/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 432, reads 24730, writes 15 timeouts 0
Driver 1: standstill, SG min 0, mspos 720, reads 24701, writes 44 timeouts 0
Driver 2: standstill, SG min 0, mspos 176, reads 24702, writes 44 timeouts 0
Driver 3: standstill, SG min n/a, mspos 592, reads 24731, writes 15 timeouts 0
Driver 4: standstill, SG min n/a, mspos 16, reads 24732, writes 14 timeouts 0
Driver 5: standstill, SG min n/a, mspos 528, reads 24732, writes 14 timeouts 0
Date/time: 2024-10-17 20:34:05
Slowest loop: 9.66ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 3, maxWait 13221ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 11, completed 11, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Disabled
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 98/0/0
Tx timeouts 0,0,97,0,0,0 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 6.93ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== WiFi ===
Interface state: disabled
Module is disabled
Failed messages: pending 0, notrdy 0, noresp 0
Socket states: 0 0 0 0 0 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
2024/10/17 20:33:45
G28 Y
Emergency Stop! Reset the controller to continue.
2024/10/17 20:33:45
緊急停止、再接続を試みます...
homeall.g
2024/10/17 21:03:42
Emergency Stop! Reset the controller to continue.
Error: G91: Machine is halted
Error: M201.1: Machine is halted
Error: M400: Machine is halted
Error: M913: Machine is halted
Error: M400: Machine is halted
Error: G1: Machine is halted
Error: M400: Machine is halted
Error: M913: Machine is halted
Error: M400: Machine is halted
Error: G1: Machine is halted
Error: M400: Machine is halted
Error: M913: Machine is halted
Error: M400: Machine is halted
Error: G1: Machine is halted
Error: M400: Machine is halted
Error: M913: Machine is halted
Error: M400: Machine is halted
Error: G1: Machine is halted
Error: M201.1: Machine is halted
Error: G92: Machine is halted
Error: G90: Machine is halted
Error: Failed to home axes XAC
2024/10/17 21:03:41
緊急停止、再接続を試みます...
Hi everyone!
This is my first post at here.
Now,I'm developing open source 5-axis CNC milling machine.
https://github.com/ryotakito/E-mocX5
I applied sensorless homing at linear axis (X,Y,Z-axis) of this machine.
But,homing of only Y-axis often failed.
(X and Z-axis have no problem.)
Details
Machine will stop and console show me "G28 (Y) Emergency Stop! Reset the controller to continue." when Y-axis carrier hit at home position.
And,duet3 will no longer accept operations,but I can load and overwrite gcodes like config.g and homeall.g e.t.c.
STATUS LED stays on at maximum brightness.
I thought it is caused by overcurrent at first.
But, it sometimes occur at low current and sometimes don't occur at a little higher current.
And, it occured every time at same parameter.
Then, I checked consol and log using M122.But actual crashed time of Duet3 and Last reset time are not match.
So,I think there is another reason why that occur.
I want you to tell me what cause that.
Thank you for reading my poor english.