Posts made by Drak

Im looking to use the fan 3 port on my Duex5 expansion board but cant get it to connect.

Here is my config:

M552 S1                                        ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet
M575 P1 B57600 S1
; Drives
M584 X4 Y1:2 Z9:8 E0                                  ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S0                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S1                                         ; physical drive 3 goes forwards
M569 P9 S1    
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4 Z626.4 E100.00                  ; set steps per mm
M566 X500.00 Y500.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X260 Y300 Z350 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P5 C"^zprobe.in" H5 F120 T3000

G31 X20 Y0 Z3 P25


M557 X15:250 Y15:300 S50                           ; define mesh grid

; Heaters
M140 H-1                                           ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                               ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S260                                       ; set temperature limit for heater 0 to 260C

; Fans

M950 F3 C"fan3" Q200 ; create fan 0 on pin fan0 and set its frequency
M106 P3 S0 H-1       ; set fan 0 value. Thermostatic control is turned off


; Tools
M563 P0 D0 H0 F3 S"Main"                                      ; define tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P0 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss


0

@Phaedrux I tried connecting to the fan port 3 on the duex 5 board but i get this error when i run the m106 command

On my dashboard no fans appear:

here is my config

M552 S1                                        ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet
M575 P1 B57600 S1
; Drives
M584 X4 Y1:2 Z9:8 E0                                  ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S0                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S1                                         ; physical drive 3 goes forwards
M569 P9 S1    
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4 Z626.4 E100.00                  ; set steps per mm
M566 X500.00 Y500.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X260 Y300 Z350 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P5 C"^zprobe.in" H5 F120 T3000

G31 X20 Y0 Z3 P25


M557 X15:250 Y15:300 S50                           ; define mesh grid

; Heaters
M140 H-1                                           ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                               ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S260                                       ; set temperature limit for heater 0 to 260C

; Fans

M950 F3 C"fan3" Q200 ; create fan 0 on pin fan0 and set its frequency
M106 P3 S0 H-1       ; set fan 0 value. Thermostatic control is turned off


; Tools
M563 P0 D0 H0 F3 S"Main"                                      ; define tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P0 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@Phaedrux the fans came in a set of 4 so i tried another and had the same result. Should i try it on one of the duex 5 fan headers?

@Phaedrux

M122 results:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.1 (2022-06-01 21:05:28) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-956GU-DJMSN-6JKF0-3SJ6T-KBNRD
Used output buffers: 3 of 26 (12 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 75300 of which 0 recycled
Never used RAM 12920, free system stack 184 words
Tasks: NETWORK(ready,12.4%,235) HEAT(notifyWait,0.0%,333) Move(notifyWait,0.0%,363) DUEX(notifyWait,0.0%,24) MAIN(running,86.0%,416) IDLE(ready,1.6%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:49 ago, cause: software
Last software reset at 2023-09-27 22:48, reason: User, GCodes spinning, available RAM 12920, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 32.7, current 33.9, max 34.3
Supply voltage: min 12.2, current 12.2, max 12.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: standstill, SG min n/a
Driver 6: standstill, SG min n/a
Driver 7: standstill, SG min n/a
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min n/a
Driver 10: 
Driver 11: 
Date/time: 1970-01-01 00:00:00
Cache data hit count 1702803860
Slowest loop: 23.56ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== DueX ===
Read count 1, 1.21 reads/min

M98 results:
M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Heater 1 not found
Error: Heater 2 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found

@Phaedrux said in Part Cooling Fan Setup:

Which Duet board?

Duet wifi 2 and Duex 5

@Drak said in Part Cooling Fan Setup:

When i go to test the fan on the dashboard

What exactly do you mean by this?

I meant that i tried moving the fan slider bar on the dashboard and nothing happens

Does the fan work if you send M106 P0 S1?

No nothing happens, when i plug the fan into always on 5v it turns on though.

I am trying to setup up a fan for part cooling during printing after the first layer is complete. I am using a 5v blower fan in the fan 0 port. Ive plugged it into the 5v always on port to make sure it works.

