Posts made by Handymanpa54

@cjm
I trimmed the code and have one instance of M563. Still no luck. Maybe it's easier to get an output on Fan0 output?
I'm wondering if I can get an output off of the fan connectors or E0 Heater connector? Using the expansion connector is not so easy.

My config.g

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jul 30 2021 11:14:49 GMT-0400 (Eastern Daylight Time)

; General preferences

G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"CNC 6040"                                   ; set printer name

; Network
M552 P192.168.1.14 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.2                                  ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X640.00 Y640.00 Z640.00 E420.00                ; set steps per mm
M566 X400.00 Y400.00 Z80.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X2500.00 Y2500.00 Z240.00 E1200.00            ; set maximum speeds (mm/min)
M201 X300.00 Y300.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E500 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X390 Y590 Z68 S0                              ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop"                               ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop"                               ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z1 S1 P"^zstop"                               ; configure active-high endstop for low end on Z via pin ^zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid


M950 R0 C"^fan0" Q2000 L0:24000   					; Create spindle index 0, PWM frequency 2KHz, 
                                                  ; Lmin:max rpm ranges from 0rpm at PWM=0% to 24000rpm at 100% PWM
                                                  ; spindle speed PWM pin	: exp.13 
M563 P0 R0 S"Spindle"                             ; Create Tool 0 with Spindle 0 and call it Spindle

T0						  							; Select Tool 0 (or make sure generated by CAM)

 



M453												; CNC Mode
; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
;M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
;M140 H0                                            ; map heated bed to heater 0
;M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
;M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
;M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
;M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
;M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
;M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
;M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
                       ; define tool 0
;M453 S0 C"out1" R24000 Q100 T0
M563 S"XYZ-Probe" P1                    ; define XYZ Touch Probe tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                  ; enable support for PanelDue
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                                                 ; select first tool

Hello All,
I have a Duet2 ethernet and trying to get this CNC running. I tried sending M3 P0 S2000 but nothing. I took a look with my Oscope to see if any PWM is coming on Pin 13 signal, pin 30 gnd of expansion connector.
I think I have the Gcode right but I really don't fully understand These commands yet.

code_text
8/9/2021, 7:11:15 PM 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6JTD2-3S46K-KU0LM
Used output buffers: 1 of 24 (13 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 70264 of which 0 recycled
Never used RAM 20276, free system stack 150 words
Tasks: NETWORK(ready,25.2%,237) HEAT(delaying,0.0%,390) Move(notifyWait,0.1%,309) MAIN(running,74.6%,449) IDLE(ready,0.2%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:08:25 ago, cause: power up
Last software reset at 2021-08-09 18:46, reason: User, GCodes spinning, available RAM 20276, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 28.9, current 39.7, max 40.2
Supply voltage: min 23.8, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max 0/1023
Driver 1: position 0, standstill, SG min/max 0/1023
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-08-09 19:11:12
Cache data hit count 4294967295
Slowest loop: 9.14ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 490658ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 14.94ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jul 30 2021 11:14:49 GMT-0400 (Eastern Daylight Time)

; General preferences

G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"CNC 6040"                                   ; set printer name

; Network
M552 P192.168.1.14 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.2                                  ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X640.00 Y640.00 Z640.00 E420.00                ; set steps per mm
M566 X400.00 Y400.00 Z80.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X2500.00 Y2500.00 Z240.00 E1200.00            ; set maximum speeds (mm/min)
M201 X300.00 Y300.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E500 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X390 Y590 Z68 S0                              ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop"                               ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop"                               ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z1 S1 P"^zstop"                               ; configure active-high endstop for low end on Z via pin ^zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid


M950 R0 C"exp.heater4" Q2000 L0:24000   					; Create spindle index 0, PWM frequency 2KHz, 
                                                  ; Lmin:max rpm ranges from 0rpm at PWM=0% to 24000rpm at 100% PWM
                                                  ; spindle speed PWM pin	: exp.13 
M563 P0 R0 S"Spindle"                             ; Create Tool 0 with Spindle 0 and call it Spindle

T0						  							; Select Tool 0 (or make sure generated by CAM)

