I've installed all the updates one by one. And tried to print something and it seems like everything is working. All of my problems have been resolved after the 3.2 update.

Thank you very much for you're time and you're help.
Cheers
George

I've installed all the updates one by one. And tried to print something and it seems like everything is working. All of my problems have been resolved after the 3.2 update.

Thank you very much for you're time and you're help.
Cheers
George

@Phaedrux I tried to instal the 2.0, the 3.0 and 3.2 and it gave me the same message, so I can’t install any one of them.

Hello,

I've tried updating my duet 2 wifi but it doesn't seem to have worked it still says that I'm running on 3.1.1. Meanwhile, my Duet wed control is 3.2.0. When I try to install it, it gives me the message (Error: M997: In-application programming binary "Duet2CombinedIAP.bin" not found).
But that's not my biggest problem, the problem that I've been having is that when I start a print, it prints the base of the model (I've just tried with components with small bases) it prints it fairly well but when it starts printing the wall ( the model is like a box without a lid), it just won't print. It's like if it was going down instead of going up. So the extruder gets stuck and then the print is ruined.
I've looked in cura to see if I haven't put a mirrored setting or something but I couldn't find anything wrong.
I've also looked in my config.g file to see if I haven't put a - somewhere, but I can't find anything.

The strange thing is that I can move all my axes in every directions, the values are right and there is no problem here.
I've also tried printing letters and they came out mirrored compared to cura.

All of these strange things started to happen when I put a probe on the machine and "tried" to update to 3.2.0

The machine :

• Duet 2 wifi + deux 5
• Original BLTouch
• Custom machine (1200x1000x850), Cartesian type

That's my config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Nov 14 2020 12:54:59 GMT+0100 (Central European Standard Time)

; General preferences
G90                                                                     ; send absolute coordinates...
M83                                                                     ; ...but relative extruder moves
M550 P"The Dream Machine"                                               ; set printer name

; Network
M552 S1                                                                 ; enable network
M586 P0 S1                                                              ; enable HTTP
M586 P1 S0                                                              ; disable FTP
M586 P2 S0                                                              ; disable Telnet

; Drives
M569 P0 S1                                                              ; physical drive 0 goes forwards
M569 P1 S0                                                              ; physical drive 1 goes forwards
M569 P2 S1                                                              ; physical drive 2 goes forwards
M569 P3 S0                                                              ; physical drive 3 goes forwards
M569 P4 S1                                                              ; physical drive 4 goes forwards
M569 P5 S0                                                              ; physical drive 5 goes backwards
M569 P6 S1                                                              ; physical drive 6 goes backwards
M569 P7 S1                                                              ; physical drive 7 goes forwards
M569 P8 S0
M569 P9 S0
M584 X0 Y1:5:6:7 Z8:9 E3:4                                                ; set drive mapping
M350 X16 Y16 Z16 E16:16:16:16:16 I1                                     ; configure microstepping with interpolation
M92 X160.00 Y80.00 Z800.00 E420.00:420.00:420.00:420.00:420.00           ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00:120.00:120.00:120.00:120.00         ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00:1200.00:1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00:250.00:250.00:250.00:250.00         ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1200:1200 I30                      ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                                        ; set axis minima
M208 X1000 Y1200 Z850 S0                                                ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                                     ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                                     ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                                                     ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P9 C"^zprobe.in" H5 F120 T7200
G31 P500 X-50 Y-4 Z1.7
M950 S0 C"duex.pwm1"                                                   
M557 X70:900 Y70:1100 S100
M671 X-12.75:1255 S2.5

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138                          ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                                   ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                                                        ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                                 ; map heated bed to heater 0
M143 H0 S75
M570 H0 P150 T15                                                             ; set temperature limit for heater 0 to 75C
M308 S1 P"spi.cs1" Y"thermocouple-max31856"                          ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                                    ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00
M570 H1 P150 T15                                                        ; disable bang-bang mode for heater  and set PWM limit
M308 S2 P"e1temp" Y"thermistor" T100000 B4138                           ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2                                                    ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00                                                        ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1                                                          ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 S"Super Volcano" D0 H1 F0                                       ; define tool 0
G10 P0 X0 Y0 Z0                                                         ; set tool 0 axis offsets
G10 P0 R0 S0                                                            ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Volcano" D1 H2 F1                                             ; define tool 1
G10 P1 X0 Y0 Z0                                                         ; set tool 1 axis offsets
G10 P1 R0 S0                                                            ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                                       ; enable support for PanelDue

That's my M122 :

If someone could help me, it would be awesome because there I'm stuck.