When i go to test the fan on the dashboard and turn it on nothing happens did i set it up correctly?

here is my config:

; Heaters
M140 H-1                                           ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                               ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S260                                       ; set temperature limit for heater 0 to 260C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1       ; set fan 0 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H0 F0 S"Main"                                      ; define tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P0 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@OwenD Im running the board with a 24v ps

I would like to use a 12v blower fan for my part cooling fan but how would i wire it on a duet wifi 2 board (i also have the duex 5 extension).

@Phaedrux Thank you, I got this error when homing, I leveled the bed again and got same error but at a lower max error. how do i establish a a Z=0 datum?

Warning: Skipping grid point X=15.0, Y=265.0 because Z probe cannot reach it
Warning: the height map has a substantial Z offset. Suggest use Z-probe to establish Z=0 datum, then re-probe the mesh.
24 points probed, min error 0.302, max error 3.056, mean 1.826, deviation 0.716
Height map saved to file 0:/sys/heightmap.csv
9/9/2023, 5:45:40 PM 	Warning: Skipping grid point X=15.0, Y=165.0 because Z probe cannot reach it
Warning: Skipping grid point X=15.0, Y=215.0 because Z probe cannot reach it
9/9/2023, 5:44:32 PM 	Warning: Skipping grid point X=15.0, Y=65.0 because Z probe cannot reach it
Warning: Skipping grid point X=15.0, Y=115.0 because Z probe cannot reach it
9/9/2023, 5:43:23 PM 	G28 Z
Warning: Skipping grid point X=15.0, Y=15.0 because Z probe cannot reach it

@Phaedrux
I added the M558 line to the config and now it goes to probe. However during probing the bed moves in the wrong direction.
here is the new config: the homez.g is the same as before:

; Drives
M584 X4 Y1:2 Z9:8 E0                                  ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S0                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S0                                         ; physical drive 3 goes forwards
M569 P9 S0    
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4 Z626.4 E100.00                  ; set steps per mm
M566 X500.00 Y500.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X300 Y400 Z500 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P5 C"^zprobe.in" H5 F120 T3000

G31 X20 Y0 Z9 P25


M557 X15:762 Y15:762 S20                           ; define mesh grid

; Heaters
M140 H-1                                           ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                               ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S260                                       ; set temperature limit for heater 0 to 260C

; Fans

; Tools
M563 P0 D0 H0 S"Main"                                      ; define tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P0 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

here are the M122 and M98 responses:

9/7/2023, 11:40:45 PM 	M98 P"config.g" i
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: bad grid definition: Too many grid points; suggest increase spacing to 37.3mm
Error: Heater 1 not found
Error: Heater 2 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found
9/7/2023, 11:40:19 PM 	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.1 (2022-06-01 21:05:28) running on Duet WiFi 1.02 or later + DueX5
Used output buffers: 3 of 26 (23 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 75200 of which 0 recycled
Never used RAM 12948, free system stack 134 words
Tasks: NETWORK(ready,13.7%,242) HEAT(notifyWait,0.0%,333) Move(notifyWait,0.0%,296) DUEX(notifyWait,0.0%,24) MAIN(running,85.8%,410) IDLE(ready,0.5%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:03:43 ago, cause: software
Last software reset at 2023-09-07 23:36, reason: User, GCodes spinning, available RAM 13108, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 32.8, current 34.1, max 34.8
Supply voltage: min 12.2, current 12.2, max 12.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min 0
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min 0
Driver 5: standstill, SG min n/a
Driver 6: standstill, SG min n/a
Driver 7: standstill, SG min n/a
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min n/a
Driver 10: 
Driver 11: 
Date/time: 2023-09-07 23:40:15
Cache data hit count 4294967295
Slowest loop: 59.06ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.2ms, write time 3.0ms, max retries 0
=== Move ===
DMs created 83, segments created 3, maxWait 15424ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 17, completed 17, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 2], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== DueX ===
Read count 1, 0.27 reads/min
=== Network ===

Hello I am trying to setup my Z probe (using a NPN sensor) and ultimately complete a mesh level of my bed. When i home the z, it goes to the first probe point in the x and y directions but the Z axis doesn't move. Then it says homing is completed with a random Z value listed as homed.