 



M453												; CNC Mode
; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
;M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
;M140 H0                                            ; map heated bed to heater 0
;M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
;M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
;M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
;M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
;M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
;M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
;M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"CNC6040" D0 H1 F0                        ; define tool 0
M453 S0 C"out1" R24000 Q100 T0
M563 S"XYZ-Probe" P1                    ; define XYZ Touch Probe tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                  ; enable support for PanelDue
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                                                 ; select first tool

@cjm said in New codes for use in RRC3.3 M3,M4,M5:

C"exp.13"

Hello CJM,

I have things hooked up properly and I think I have code in Config.g proper, but no signal out to the PWM converter board. I checked with an O-scope. I tried sending M3 P0 S2000. No response.

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jul 30 2021 11:14:49 GMT-0400 (Eastern Daylight Time)

; General preferences

G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"CNC 6040"                                   ; set printer name

; Network
M552 P192.168.1.14 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.2                                  ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X640.00 Y640.00 Z640.00 E420.00                ; set steps per mm
M566 X400.00 Y400.00 Z80.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X2500.00 Y2500.00 Z240.00 E1200.00            ; set maximum speeds (mm/min)
M201 X300.00 Y300.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E500 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X390 Y590 Z68 S0                              ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop"                               ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop"                               ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z1 S1 P"^zstop"                               ; configure active-high endstop for low end on Z via pin ^zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid


M950 R0 C"exp.heater4" Q2000 L0:24000   					; Create spindle index 0, PWM frequency 2KHz, 
                                                  ; Lmin:max rpm ranges from 0rpm at PWM=0% to 24000rpm at 100% PWM
                                                  ; spindle speed PWM pin	: exp.13 
M563 P0 R0 S"Spindle"                             ; Create Tool 0 with Spindle 0 and call it Spindle

T0						  							; Select Tool 0 (or make sure generated by CAM)

 



M453												; CNC Mode
; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
;M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
;M140 H0                                            ; map heated bed to heater 0
;M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
;M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
;M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
;M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
;M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
;M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
;M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"CNC6040" D0 H1 F0                        ; define tool 0
M453 S0 C"out1" R24000 Q100 T0
M563 S"XYZ-Probe" P1                    ; define XYZ Touch Probe tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                  ; enable support for PanelDue
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                                                 ; select first tool

code_text
8/9/2021, 7:11:15 PM 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6JTD2-3S46K-KU0LM
Used output buffers: 1 of 24 (13 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 70264 of which 0 recycled
Never used RAM 20276, free system stack 150 words
Tasks: NETWORK(ready,25.2%,237) HEAT(delaying,0.0%,390) Move(notifyWait,0.1%,309) MAIN(running,74.6%,449) IDLE(ready,0.2%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:08:25 ago, cause: power up
Last software reset at 2021-08-09 18:46, reason: User, GCodes spinning, available RAM 20276, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 28.9, current 39.7, max 40.2
Supply voltage: min 23.8, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max 0/1023
Driver 1: position 0, standstill, SG min/max 0/1023
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-08-09 19:11:12
Cache data hit count 4294967295
Slowest loop: 9.14ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 490658ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 14.94ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

@cjm Hello CJM,
This is exactly what I needed. When you dive into unfamiliar territory it's good to have and idea whats going on.
Thanks so much!

I found some M codes I'd like to use but how? What output will they control? I have a Duet 2 Ethernet. Maybe these codes are only for Duet 3 Mainboard 6HC??
I have my Duet 2 Ethernet controlling the axis on my CNC and I'm working on getting the Spindle to go. I bought one of those PWM to variable voltage out boards. I was reading the link on the forum about that. I was looking into Gcodes and Mcodes on how to run it.
What about M3, M4, and M5??
I found M950. Can this be assigned to any output? (Like E0 or E1)
My 2.2KW spindle has a max RPM of 24,000. At the moment I have a PWM to 0 to 10Volt converter board hooked to the AIN.
I'd like to try sending a trial code to see it turn on just to get a response. Then I could put that into the config.g file if it works.

