Posts made by gardon64

not a bl touch.
jest two wire, plate and crocodile clip

having trouble with set up of touch probe on duet 3 6xd
cant seam to get the wiring right am i right that it is an analogue type with 2 wires
also can you tell me if there is a ready made macro for the probing thanks in advance

@gardon64
jest a note to say thank you for all your help you were spot on about the usb cable
not back together yet but working

@gardon64 can you pls help

@gardon64 sorry this has been used for cnc had it for about 18 months

has been fine and working all disconnected now trying to reprogram purchased from duet 3d

@gardon64 now done all above still no joy pls help the only lights on are red green red to the left of usb

@gardon64 the board is 2 years old got it from duet 3d and no to your question it has been working fine up to now i have tried to erase the board now get nothing

@Phaedrux
hi still same problem

hi all pc wont connect to my duet 3 6xd
red green red led lit but i get this error Unknown USB Device (Device Descriptor Request Failed) pls help

@o_lampe thank you that’s seams to have changed things

hi all so sorry to be hear again but have a problem
when i make a sq, with carveco software my cnc will only draw one line and then go down through the job can you check my config .g att,hear

; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Mon Jul 24 2023 12:35:53 GMT+0100 (British Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 3" ; set printer name

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1
M569 p0.2 s1 ; physical drive 0.1 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1:0.2 Z0.3 ; set drive mapping
M92 X80.00 Y80.00 Z400.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X500 Y500 Z200 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"io0.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io0.in
M574 Y1 S1 P"io1.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io1.in
M574 Z2 S1 P"io3.in" ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin io3.in

; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid

Thank you all working now

Thanks all figured it out

Ok
Duet 3 6xd board rep rap 3.3
When I run this config .g my z axis will not move but one of the y axis will thanks

this is my config g motor set up z not working help
; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P1.0 S1 ; physical drive 1.0 goes forwards
M584 X0.0 Y0.1:0.2 Z1.0 ; set drive mapping
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X550 Y550 Z150 S0 ; set axis maxima

Error: M569: Response timeout: CAN addr 1, req type 6018, RID=7
still this error

HEAR IS CONFG .G
Configuration file for Duet 3 MB 6XD (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu May 25 2023 12:31:46 GMT+0100 (British Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M453
M550 P"Duet 3 CNC" ; set printer name

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S0 ; physical drive 0.2 goes backwards
M569 P1.0 S1 ; physical drive 1.0 goes forwards
M584 X0.0 Y0.1:O.2 Z0.2 E0.3 ; set drive mapping
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X230 Y0210 Z200 S0 ; set axis maxima

; Endstops
; WARNING: No endstops configured

; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)

; Fans

; Tools
M563 P0 D0 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

NOW I GET
Error: M569: Response timeout: CAN addr 1, req type 6018, RID=3 HELP?

hi all can anyone help me with how to get two stepper motors to work together on y axis
duet 3 6xd