Here is my Config:

; Drives
M584 X4 Y1:2 Z9:8 E0                                  ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S0                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S0                                         ; physical drive 3 goes forwards
M569 P9 S0    
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4 Z626.4 E100.00                  ; set steps per mm
M566 X500.00 Y500.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X300 Y400 Z500 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; Z-Probe


G31 X20 Y0 Z9 P25


M557 X15:762 Y15:762 S20                           ; define mesh grid

; Heaters
M140 H-1                                           ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                               ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S260                                       ; set temperature limit for heater 0 to 260C

; Fans

; Tools
M563 P0 D0 H0 S"Main"                                      ; define tool 1
G10 P0 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P0 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Here is my homez.g:

G91              ; relative positioning
G1 H2 Z5 F6000   ; lift Z relative to current position
G90              ; absolute positioning
G1 X15 Y15 F6000 ; go to first probe point
G30              ; home Z by probing the bed

@Phaedrux Thank you it worked

@jay_s_uk

Thank you,
I have that in my config but does it need to go in my homey.g also?

M584 X4 Y1:2 Z9:8 E0 U2                                   ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S0                                         ; physical drive 3 goes forwards
M569 P9 S0    

M350 X16 Y16:16 Z16 E16 U16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4:793.4 Z626.4 E100.00 U793.4                  ; set steps per mm
M566 X500.00 Y500.00:500.00 Z60.00 E120.00 U500.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00:600.0 Z180.00 E1200.00 U600.0            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00:25.0 Z20.00 E250.00 U25.0                ; set accelerations (mm/s^2)
M906 X800 Y800:800 Z800 E800 U800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits

M208 X0 Y0 U0 Z0 S1                                   ; set axis minima
M208 X300 Y600 Z500 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

I have a y axis with 2 motors in which im triyng to use 2 endstops (one per motor). When i home the printer in the y axis only one motor turns. Am i missing something?

Here is my config

M584 X4 Y1:2 Z9:8 E0 U2                                   ; set drive mapping
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes FORwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M569 P5 S0  
M569 P6 S0                                         ; physical drive 3 goes forwards
M569 P7 S0                                         ; physical drive 3 goes forwards
M569 P8 S0                                         ; physical drive 3 goes forwards
M569 P9 S0    
M350 X16 Y16:16 Z16 E16 U16 I1                            ; configure microstepping with interpolation
M92 X816.5 Y793.4:793.4 Z626.4 E100.00 U793.4                  ; set steps per mm
M566 X500.00 Y500.00:500.00 Z60.00 E120.00 U500.00                ; set maximum instantaneous speed changes (mm/min)
M203 X600.00 Y600.00:600.0 Z180.00 E1200.00 U600.0            ; set maximum speeds (mm/min)
M201 X25.00 Y25.00:25.0 Z20.00 E250.00 U25.0                ; set accelerations (mm/s^2)
M906 X800 Y800:800 Z800 E800 U800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 U0 Z0 S1                                   ; set axis minima
M208 X300 Y600 Z500 S0                             ; set axis maxima

; Endstops

M574 X1 S1 P"!xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-high endstops for low end on Z via pins zstop and e1stop

M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

Here is my homey.g

G90                    ; absolute positioning
M584 Y1 U2 P4      ; split two Y motors
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y-905 F1800
G1 H1 U-905 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 U5 F6000    ; go back a few mm
G1 H1 U-905 F360
G1 H1 U-905 F360  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
M584 Y1:2 P3       ; re-join Y motors 
G90              ; absolute positioning

@phaedrux
tuned at lower temp, seems to heat faster. how do i activate bang bang mode again?

@phaedrux
it takes around 15 minutes to get to 205. band bang mode is when you turn B0 to B1 correct?

the problem on the other thread was that it wasnt heating up at all, i found an error in my wiring, now it heats up but seems it could heat faster.

I have been testing this hotend i made myself, controlling it with a duet wifi. I am able to heat it up now but it heats up at a low rate. ( i can get to a temp of around 205 but it takes a while). I thought running M303, tuning, would help with that but i recieve this error when i do the tuning.

I explained the hot end heater in this other post i made
since that post i have found more permanent positions for the temp sensors and securing them with screws.

https://forum.duet3d.com/topic/28622/heater-code-setup-question/15?_=1655061706238

@phaedrux this setup is just to workout the duet control side of the heating element and make sure i can heat up the aluminum consistantly

@phaedrux the goal is to use this heating element long term

@phaedrux
how do i activate bang bang mode?

@phaedrux should i directly tape them to the heating element?