Mark

code_text
M950 R0 C"!exp.heater3" L12000 ; Spindle 0 uses exp.heater3 as RPM pin and has a max RPM of 12000

Mark

Hello All,
Do I need to modify config.g to get RepRapFirmware 3.3 to work? When rebooting to this software I loose connection to DWC?? So I dropped back to RepRapFirmware 3.2 and all is ok.

Mark

@fcwilt Hey there Frederick. I solved it. X & Y limit switches were swaped even though I thought I paid particular attention to getting them right when wiring! How did that happen! I also found a pin in the connector loose.
Now I need to get the panel du5i working!
Maybe I'll get lucky and have no problems!

Thanks so much!

This is cartesian style CNC.
I'm trying to fix one problem at a time.

code_text
7/30/2021, 8:07:16 PM 	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6JTD2-3S46K-KU0LM
Used output buffers: 3 of 24 (19 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93520 of which 200 recycled
Exception stack ram used: 296
Never used ram: 9076
Tasks: NETWORK(ready,368) HEAT(blocked,504) MAIN(running,1880) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:17:35 ago, cause: power up
Last software reset at 2021-07-30 15:27, reason: User, spinning module GCodes, available RAM 9076 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04417000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 34.4, current 35.0, max 35.5
Supply voltage: min 23.8, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-07-30 20:07:15
Cache data hit count 2023398843
Slowest loop: 9.71ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.2ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 12.55ms; fastest: 0.04ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

Then my config.g

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jul 30 2021 11:14:49 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"CNC 6040"                                   ; set printer name

; Network
M552 P192.168.1.14 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.2                                  ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X400.00 Y400.00 Z400.00 E420.00                ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E500 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X390 Y590 Z68 S0                              ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop"                               ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop"                               ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z1 S1 P"^zstop"                               ; configure active-high endstop for low end on Z via pin ^zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"CNC6040" D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                  ; enable support for PanelDue
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0                                                 ; select first tool

Mark

New setup with Duet2 Ethernet. X-axis not responding to x-axis limit SW. Limit sw are nc and I see they do work and turn on the light for it's axis. I also noticed the motors move so slow.
I want to calibrate movement. I think that has to do with steps per mm. I just need to move what should be 100mm. Until homed I can't get it to move.
Poibt me in the right direction.

Mark

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jul 30 2021 11:14:49 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"CNC 6040"                                   ; set printer name

; Network
M552 P192.168.1.14 S1                              ; enable network and set IP address
M553 P255.255.255.0                                ; set netmask
M554 P192.168.1.2                                  ; set gateway
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X400.00 Y400.00 Z400.00 E420.00                ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E500 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X390 Y590 Z68 S0                              ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop"                               ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop"                               ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z1 S1 P"^zstop"                               ; configure active-high endstop for low end on Z via pin ^zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"CNC6040" D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                  ; enable support for PanelDue
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0                                                 ; select first tool

@phaedrux hELLO Phaedrux,
I got DWC by running a cable from primary router to a secondary router and now DWC is working.
Now I trying to calibrate movement. I also have a problem with X-axis not responding to x-axis limit SW. I see the light toggle on the board but the motor doesn't stop. Maybe M574 cmd? Maybe you can steer me in the right direction for what to fix first and some pointers about how?

Mark

@phaedrux
Ok, I tried it on the other computer but can't even get a connect through YAT terminal.
I hooked again to my computer upstairs and have YAT terminal. I found that only 192.168.0.14 works as a way to get duet web control. If I try 192.168.0.20 0r 192.168.0.12 the connection times out. I checked what it was setup as with M552 and it was set correctly.
There must be something I'm not yet understanding.

code_text
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6JTD2-3S46K-KU0LM
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 92084 of which 20 recycled
Exception stack ram used: 256
Never used ram: 10732
Tasks: NETWORK(ready,524) HEAT(blocked,1456) MAIN(running,1936) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:57:47 ago, cause: power up
Last software reset details not available
Error status: 0
MCU temperature: min 31.5, current 33.0, max 33.4
Supply voltage: min 1.6, current 1.7, max 1.8, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 2021-07-27 12:45:53
Cache data hit count 4294967295
Slowest loop: 55.67ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.9ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 5.91ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex
ok

This is at the computer upstairs where I can get duet web control on 192.168.0.14

Is there anything I can look for settings? Anything you want me to copy and send to you so that you can see??

