New with the duet boards.
Hello again thanks for the answers while I was waiting for the answers I realized the problem was from the config then I see the replies I disconnected the 24v from out0. also changed the bed output from out0 to out2. everything is working well right now sorry for the messy wiring and bad "color blob" wiring diagram. it was my first project
Thanks to everyone.
Hello again thanks for the answers while I was waiting for the answers I realized the problem was from the config then I see the replies I disconnected the 24v from out0. also changed the bed output from out0 to out2. everything is working well right now sorry for the messy wiring and bad "color blob" wiring diagram. it was my first project
Thanks to everyone.
@rushmere3d 
Here is a more clear version. how we fix that problem
@ertence also it says beds are off but it's
heating uncontrollably
@stephen6309 Hello again. I check the post you mentioned. but I'm a newbie to be honest haven't noticed any problem. SSR immediately opens when I plug in the power. I can see the temperature but cannot control the relay as i said earlier
Here is my config and bed wiring 
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Tue Jan 26 2021 16:38:54 GMT+0100 (Central European Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"nøkk3d" ; set printer name
M564 H0
; Network
;M551 P"ERTENCE" ; set password
M552 P192.168.1.21 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.168.0.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0.0 goes forwards
M569 P1 S1 ; physical drive 0.1 goes forwards
M569 P2 S1 ; physical drive 0.2 goes forwards
M569 P3 S0 ; physical drive 0.3 goes forwards
M569 P4 S0 ; physical drive 0.3 goes forwards
M569 P5 S0 ; physical drive 0.3 goes forwards
M584 X5 Y1:2 Z3 E4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E436.54 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E500.00 ; set maximum instantaneous speed changes (mm/min)
M203 X15000.00 Y15000.00 Z400.00 E500.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z25.00 E400.00 ; set accelerations (mm/s^2)
M906 X1400 Y2500 Z2500 E1700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 S1 X0 Y-35 Z-5 ; set axis minima
M208 X10000 Y490 Z500 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"io4.in" ; configure active-high endstop for low end on X via pin io0.in
M574 Y1 S1 P"io0.in" ; configure active-high endstop for low end on Y via pin io1.in
M574 Z1 S1 P"io3.in" ; configure active-high endstop for low end on Z via pin io2.in
; Z-Probe
M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io7.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-30 Y-2 Z3.5 ; set Z probe trigger value, offset and trigger height
M557 X20:980 Y10:490 S120 ; define mesh grid
; Heaters
M308 S0 P"temp2" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out2" T0 Q1 ; create heater output on out0 and map it to sensor 0 ; disable bang-bang mode for heater and set PWM limit
M143 H0 S70 ; set temperature limit for heater 0 to 70C
M140 P1 H0
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 Q1 ; create heater output on out1 and map it to sensor 1 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H1 S70 ; set temperature limit for heater 1 to 70C
M140 P2 H1
M308 S2 P"temp3" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H2 C"out3" T2 Q500 ; create heater output on out1 and map it to sensor 1 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H2 S350 ; set temperature limit for heater 1 to 70C
M307 H0 A200.8 C850.6 D2.0 S1.00 V24.0 B0
M307 H1 A200.0 C850.0 D2.0 S1.00 V24.0 B0
M307 H2 A491.0 C185.5.0 D4.9 S1.00 V24.0 B0
; Fans
M950 F0 C"out8" Q3000 ; create fan 0 on pin out4 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out7" Q3000 ; create fan 1 on pin out5 and set its frequency ; set fan 1 value. Thermostatic control is turned on
M106 P1 T45 S1.0 H2
; Tools
M563 P0 D0 H2 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
M501
@jens55 Thanks for your answer I connected one of the heaters for testing but it keeps heating, I cannot get the problem? why is it keep heating?
Hi
i am having some issues with the silicone heater connections with Duet 3 6CH
I have 2x 240V 2000W 500x500 Heaters ; Current : 8.3A , Resistance : 28.8
I am Using 1x 40A SSR My PSU is Meanwell LRS-350-24 do I Need a extra PSU? how can I run 2 beds through to one SSR and Single PSU is it possible? is there any diagram for that type of connection?
Best regards
Hello everyone. I was working on my custom printer was about to get a test print
but the problem is it prints somewhere outside the print area I chose the black area which is selected as print area the red area is the machine starts to print
the Z-axis probing is functional there is no problem with probing its working well. 
here is my cura settings
Here is my config file
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Tue Jan 26 2021 16:38:54 GMT+0100 (Central European Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"nøkk3d" ; set printer name
M564 H0
; Network
;M551 P"ERTENCE" ; set password
M552 P192.168.1.21 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.168.0.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0.0 goes forwards
M569 P1 S1 ; physical drive 0.1 goes forwards
M569 P2 S1 ; physical drive 0.2 goes forwards
M569 P3 S0 ; physical drive 0.3 goes forwards
M569 P4 S0 ; physical drive 0.3 goes forwards
M569 P5 S0 ; physical drive 0.3 goes forwards
M584 X5 Y1:2 Z3 E4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E436.54 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E500.00 ; set maximum instantaneous speed changes (mm/min)
M203 X15000.00 Y15000.00 Z400.00 E500.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z25.00 E400.00 ; set accelerations (mm/s^2)
M906 X1400 Y2500 Z2500 E1700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-25 Y-35 Z0 S1 ; set axis minima
M208 X10000 Y490 Z500 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"io4.in" ; configure active-high endstop for low end on X via pin io0.in
M574 Y1 S1 P"io0.in" ; configure active-high endstop for low end on Y via pin io1.in
M574 Z1 S1 P"io3.in" ; configure active-high endstop for low end on Z via pin io2.in
; Z-Probe
M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io7.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-30 Y-2 Z3.5 ; set Z probe trigger value, offset and trigger height
M557 X20:980 Y10:490 S120 ; define mesh grid
; Heaters
M308 S0 P"temp2" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out2" T0 Q1 ; create heater output on out0 and map it to sensor 0 ; disable bang-bang mode for heater and set PWM limit
M143 H0 S70 ; set temperature limit for heater 0 to 70C
M140 P1 H0
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 Q1 ; create heater output on out1 and map it to sensor 1 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H1 S70 ; set temperature limit for heater 1 to 70C
M140 P2 H1
M308 S2 P"temp3" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H2 C"out3" T2 Q500 ; create heater output on out1 and map it to sensor 1 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H2 S350 ; set temperature limit for heater 1 to 70C
M307 H0 A200.8 C850.6 D2.0 S1.00 V24.0 B0
M307 H1 A200.0 C850.0 D2.0 S1.00 V24.0 B0
M307 H2 A491.0 C185.5.0 D4.9 S1.00 V24.0 B0
; Fans
M950 F0 C"out8" Q3000 ; create fan 0 on pin out4 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out7" Q3000 ; create fan 1 on pin out5 and set its frequency ; set fan 1 value. Thermostatic control is turned on
M106 P1 T45 S1.0 H2
; Tools
M563 P0 D0 H2 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
Best regards
@rjenkinsgb Hello Robert thanks for your answer unfortunately it didn't work for me. I unplug all the slots except the driver 0 and the driver 4 slots as I said these are the slots with problems the others are working at the moment I still control them
@phaedrux these is no problem in phase connection when I plug the cable to the another slot its working there is no problem with the cables