@phaedrux Sure,
It's the raise 3d pro tablet!, totally closed of course.
it must be usb to serial comm's and the arduino was just to prove a point, that the host tablet will recognize the correct VID_PID the duet will take place of the arduino.
I would like to use duwt wifi under host control of the raise tablet (printing over usb basically) but i need to change the vendor id and product id of the duet.
thank you
What I meant to add was....
Is it possible to configure the duet wifi vid_pid at all?
Thanks...
Hi all,
I have an application for my duet WiFi board that needs to controlled from a host system.
It will only accept USB devices with a certain vid_pid, I have proved this with a custom Arduino and USB identification. I can send a string of data that replicates what is sent from the duet over USB and it seems to work.
However, when I connect the duet it obviously has the wrong identification and will not connect, I was thinking of a custom USB to serial converter and use the panelduet serial connection but I fear this will be too slow for the required 230400 baud.
Any ideas out there?
Thanks in advance
Ian
Yes please that would be kind...I have the 3d chameleon simplify profile...but I have not tried anything yet,...just doing the ground work.....
I'm sure they will match, they are from the same manufacture. I was just thinking out loud.
I appreciate the advice,...everyone!...
My cube pro now works well, it has a 600w silicone heat mat, 360x 290 x 225z print area.
I have removed the original x carriage ...it was HEAVY....it now has a temporary one....flat plate with bondtech clone, mosquito clone hotend and linear bearings attached by terry clips for easy removal.....no expense spared.!
I might have to incoparate a compensator mechanism to account for any difference between drives but that's another thread!...
Once again thank you!
Looks great...
I didn't think about doing it in definitions......hey ho!.........
Simple really...DOH!
I'll give it a try when my expansion board arrives in the next few days...
Thank you so much for the help......
Hi all.....
I am designing a multiple material system for my duet wifi driven machine.
I have a cartesian machine (cube pro duo chassis) using one extruder on the carriage.
What I would like to to do is have a filament merger, a bit like 3d chameleon, retain the single direct drive on the carriage but feed it via five seperate bondtech extruders driven from a duex board, meaning that at any one time the tool extruder will be the main one on the carriage AND one of the other five running one to one...ie the external extruder feeding the main one.
Of course the steps must be the same and there is no room for feed errors but it's only a test.....
This way, to change material i would retract both drives, change to another feeder drive and run this one along with the main one to allow colour or material changes.
NOW!...I know axis can be mapped for x y and z but can they also be mapped to run two extruder..or extruder and expansion drive simultaneously?.......and how would i arrange the code?...
I guess M584 and something...but I would need to change this on a tool change routine....
any help would be greatly appreciated
Thank you.........
Hmmm...ok..
Thank you for your assistance anyhow,..one for the memory banks...
I am so very sorry!
I lowered the supply down to 25v and now its reliable on start up..I guess the load from the bed current dropped the voltage just enough, although i doubt the cpu was in shutdown.
I have also had a horrible thought...I had wifi issues earlier in the year, random disconnects and connection failures...I wonder uif they were related.........
I might re graft the wifi board and try again...
Once again, please accept my apologies i missed this one by a mile,...if it's any consolation,...I really like using the duet.
I now have three machines running it and will spread the word, you support is second to none!
my meter shows 27.85..off load!!!..ill drop it back to 25..and retry...
tried it with ethernet disconnected just in case...still no difference...
19:48:06
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.01(RTOS) running on Duet Ethernet 1.02 or later
Board ID: 08DGM-956GU-DJMSN-6J1DJ-3S86L-K9R3G
Used output buffers: 3 of 20 (13 max)
=== RTOS ===
Static ram: 28476
Dynamic ram: 95932 of which 16 recycled
Exception stack ram used: 272
Never used ram: 6376
Tasks: NETWORK(ready,328) HEAT(blocked,1324) MAIN(running,3564)
Owned mutexes:
=== Platform ===
Last reset 00:01:02 ago, cause: software
Last software reset at 2018-10-15 19:47, reason: User, spinning module GCodes, available RAM 6140 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 28.3, current 29.0, max 29.1
Supply voltage: min 27.6, current 27.7, max 27.8, under voltage events: 0, over voltage events: 0
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 2018-10-15 19:48:06
Slowest loop: 6.17ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 6.22ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state: 5
=== Expansion ===
still says disconnected until i issue M140 S(>55)...