Mark

@Phaedrux
Hello Phaedrux,
I hoked up Yat terminal on my upstairs computer and set M552 S1 P0.0.0.0
and got 192.168.0.14
I tried that in my browser and I get duet web control.
Now I just need to get the same hooked up direct to the basement computer and hook the Duet to the CNC machine.
I'll try that link you sent and see how far I get.
Why do people need a ethernet switch?? Maybe I should also try a ethernet bridge and a switch??

Mark

@phaedrux I tried pinging again with a small change in address and got this.

code_text
Pinging 192.168.0.20 with 32 bytes of data:
Reply from 192.168.0.15: Destination host unreachable.
Reply from 192.168.0.15: Destination host unreachable.
Reply from 192.168.0.15: Destination host unreachable.
Reply from 192.168.0.15: Destination host unreachable.

Ping statistics for 192.168.0.20:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

@phaedrux The light on the right of the Ethernet port is lit steady and the other flashes green ocasionally.
The router is a wifi router situated upstairs. I could plug into that and try it.

@alankilian I typed that into the browser and it times out. I changed the address to 192.168.0.20 and tried it with same results.

@phaedrux
You can connect it directly, but you will need to make sure the IP address you manually set for the computer and Duet are in the same range.

https://duet3d.dozuki.com/Wiki/Setting_up_networking_on_Duet

Also make sure that your SD card has a /www folder on it with the files for the web interface in it. I do have this folder.

What IP address have you set for the Duet? 192.168.0.20
How have you set it? M552 S1 P192.168.0.20
What IP address have you set for your computer? 192.168.0.15 I looked in properties of my ethernet.
How have you set it? I think it's set different each time I hook to internet.
What happens when you try to reach the IP address of the Duet in your browser?

The connection timed out.
The server at 192.168.1.20 is taking too long to respond.

The site could be temporarily unavailable or too busy. Try again in a few moments.
If you are unable to load any pages, check your computer’s network connection.
If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.

Can you ping the IP address of the Duet from your computer? I tried to ping from cmd prompt but no response.
Can you communicate with the Duet over USB terminal? Yes, I'm using YAT.

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet Ethernet 1.02 or later FIRMWARE_DATE: 2020-05-19b2
This is what came on the Duet 2 Ethernet. The ethernet cable goes to the ethernet on my computer.
in the instructions it says to hook up to the router. Could that be a problem?

Mark

code_text
Network is enabled, configured IP address: 192.168.1.14, actual IP address: 192.168.1.14
ok
Network running, IP address = 192.168.1.14
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6JTD2-3S46K-KU0LM
Used output buffers: 1 of 24 (2 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 92084 of which 20 recycled
Exception stack ram used: 256
Never used ram: 10732
Tasks: NETWORK(ready,1200) HEAT(blocked,1456) MAIN(running,2668) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:25:12 ago, cause: power up
Last software reset details not available
Error status: 0
MCU temperature: min 24.0, current 29.7, max 30.9
Supply voltage: min 0.8, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 3202929715
Slowest loop: 4.16ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.74ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8
Interface state active, link 100Mbps full duplex
ok

@fcwilt Both off nothing going and both doesent sound good. I don't know what would happen.

@fcwilt Hi, Speed control does'nt need to be very precise. I just need to get it in the ball park so cuts will be fast enough. There are 2 inputs for reverse and forward. x1 on and x2 off is forward, x1 off and x2 on is reverse.

Mark

I'd like to use Duet 2 Ethernet. My VFD has FWD or REV and variable speed by 0 to 10 volt input. I saw where I can get a pwm to Voltage converter. I'm wondering which out put of the duet can do this? Maybe I would need to use 2 outputs? I think I can get PWM from heater or fan, but thats only enough to control speed.
I'm sure you guys have a better general knowlege of the Duet2 than I do. Steer me in the right direction!

Mark