@Garfield Makes sense.....I think I was on something magical when I thought about the stepper being 12v......Should have gotten more sleep. I forgot stuff I should have remembered since I have been away from 3d printing for awhile due to health issues. Thanks for explaining

@zapta This is the bowden version that does not have fan or hotend.

@Danal . thanks for the quick answer. So just plug the 12v Hermera in the 24v Duet wifi and since the stepper is rated for 1.33 amps, then set extruder current starting at .65 to .7 amps? Does that sound right?

Hello all, I have a question so I don't harm my new Hermera extruder. I have the bowden version for my delta and it only comes with a 12 volt stepper motor. How can I run this with my version 1.0 Duet Wifi that is being fed 24 volts? Can I just run it at 24v (which I think would cause the stepper to heat up to much) or do I use a buck convertor and if I do, how would I wire that in? Thank you in advance for your expertise in answering this. I very much appreciate it.

the fix is already on the forum and buried. When you unzip the Duet Web Control file you need to have a blank www folder on your sd card and then unzip and place ONLY the contents of the unzipped file into the www folder. Do not place the unzipped file itself in the www folder…...just the contents. Hope this helps someone. The wiki needs changed to address this.

nvm figured it out

Hello, I am new to DuetWifi and I had purchased the first release of the Duet Wifi…..#44 board. When I had finished building my Delta, I tried the board out and all worked with the preloaded V1.15 firmware. I then read all the update warnings and procedures and read all forums and proceeded to upgrade to 1.19. Followed special pre v1.19 procedure through YAT and all is well except that Web Interface control will not come up at all. I can ping the Duet no problem and below is an image of my terminal session, doing what David had advised to others so if someone can help me, PLEASE do. I have tried different versions.....1.18, 1.19, 1.20 all with exactly the same result.

M587
Remembered networks:<lf>KAOS<lf>ok <lf>M552 S1
ok<lf>Wifi module is connected to access point KAOS, IP address 192.168.0.100 <lf>M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.19 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-08-14<lf>ok <lf>M111 S1 P1
Debugging enabled for modules: Network(1)<lf>Debugging disabled for modules: Platform(0) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13)<lf>ok <lf>M111 S1 P2
Debugging enabled for modules: Network(1) Webserver(2)<lf>Debugging disabled for modules: Platform(0) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13)<lf>ok<lf>New conn on socket 0 for local port 80<lf>HTTP connection accepted<lf>Found responder<lf>Received 408 bytes<lf>Sending reply, file = no<lf>HTTP req, command words { GET / HTTP/1.1 }, parameters { }<lf>Webserver: rejecting message with: 404 not found</lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf>

config.h . not g….typo

I am starting by reading configuring RepRapFirmware and try to pick up what I can. Sorry for whining…feeling overwhelmed

ok…I am starting this board from ground up. Is there a manual somewhere telling me my first step and checks to see if things are ok, I guess I thought that the default config that came with this board would just need some tweaks to get it set for my components, but right off the bat Hot end failure and I do not understand how any PID adjustments will change that. It says it starts in Bang Bang which would still not cause it to error out as a failure just turning the board on would it? Is this board to advanced for a noob? This is my first delta and I have only dealt with Ramps and Arduino Mega before, but they just required a little adjustment in the config.g file. I'm sorry but it is frustrating when I have so much not working and not having a gameplan to fix it. I know this is candy for most of you guys but I am trying to decide what to start with and have a checklist to work on....Is there any type of first step, second step and so for a Delta printer with this Duet Wifi? I am more than eager to put in the time to learn and if anyone has a link to where I should start I would be very appreciative. I hope people understand what I am trying to say here....I feel like such a noob when I can't understand something that is second nature to others. Thanks in advance if you can help me, if not then thanks anyway for reading