Cheers,
George

I have now figured everything out thanks to all of your support and help.

Thank you very much for replying quickly and for your time
Have a good day

Sincerely George

@Veti I adjusted the bed manually to have it as accurate as I could so the printer doesn't have to compensate too much.

I've done the G28 then the G29 but after that, the only thing that I can do is see the heightmap on the DWC. But how do I load the heightmap into a file with a model in it so it can adjust the height automatically when printing?

What does G32 do?

I've done the update and deleted the "M307 H3 A-1 C-1 D-1", and everything seems to work.

But I have been looking to see how the bed compensation works because my printing surface is very big (1 000 x 1 200mm). I've adjusted it manually has good as I could but it is not sufficient.

The printer has got 2 separate Z-axis, one each side. And a moving Y platform. It's a cartesian printer.

It might be very simple but I can't seem to understand it . What codes do I need to send so I can print something with the bed compensation?

Hello,
I have bought an original BLTouch from "antclabs", I've checked my wiring twice but it still flashing red when I power it up.
When the machine is powered, the tip of the BLTouch deploys touches the glace bed and retracts. It does it twice but then comes back up and doesn't stop flashing red. When you look on the DWC it gives you "Z probe: 1000".
I've also tried different codes like M401 or M280 P0 S10 to test it but nothing happens.
The BLTouch is connected to the PWM1 on the duex board and the two other wire are connected to the duet 2 on the "z probe in" PIN and the "GND" PIN.

The machine is a custom made printer:

• Board : Duet 2 wifi + Duex 5
• Firmware : 3.1.1
• BLTouch : 3.1 original
• That's my config.g :

code_text
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Nov 14 2020 12:54:59 GMT+0100 (Central European Standard Time)

; General preferences
G90                                                                     ; send absolute coordinates...
M83                                                                     ; ...but relative extruder moves
M550 P"The Dream Machine"                                               ; set printer name

; Network
M552 S1                                                                 ; enable network
M586 P0 S1                                                              ; enable HTTP
M586 P1 S0                                                              ; disable FTP
M586 P2 S0                                                              ; disable Telnet

; Drives
M569 P0 S1                                                              ; physical drive 0 goes forwards
M569 P1 S0                                                              ; physical drive 1 goes forwards
M569 P2 S1                                                              ; physical drive 2 goes forwards
M569 P3 S0                                                              ; physical drive 3 goes forwards
M569 P4 S1                                                              ; physical drive 4 goes forwards
M569 P5 S0                                                              ; physical drive 5 goes backwards
M569 P6 S1                                                              ; physical drive 6 goes backwards
M569 P7 S1                                                              ; physical drive 7 goes forwards
M569 P8 S0
M569 P9 S0
M584 X0 Y1:5:6:7 Z8:9 E3:4                                                ; set drive mapping
M350 X16 Y16 Z16 E16:16:16:16:16 I1                                     ; configure microstepping with interpolation
M92 X160.00 Y80.00 Z800.00 E420.00:420.00:420.00:420.00:420.00           ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00:120.00:120.00:120.00:120.00         ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00:1200.00:1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00:250.00:250.00:250.00:250.00         ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1200:1200 I30                      ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                                        ; set axis minima
M208 X1000 Y1200 Z850 S0                                                ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                                     ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                                     ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                                                     ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M307 H3 A-1 C-1 D-1
M558 P9 C"^zprobe.in" H5 F120 T7200
G31 P500 X35 Y4 Z2.1
M950 S0 C"duex.pwm1"                                                   ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                                                ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138                          ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                                   ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                                                        ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                                 ; map heated bed to heater 0
M143 H0 S75
M570 H0 P150 T15                                                             ; set temperature limit for heater 0 to 75C
M308 S1 P"spi.cs1" Y"thermocouple-max31856"                          ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                                    ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00
M570 H1 P150 T15                                                        ; disable bang-bang mode for heater  and set PWM limit
M308 S2 P"e1temp" Y"thermistor" T100000 B4138                           ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2                                                    ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00                                                        ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1                                                          ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 S"Super Volcano" D0 H1 F0                                       ; define tool 0
G10 P0 X0 Y0 Z0                                                         ; set tool 0 axis offsets
G10 P0 R0 S0                                                            ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Volcano" D1 H2 F1                                             ; define tool 1
G10 P1 X0 Y0 Z0                                                         ; set tool 1 axis offsets
G10 P1 R0 S0                                                            ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                                       ; enable support for PanelDue

I'm unable to see what wrong, and I've been pulling my hair to try and make it work but I haven't had any success yet. Could they be a problem with my codes?

Cheers, George