Hi everyone, and happy new year.
I'm trying to config my Delta printer for laser engraving. When I send M452 the printer switches in laser mode but it uses FAN 0 to output for laser beam.
How do I change the output to HEATER E1?
I tried the command M452 P2 R255 F200 but nothing happens. It gives me an error: P2 Bad Parameter.
Can anyone tell me how to config the right setting for the laser? Also, where do I put them in config.g?

This is my config.g :

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Dec 28 2017 21:02:47 GMT+0100 (ora solare Europa occidentale)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 L369.184 R134.167 H368.971 B110 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0.74 Y-0.81 Z0.06 ; Put your endstop adjustments here, or let auto calibration find them
M208 Z0 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops
M558 P5 R0.4 H5 F550 T6000 ; Set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.163 ; Set Z probe trigger value, offset and trigger height
M557 R110 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X64 Y64 Z64 E64 I0 ; Configure microstepping without interpolation
M92 X320.85 Y320.85 Z320.85 E390 ; Set steps per mm
M566 X1000 Y1000 Z1000 E1000 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S100 ; Set temperature limit for heater 0 to 100C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PDelta Star ; Set machine name
M552 S1 ; Enable network
M587 S"fiore_wifi2" P"fiorello1" I192.168.0.24 J192.168.0.1 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0:1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings
M572 D0 S0.25 ; Set control pressure nozzle

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

Thanks.

This is my Delta printer: https://www.youtube.com/watch?v=0tHywe75XXc

Happy New Year to everyone.

Smart effector and panel duo is out of stock,when is come available?Thnks

I would need some help please, when I print for example a 20x20 cube everything's fine but when I print a round piece, tube etc… it's quite small.
For example I printed a 6mm diameter tube and when it finished printing I measured with the caliber and the result was 0.5mm smaller.
Why?
My printer is a Delta, with DUET WIFI, smart effector and magnetic rod.
Thanks in advance

I've solved it. I made an autocalibration with a piece of paper folded three times. Weird, but it solved the problem. Now the height is correct and it prints well.

I set the trigger height(Z-0.447), yet it doesn't change anything. When I start printing, Z height is still too low; I need to use baby step to raise Z to 0.35 to get optimal prints.
My new config.g, after setting the trigger height:

; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 17 2017 23:56:06 GMT+0200 (ora solare Europa occidentale)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R139 L360.22 B125 H235 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them
M208 Z0 S1 ; Set minimum Z
M206 X0 Y0 Z0

; Endstops
M574 X2 Y2 Z2 S1 ; Define active high microswitches
M558 P5 R0.4 F500 H10
G31 P100 X0 Y0 Z-0.447 ; Set Z probe trigger value, offset and trigger height
M557 R105 S20 ; Define mesh grid

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X32 Y32 Z32 E32 I0 ; Configure microstepping without interpolation
M92 X200 Y200 Z200 E172 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z12000 E1200; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E800 I100 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S265 ; Set maximum heater temperature to 265C
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PDUET DELTA ; Set machine name
M552 S1 ; Enable network
M587 Sfiore_wifi2 P"fiorello1" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S1 I0 F500 H0:1 T60 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0:1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

Hi everyone,

I have a Delta printer with DuetWiFi and Smart Effector, when I print the nozzle is too close to the bed. I have to use the baby step to reach the optimal Z height.
Even if I do autocalibration, when I print the Z height is too close to the bed. What's the parameter I need to modify to adjust Z height?

this is my config file:

; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 17 2017 23:56:06 GMT+0200 (ora solare Europa occidentale)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R139 L360.22 B125 H235 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them
M208 Z0 S1 ; Set minimum Z
M206 X0 Y0 Z0

; Endstops
M574 X2 Y2 Z2 S1 ; Define active high microswitches
M558 P5 R0.4 F500 H10
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R105 S20 ; Define mesh grid

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X32 Y32 Z32 E32 I0 ; Configure microstepping without interpolation
M92 X200 Y200 Z200 E172 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z12000 E5000 ; Set maximum speeds (mm/min)
M201 X3000 Y3000 Z3000 E3000 ; Set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E800 I100 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S265 ; Set maximum heater temperature to 265C
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0.3 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PDUET DELTA ; Set machine name
M552 S1 ; Enable network
M587 Sfiore_wifi2 P"fiorello1" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S1 I0 F500 H0:1 T60 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0:1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

@Willy510:

Try putting an M82 not M83 in your start code and that should fix it

Yeah works…..I haven't thought about it....damn.....Thank you

Hi everyone.
I modified a 3d printer FLSUN all-metal; I mounted the DUET WIFI, smart effector and a magnetic rod.
When I start printing my extruder filament goes very fast.
I use Cura 2.5 for slicing.
I've copied the settings from the original Marlin firmware FLSUN but I can't figure out what I'm doing wrong; do I also need to put M83 in start gcode?
All the other settings work well, there are some STL files that work well for the extruder. I can't understand why with Cura my extruder sometimes doesn't work properly.
Thanks.

Ciao a tutti,

Ho modificato una Flsun All Metal,ho montato Duet Wifi,Smart Effector,carbon fiber magnetic rod.Qunado preparo la stampa on Cura 2.5 ho versioni precedenti,tante volte il mio extruder gira molto velocequando inizia la stampa,ho impostato correttamente gli steps,copiandoli dal firmware originale Marlin con quale e arrivata la stampante.
Ci sono file stl che funzionano bene.

Grazie.