I'll uncomment the last line of config for now...
Voltage test with meter did not show anything wrong....
PUZZLE....
I'll do that...I wonder if the voltage is under low load. switching the bed on causes current draw and the psu to step up?
It's printing now, I'll try that tomorrow..i'll also drop a volt test on it...
Thank you.
Ok, initial power on..24v only, last line of config removed.
M408
{"status":"O","heaters":[44.0,54.9],"active":[0.0,55.0],"standby":[0.0,55.0],"hstat":[0,2],"pos":[0.000,0.000,0.000],"machine":[0.000,0.000,0.000],"sfactor":100.00,"efactor":[100.00],"babystep":0.000,"tool":0,"probe":"1000","fanPercent":[30.0,100.0,100.0,0.0,0.0,0.0,0.0,0.0,0.0],"fanRPM":0,"homed":[0,0,0],"msgBox.mode":-1}
after m140 s55 issued
M408
{"status":"I","heaters":[52.2,55.0],"active":[55.0,55.0],"standby":[0.0,55.0],"hstat":[2,2],"pos":[0.000,0.000,0.000],"machine":[0.000,0.000,0.000],"sfactor":100.00,"efactor":[100.00],"babystep":0.000,"tool":0,"probe":"1000","fanPercent":[30.0,100.0,100.0,0.0,0.0,0.0,0.0,0.0,0.0],"fanRPM":0,"homed":[0,0,0],"msgBox.mode":-1}
Checked wiring,..all good..is it worth re updating duet and panel duet?
Any ideas...
thank you..
when my current print is complete i'll double check......
Duet is powered all the time from startup, no usb input.
if i set bed temp to 55 or more it goes to idle if i then set bed temp to 0 everything still works.
only power source is Vin 24v...(actually 27.5)..maybe a litlle high?
and yes that solves my problem I just don't like not knowing why..
panel duet says "disconnected" but still reports temperature changes...so it must be connected right?...it won't read memory card until i do the bed temp thingy...
a real puzzler...
also if i pause and canccel a print, when i restart it it homes but hangs..this may be a slicer issue but the first run is fine and if i do a second after completion it's fine...only a problem if cancelled...
Hi guys,
As a work around i've set the bed to 55 degrees in the last line of config.g.
looks like it's working.
I don't think i've done anything wrong with my config?..apart from lack of comments....
; General preferences
M555 P5 ; Set firmware compatibility to look like Repetier
M667 S1 ; Select CoreXY mode
M552 S1 ; Enable network
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M111 S0 ; Debug off
; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X100 Y100 Z1520 E143 ; Set steps per mm
M566 X500 Y500 Z40 E100 ; Set maximum instantaneous speed changes (mm/min)
M203 X30000 Y30000 Z1500 E20000 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z500 E1000 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X340 Y220 Z267 S0 ; Set axis maxima
; Endstops
M574 X1 Y1 Z2 S1 ; Set active high endstops
m558 p4
; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S140 ; Set temperature limit for heater 0 to 140C
M305 P1 T100000 B4725 C7.06e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S350 ; Set temperature limit for heater 1 to 350C
;M301 H1 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 0
;M301 H2 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 1
; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 ; Define tool 1
G10 P0 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P0 R55 S55 ; Set initial tool 0 active and standby temperatures to 0C
; Miscellaneous
M501 ; Load saved parameters from non-volatile memory
T0
M572 D0 S0.03
M140 S55
Once again many thanks for a great product.
Sorry!...
it's 1.21.3(13b1)
my bad.
thanks again for your help...
hi,
firmware is PanelDue-5.0i-7.0i
but i seam to remeber it doing similar before i updated it...
thsnks